ページ1に含まれる内容の要旨
Drywall Screwdriver
MODEL 6823N
MODEL 6824N
002604
DOUBLE
INSULATION
INSTR U CTION MANU AL
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
ページ2に含まれる内容の要旨
SPECIFICATIONS Model 6823N 6824N Self drilling screw 6 mm (1/4”) 6 mm (1/4”) Capacities Drywall screw 6 mm (1/4”) 5 mm (3/16”) No load speed (RPM) 0 - 2,500/min. 0 - 4,500/min. Overall length 301 mm (11-7/8”) 290 mm (11-3/8”) Net weight 1.5 kg (3.4 lbs) 1.4 kg (3.1 lbs) • Manufacturer reserves the right to change specifications without notice. Specifications may differ from country to country. GENERAL SAFETY RULES USA002-2 (For All Tools) WARNING: Read and understand all instructions. Failure
ページ3に含まれる内容の要旨
5. Avoid body contact with grounded sur- 14. Use safety equipment. Always wear eye faces such as pipes, radiators, ranges and protection. Dust mask, non-skid safety refrigerators. There is an increased risk of shoes, hard hat, or hearing protection must electric shock if your body is grounded. be used for appropriate conditions. Ordinary eye or sun glasses are NOT eye protection. 6. Do not expose power tools to rain or wet conditions. Water entering a power tool will Tool Use and Care increase t
ページ4に含まれる内容の要旨
24. When servicing a tool, use only identical SERVICE replacement parts. Follow instructions in 23. Tool service must be performed only by the Maintenance section of this manual. qualified repair personnel. Service or main- Use of unauthorized parts or failure to follow tenance performed by unqualified personnel Maintenance instructions may create a risk of could result in a risk of injury. electric shock or injury. USE PROPER EXTENSION CORD: Make sure your extension cord is in good condition. W
ページ5に含まれる内容の要旨
SAVE THESE INSTRUCTIONS WARNING: MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury. SYMBOLS USD201-2 The followings show the symbols used for tool. V ....................... volts ....................no load speed n ˚ A ....................... amperes ....................Class II Construction Hz ..................... hertz .../min................revolutions or reciprocation per minute ................ alternating current 5
ページ6に含まれる内容の要旨
FUNCTIONAL CAUTION: DESCRIPTION • Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. 002612 Depth adjustment 1 The depth can be adjusted by turning the locking sleeve. A Turn it in “A” direction for less depth and in “B” direction for more depth. One full turn of the locking sleeve equals 1.5 mm (1/16”) change in depth. B 1. Locking sleeve 002619 Adjust the locking sleeve so that the distance between the tip of the locator and the screw
ページ7に含まれる内容の要旨
To stop the tool from the locked position, pull the switch trig- ger fully, then release it. NOTE: • Even with the switch on and motor running, the bit will not rotate until you fit the point of the bit in the screw head and apply forward pressure to engage the clutch. 002635 Reversing switch action 1 This tool has a reversing switch to change the direction of A rotation. Move the reversing switch lever to the position (A side) for clockwise rotation or the position (B side) for counterclockwi
ページ8に含まれる内容の要旨
Installing or removing the bit 002653 To remove the bit, first pull the locator out of the locking sleeve. Then grasp the bit with a pair of pliers and pull the bit out of the magnetic bit holder. Sometimes, it helps to wiggle the bit with the pliers as you pull. 1 2 1. Locator 2. Locking sleeve 002661 To install the bit, push it firmly into the magnetic bit holder. Then install the locator by pushing it firmly back onto the 1 locking sleeve. 2 3 1. Locator 2. Bit 3. Magnetic bit holder OPERATIO
ページ9に含まれる内容の要旨
To maintain product SAFETY and RELIABILITY, repairs, car- bon brush inspection and replacement, any other mainte- nance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. ACCESSORIES CAUTION: • These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for it
ページ10に含まれる内容の要旨
Memo 10
ページ11に含まれる内容の要旨
Memo 11
ページ12に含まれる内容の要旨
Memo 12
ページ13に含まれる内容の要旨
Stamp Timbre Makita Canada Inc. 1950 Forbes Street, Whitby, Ontario L1N 7B7 Fold 13 Cut
ページ14に含まれる内容の要旨
Your answers to the following questions are appreciated. 1. This product was purchased from? 3. How did you first learn of Makita Power Tools? Hardware/lumber Store Industrial Supply Magazine/Newspaper Catalog Tool Distributor Other ( ) From dealer Other ( ) Store display 2. Use of the product is intended for? 4. Most favored points are? Construction trade Home maintenance Design Makita Brand Industrial maintenance Other ( ) Features Power Size
ページ15に含まれる内容の要旨
Factory Service Centres Head Office: 1950 Forbes St., Whitby, Ontario, L1N 7B7 (905) 571 - 2200 1-800-263-3734 Regional Office: 11771 Hammersmith Way, Richmond B.C. V7A 5H6 (604) 272 - 3104 1-800-663-0909 Regional Office: 6389 boul, Couture, St. Leonard, Quebec (Montreal) H1P 3J5 (514) 323 - 1223 1-800-361-7049 Dartmouth: 202 Brownlow Avenue Dartmouth, N.S., B3B 1T5 (902) 468 - 7064 1-888-625-4821 Ville St. Laurent: 1140 Rue Bégin, Ville St. Laurent, Quebec (Montreal) H4R 1X1 (514) 745 -
ページ16に含まれる内容の要旨
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centres. If inspection shows the trouble is caused by defective workmanship or material, M
