ページ1に含まれる内容の要旨
Drywall Screwdriver
MODEL 6823
MODEL 6824
MODEL 6825
DOUBLE
INSULATION
INSTR U CTION MANU AL
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
www.makitatools.com
ページ2に含まれる内容の要旨
SPECIFICATIONS Model 6823 6824 6825 Self drilling screw 6 mm (1/4”) Capacities Drywall screw 5 mm (3/16”) No load speed (RPM) 0 - 2,500/min. 0 - 4,500/min. 0 - 6,000/min. Overall length 301 mm (11 - 7/8”) 290 mm (11 - 3/8”) 290 mm (11 - 3/8”) Net weight 1.5 kg (3.4 lbs) 1.4 kg (3.1 lbs) 1.4 kg (3.1 lbs) • Manufacturer reserves the right to change specifications without notice. Specifications may differ from country to country. GENERAL SAFETY RULES USA002-2 (For All Tools) WARNING: Read and und
ページ3に含まれる内容の要旨
5. Avoid body contact with grounded sur- 14. Use safety equipment. Always wear eye faces such as pipes, radiators, ranges and protection. Dust mask, non-skid safety refrigerators. There is an increased risk of shoes, hard hat, or hearing protection must electric shock if your body is grounded. be used for appropriate conditions. Ordinary eye or sun glasses are NOT eye protection. 6. Do not expose power tools to rain or wet conditions. Water entering a power tool will Tool Use and Care increase t
ページ4に含まれる内容の要旨
24. When servicing a tool, use only identical SERVICE replacement parts. Follow instructions in 23. Tool service must be performed only by the Maintenance section of this manual. qualified repair personnel. Service or main- Use of unauthorized parts or failure to follow tenance performed by unqualified personnel Maintenance instructions may create a risk of could result in a risk of injury. electric shock or injury. USE PROPER EXTENSION CORD: Make sure your extension cord is in good condition. W
ページ5に含まれる内容の要旨
SAVE THESE INSTRUCTIONS WARNING: MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury. SYMBOLS USD201-2 The followings show the symbols used for tool. V ....................... volts ....................no load speed n ˚ A ....................... amperes ....................Class II Construction Hz ..................... hertz .../min................revolutions or reciprocation per minute ................ alternating current 5
ページ6に含まれる内容の要旨
FUNCTIONAL CAUTION: DESCRIPTION • Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. 002612 Depth adjustment 1 The depth can be adjusted by turning the locking sleeve. A Turn it in “A” direction for less depth and in “B” direction for more depth. One full turn of the locking sleeve equals 1.5 mm (1/16”) change in depth. B 1. Locking sleeve 002619 Adjust the locking sleeve so that the distance between the tip of the locator and the screw
ページ7に含まれる内容の要旨
For continuous operation, pull the switch trigger and then push in the lock button. To stop the tool from the locked position, pull the switch trig- ger fully, then release it. NOTE: • Even with the switch on and motor running, the bit will not rotate until you fit the point of the bit in the screw head and apply forward pressure to engage the clutch. 002635 Reversing switch action 1 This tool has a reversing switch to change the direction of A rotation. Move the reversing switch lever to the po
ページ8に含まれる内容の要旨
ASSEMBLY CAUTION: • Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. Installing or removing the bit 002653 To remove the bit, first pull the locator out of the locking sleeve. Then grasp the bit with a pair of pliers and pull the bit out of the magnetic bit holder. Sometimes, it helps to wiggle the bit with the pliers as you pull. 1 2 1. Locator 2. Locking sleeve 002661 To install the bit, push it firmly into the magnetic bit holder. Then insta
ページ9に含まれる内容の要旨
MAINTENANCE CAUTION: • Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, repairs, car- bon brush inspection and replacement, any other mainte- nance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. ACCESSORIES CAUTION: • These accessories or attachments are recommended for use with your Makita tool specified in this
ページ10に含まれる内容の要旨
Memo 10
ページ11に含まれる内容の要旨
Memo 11
ページ12に含まれる内容の要旨
Memo 12
ページ13に含まれる内容の要旨
First-Class Postage Required Post Office will not deliver without proper postage. Makita U.S.A., Inc. 14930 Northam Street La Mirada, CA 90638-5753 Fold 13 Cut
ページ14に含まれる内容の要旨
MAIL THIS PORTION Your answers to the following questions are appreciated. 1. This product was purchased from: 3. How did you learn about this product: Home Center Other ( ) Magazine Radio Hardware/Lumber Store From Dealer Exhibition Tool Distributor Newspaper From Friend Industrial Supply Store Display Previous Usage Construction Supply Catalog Other ( ) 2. Use of the product is intended for: 4. Most favored points are: Construction Trade Design Repair Se
ページ15に含まれる内容の要旨
FACTORY SERVICE CENTERS 1-800-4-MAKITA RETAIN THIS PORTION FOR YOUR RECORDS ARIZONA FLORIDA MISSOURI PENNSYLVANIA 3707 E. Broadway Rd., Ste. 6 750 East Sample Road 9876 Watson Road 1704 Babcock Blvd. Phoenix, AZ 85040 Pompano Beach, FL 33064 St. Louis, MO 63126-2221 Pittsburgh, PA 15209 (602) 437-2850 (954) 781-6333 (314) 909-9889 (412) 822-7370 CALIFORNIA GEORGIA NEBRASKA PUERTO RICO 41850 Christy St. 4680 River Green Parkway NW 4129 S. 84th St. 200 Guayama St. Fremont, CA 94538-5107 Duluth,
ページ16に含まれる内容の要旨
WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of
