ページ1に含まれる内容の要旨
Screwdriver
MODEL 6805BV
Variable speed I Reversing
INSTRUCTION MANUAL
DOUBLE
INSULATION
SPEC IF I CAT I 0 N S
Self drilling screw Machine screw Wood screw
* Manufacturer reserves the right to change specifications without notice.
* Note: Specifications may differ from country to country.
WARNING: For your personal safety, READ and UNDERSTAND before using
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
ページ2に含まれる内容の要旨
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp or wet locations. Keep work area well lit. Don't expose power tools to rain. Don't use tool in presence of f
ページ3に含まれる内容の要旨
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don’t carry tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so marked. 17. STAY ALERT. Watch what you are doing, use common sense. Don’t operate tool when you are tired. 18.
ページ4に含まれる内容の要旨
ADDITIONAL SAFETY RULES 1. Always be sure you have a firm footing. Be sure no one is below when using the tool in high locations. 2. Hold the tool firmly. 3. Keep hands away from rotating parts. When driving into walls, floors or wherever "live" electrical wires may be 4. encountered, DO NOT TOUCH ANY METAL PARTS OF THE TOOL! Hold the tool only by the insulated grasping surfaces to prevent electric shock if you drive into a "live" wire. 5. Do not touch the bit or the workpiece immediat
ページ5に含まれる内容の要旨
Removing or installing bit CAUTION : Always be sure that the tool is switched off and unplugged before removing or installing the bit. To remove the bit, first pull the front cap off and then pull the bit firmly. To install the bit, insert it into the tool as far as it will go and then replace the front cap. Depth adjustment When you wish to drive self drilling screws, etc., adjust the depth as follows. Turn the locator to adjust the depth. I Adjusting ring- \\ Initially, adjust the
ページ6に含まれる内容の要旨
Adjusting fastening torque I When you wish to drive machine screws, wood screws, hex bolts etc. with the pre- determined torque, adjust the fastening torque as follows. The fastening torque may be adjusted by turning the adjusting ring. Before turning the adjusting ring, turn the locator in the direction of the arrow as far as it will go without forcing. The torque is increased by turning the adjusting ring in the direc- tion of the arrow and decreased by turn- ing it in the opposit
ページ7に含まれる内容の要旨
Reversing switch action This tool has a reversing switch to change the direction of rotation. Move the revers- ing switch lever to the &? position for clockwise rotation or the position for counterclockwise. Reversing switch lever 1 CAUTION : Always check the direction of rotation before operation. *Use the reversing switch only when the tool comes to a complete stop. Changing the direction of rotation before the tool stops may ruin the tool. Operation Fit the screw on the point of t
ページ8に含まれる内容の要旨
NOTE : 0 Make sure that the driver bit is inserted straight in the screw head, or the screw and/or bit may be damaged. When driving wood Screws, predrill pilot of wood screw of pilot hole holes to make driving easier and to pre- vent splitting of the workpiece. See the chart. 1 1/64" 1/8" 3/16" iia" 13/64" 9/64" 7/32" 5/32" 15/64" I 1 1/64" 114" 11 164'' MAINTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection or ma
ページ9に含まれる内容の要旨
ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner, 0 Magnetic socket bit Front cap Part No. I Size Part No. I Size 784803-7 114" 3221 24-5 114'' 784805-3 I 7/16" , 3221 20-3 0 Phillips bit Slotted bit Part No. Size Part No. I Size
ページ10に含まれる内容の要旨
May-28-'93 US SCREWDRIVER Model 6805BV Note: The switch, noise suppressor and other part configurations may differ from country to country. 10
ページ11に含まれる内容の要旨
MODEL 6805BV May-28-'93 US DESCRIPTION DESCRIPTION 1 1 32 1 Flat Washer 14 Front Cap 12 2 1 0 Ring 20 33 1 Compression Spring 13 6 3 1 34 3 Steel Ball 5 6 AdiuSf Sleeve 4 1 Ring Spring 22 35 1 Urethane Washer 14 36 1 5 1 Clutch Cover Flat Washer 14 6 1 0 Ring 34 37 1 Ball Rearing 608LB 7 1 38 1 Fan 52 Flat Washer 36 8 1 Ring 36 39 1 ARMATURE ASSEMBLY 9 1 lWlth Item 37 401 Steel Ball 4 10 1 Compression Spring 4 40 1 Ball Bearing 627LB 11 2 Pan Head Screw M5x50 [With Washerl 41 1
ページ12に含まれる内容の要旨
P MAKlTA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective workmanship or ma
