ページ1に含まれる内容の要旨
PS-PRO II - PO W E R C O N D I T I O N ER / SEqu ENCER
ページ2に含まれる内容の要旨
PS-PRO II - PO W E R C O N D I T I O N ER / SEqu ENCER FEa Tu RES INTRODu CTION n SMP+ (Series Multi-Stage Protection Thank you for purchasing the PS-PRO II, and congratulations on your choice. The Series II Plus) non-sacrificial surge suppression power conditioners feature Furman’s revolution- — the most comprehensive protection ary Series Multi-Stage Protection Plus (SMP+) available anywhere! circuit, as well as our exclusive Linear Filtering n LiFT (Linear Filtering Technology) with
ページ3に含まれる内容の要旨
PS-PRO II - PO W E R C O N D I T I O N ER / SEqu ENCER is particularly suited to applications where large l IFT (linear filtering installations must be switched by inexperienced technology ) personnel. The PS-PRO II is controlled by a front panel Unfortunately, traditional AC filter - conditioners key-operated switch to provide security from have been designed for unrealistic laboratory non-authorized users tampering with the sys- conditions. Prior technologies, whether multiple tem. Th
ページ4に含まれる内容の要旨
PS-PRO II - PO W E R C O N D I T I O N ER / SEqu ENCER Although 20 amps is an absolute limit, the front panel Delay Adjust control. PS-PRO II will allow you to come as close as The Delay Adjust control, which can be set us- possible to using the full 20 amps, because ing a screwdriver, controls the total delay time with power sequencing, the risk of tripping between Delay 2 and Delay 3. For example, if the breaker is greatly reduced. The PS-PRO the Delay Adjust is set for 30 seconds, the
ページ5に含まれる内容の要旨
PS-PRO II - PO W E R C O N D I T I O N ER / SEqu ENCER terminals (PCB REV D and later) labeled as: local control only, and a jumper is installed on JMP1 with no switch connected to the PS- JMP1 (Default) (MAINT ON) , when the REM and PRO II’s terminal strip, then a jumper should +12V terminals are tied together, the PS-PRO II be connected between the REM and +12V will sequence OFF. terminals. Otherwise, turning the front panel JMP2 (MOMENTARy ), when the REM and +12V key switch to the REM
ページ6に含まれる内容の要旨
PS-PRO II - PO W E R C O N D I T I O N ER / SEqu ENCER FRONT PaNEl faults—for example, accidental connection to REaR P aNEl lIHT g SWITCH: All Series II 220V. units feature a rear rack BNC socket which will accept any 12 VAC (0.5A) gooseneck lamp as- The PS-PRO II senses voltages that are so high or sembly, (such as the Furman GN-LED or GN
ページ7に含まれる内容の要旨
PS-PRO II - PO W E R C O N D I T I O N ER / SEqu ENCER bined steady-state current drawn by all devices plugged into the unit at any time exceed 20 POWER STa TS u (DEla Y) EDs: l One green amps, the circuit breaker will trip, cutting off LED is provided for each of the three delay power to your rack. If this occurs, reduce the stages. Each LED lights when power is applied load by unplugging one or more units from the to its corresponding duplex outlet on the rear PS-PRO II, and reset it
ページ8に含まれる内容の要旨
PS-PRO II - PO W E R C O N D I T I O N ER / SEqu ENCER NOTE: DO NOT USE the “START ON-OFF (Continued from p.4) SEQUENCE” switch on the front panel in MAINTAINED MODE Maintained Mode . If you do, you may activate an unintended sequence. If a Furman RS-1 is There are 3 maintained modes of operation: the controlling switch, contact Furman’s Tech REM to +12V = OFF (jumper plug installed on Support department for the proper wiring JMP1, MAINT ON) diagrams. The connection of the REM terminal t
ページ9に含まれる内容の要旨
PS-PRO II - PO W E R C O N D I T I O N ER / SEqu ENCER The key lock switches on each unit’s front panel CLASS1 will turn off an individual unit that is currently on WIRING without affecting the other units. +12V The STATUS lines work the same in either STATUS mode. Each reflects the true state of the unit’s OPTIONAL STATUS REM outlets and is affected by both the “memorized” LED state and by the key lock switch. A separate GND LED must be used to indicate the status of each PS-PRO II. To a
ページ10に含まれる内容の要旨
PS-PRO II - PO W E R C O N D I T I O N ER / SEqu ENCER ranty, Manufacturer shall authorize Purchaser to FLASHING DELAy 1 INDICATOR return the Product to the Furman factory or to The DELAy 1 LED on a PS-PRO II flashes an authorized Furman repair location. Warranty to indicate that a remote switch is off or not claims should be accompanied by a copy of the connected. In Maintained Mode (JMP1, MAINT original purchase invoice showing the purchase ON’s jumper plug is installed), this will onl
ページ11に含まれる内容の要旨
PS-PRO II - PO W E R C O N D I T I O N ER / SEqu ENCER SERVICE liability or otherwise. Under no circumstances, whether based on this Limited Warranty or Before returning any equipment for repair, please otherwise, shall Manufacturer be liable for in- be sure that it is adequately packed and cush- cidental, special, or consequential damages. ioned against damage in shipment, and that it is Manufacturer’s employees or representatives’ insured. We suggest that you save the original ORAL OR O
ページ12に含まれる内容の要旨
PS-PRO II - PO W E R C O N D I T I O N ER / SEqu ENCER Furman Sound, LLC. 1997 South McDowell Blvd. Petaluma, California 94954-6919 USA Phone: 707-763-1010 Fax: 707-763-1310 Web: www.furmansound.com 03/2006-A E-mail: info@furmansound.com
