ページ1に含まれる内容の要旨
Installation Instructions
For Medium (15-18.5K) + Heavy duty (22-28.5K) Air Conditioner
READ BEFORE INSTALLING UNIT
To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp
edges that may be exposed:
Air conditioners covered in this manual pose an excessive weight hazard. Two or more people are needed to
move and install the unit. To prevent injury or strain, use proper lifting and carrying techniques when moving unit.
Carefully inspect loca
ページ2に含まれる内容の要旨
Installation Instructions 4. Check for anything that could block airflow will not stop proper air flow. 5. Check the available electrical service WARNING Power supply must be the same as that shown on the unit serial nameplate. (See Use & Care Guide for serial plate location.) Power from the power cord. 6. Carefully unpack air conditioner 115V 230V 230V 15A 15A 20A Do not, under any 230V circumstances, cut, 30A remove or bypass the window support brackets) gro
ページ3に含まれる内容の要旨
Installation Instructions Window Mounting Remove Air Conditioner from Cabinet 1 NOTE: Remove any packaging material from cabinet exterior. 1. Pull down on front grille from upper edge. Lift front grille upwards and place to one side. (See FIG.1) 2. Remove filter. To remove, grasp in the middle on each side. Bow filter out to detach top edge from tabs. Once top is free, lift filter up and out. FIG.2 FIG.1 Front Grille 3. Locate the four Front Panel screws and remove. These screws will be
ページ4に含まれる内容の要旨
Installation Instructions T TOP P “I WINDOW TAINER P Place Cabinet in Window 4 FIG.11 1 For wooden window: Y For Vinyl-Clad window: A FIG.13A FIG.13B FIG.12 B HEX-HEAD SCREW C Install Support Bracket 5 T T . FIG.15B FIG.14 SCREWS AT T RT FIG.15A 4
ページ5に含まれる内容の要旨
Installation Instructions Extend Window Filler Panels and attach to top angle rail: 6 1. Carefully raise window to expose filler panel locking screws on top angle rail. Loosen screws so filler panels slide easily. 2. Extend panels to fill window opening completely. Tighten locking screws on top (FIG. 16). 3. Close window behind top angle rail. 4. HEX-HEAD locking screw through the hole in the middle of top angle rail into the window frame as shown (FIG. 17). FIG.16 FIG. 17 LOCKING SCREWS
ページ6に含まれる内容の要旨
Installation Instructions Thru-The-Wall Installation NOTE: Select Wall Location 1 This air conditioner slides out from its cabinet, so that it can be installed through an outside wall as explained below. NOTE: IMPORTANT: Side louvers must never be blocked. All parts needed for Thru-The-Wall Installation are provided, except a wood frame, shims, and 10 wood screws Prepare Wall 2 22,000~28,500BTU 15,000~18,500BTU FIG.1 FIG.2 Y Inside Inside Width X
ページ7に含まれる内容の要旨
Installation Instructions 4. Build a wooden frame with the INSIDE dimensions of your model listed above. (Measure twice remember...) Frame depth should be the same as wall thickness. Fill in the space from the opending to the studs with wood spacers, as shown. 5. Nail frame to spacers to spacers with front flush with dry wall. NOTE: If wall thickness is 8-1/2” or more, add alumimum flashing over bottom of frame opening to assure no water can enter area between inner and outer wall. NAIL SPACER
ページ8に含まれる内容の要旨
Installation Instructions FIG.7 FIG.8 Support bracket Sill angle bracket Wooden strip 6. Install air conditioner into cabinet by following all steps in Step 9 of Window Mounting. OPTIONAL: Caulking and installation of trim on interior wall may be done. You can buy wood from your local lumber or hardware supply. On the outside, caulk opendings around top and sides of cabinet, and all sides of wood sleeve to the opening. NOTE: See Step 5, Item 4 of Window Mounting Instructions for bottom rail se
