ページ1に含まれる内容の要旨
OPERATING INSTRUCTIONS
HS-1200BT
SPEAKER SYSTEMS
HS-1200WT
HS-1500BT
HS-1500WT
TABLE OF CONTENTS
1. SAFETY PRECAUTIONS ........................... 2 8. INSTALLATION .......................................... 5
2. GENERAL DESCRIPTION ......................... 3 9. EQUALIZING BY THE
DIGITAL SIGNAL PROCESSOR ............... 7
3. FEATURES ................................................. 3
10. SPECIFICATIONS ...................................... 8
4. DIMENSIONAL DIAGRAM ......................... 3
ページ2に含まれる内容の要旨
1. SAFETY PRECAUTIONS • Before installation or use, be sure to carefully read all the instructions in this section for correct and safe operation. • Be sure to follow all the precautionary instructions in this section, which contain important warnings and/or cautions regarding safety. • After reading, keep this manual handy for future reference. Safety Symbol and Message Conventions Safety symbols and messages described below are used in this manual to prevent bodily injury and property damag
ページ3に含まれる内容の要旨
Indicates a potentially hazardous situation which, if mishandled, could CAUTION result in moderate or minor personal injury, and/or property damage. When the Unit is in Use • Do not place heavy objects on the unit as this may cause it to fall or break which may result in personal injury and/or property damage. In addition, the object itself may fall off and cause injury and/or damage. • Make sure that the volume control is set to minimum position before power is switched on. Loud noise produce
ページ4に含まれる内容の要旨
5. INPUT TERMINAL SECTION • As the Speakon connector is internally connected in parallel to the screw terminal as shown below, you can use either of the two. • The usable connector (on the cable end) that matches the NEUTRIK NL4MP Speakon is NEUTRIK NL4FX Speakon. • Input terminal connection diagram is as shown below. [Rear] [Input terminal connection diagram] Speaker Speaker Screw terminal Speakon Screw terminal NEUTRIK NL4MP Speakon 6. IMPEDANCE CHANGE [Rear] To change the impedance, u
ページ5に含まれる内容の要旨
8. INSTALLATION 8.1. Installing to a Ceiling or Wall Install the speaker system to a ceiling or wall using the optional mounting brackets shown below. Note Refer to the instruction manual enclosed with the HY-1200 series or HY-1500 series Mounting Bracket for its mounting details. 8.1.1. HY-1200VB, HY-1200VW, HY-1500VB and HY-1500VW Mounting Brackets (For vertical speaker mounting) • These brackets are designed to mount HS series speakers to ceilings or walls vertically. HY-1200VB and HY-
ページ6に含まれる内容の要旨
8.1.4. HY-W0801 and HY-W0801W Wall Mount Brackets (For wall installation, horizontal angle adjustable) Wall Mount Bracket Installing the HS series speaker to a wall in conjunction with the HY-1200 series or HY-1500 series Mounting Bracket permits the speaker's horizontal angle to be adjusted. Mounting Bracket The figure at right shows an example of vertical speaker installation. 8.1.5. Safety wire installation (For speaker fall prevention) When mounting the speaker system to the ceiling or wa
ページ7に含まれる内容の要旨
8.3. Using as a Floor Monitor Notes • When installing the speaker system on slippery floor, put a non-slip mat under the speaker. • Do not kick or stand on the speaker system, as this will damage the speaker. The figure shows the HS-1200 series. 8.4. Attaching the Supplied Rubber Feet Attach the rubber feet in the case of speaker storage or on-floor speaker installation. Datum line Note The rubber foot has a direction (back and forth). Align the datum line on the rubber foot with the posit
ページ8に含まれる内容の要旨
10. SPECIFICATIONS Model No. HS-1200BT HS-1200WT HS-1500BT HS-1500WT Enclosure Sealed type Rated Power Continuous pink noise: 100 W, Continuous program: 300 W Rated impedance 8 Ω 100 V line: 170 Ω (60 W), 330 Ω (30 W), 670 Ω (15 W) 70 V line: 83 Ω (60 W), 170 Ω (30 W), 330 Ω (15 W), 670 Ω (7.5 W) Sensitivity 97 dB (1 W, 1m) 98 dB (1 W, 1m) Frequency Response 70 to 20,000 Hz 60 to 20,000 Hz Crossover Frequency 3 kHz Directivity Angle Horizontal: 90°, Vertical: 40° Speaker Component Low
