ページ1に含まれる内容の要旨
OPERATING MANUAL
MODE D’EMPLOI
MANUAL DE FUNCIONAMIENTO
COOLING MODEL
ROOM AIR CONDITIONER
WALL MOUNTED TYPE
Indoor Unit
MW09C1F
MW12C1F
Outdoor Unit
MR09C1F
MR12C1F
KEEP THIS OPERATION MANUAL
FOR FUTURE REFERENCE
Friedrich Air Conditioning Co.
4200 N. Pan Am
San Antonio, Texas 78218 USA
Tel. (210) 357-4400 Fax (210) 357-4490
Visit us at www. friedrich. com
P/N9314787041
Español Français English
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
Fig. 1 Indoor Unit Fig. 6 Remote Control Unit 1 Operating Control Panel (Fig. 2) H MASTER CONTROL button 2 MANUAL AUTO button I SET TEMP. / SET TIME buttons (+/-) J Signal Transmitter 3 Indicator Lamps (Fig. 3) K TIMER button 4 Remote Control Signal Receiver L FAN CONTROL button 5 OPERATION Indicator Lamp (red) M START/STOP button 6 TIMER Indicator Lamp (green) N SLEEP button If the TIMER indicator lamp flashes when O SET button the timer is operating, it indicates that a P SWING button fault
ページ4に含まれる内容の要旨
FEATURES AND FUNCTIONS SLEEP TIMER MILDEW-RESISTANT FILTER When SLEEP is selected be pressing TIMER button during The AIR FILTER has been treated to resist mildew growth, Heating mode, the air conditioner’s thermostat setting is thus allowing cleaner use and easier care. gradually lowered during the period of operation; during Cooling or Dry mode, the thermostat setting is gradually raised during the period of operation. When the set time is SUPER QUIET OPERATION reached, the unit automatically
ページ5に含まれる内容の要旨
PREPARATION CAUTION! Turn on the Power Take care to prevent infants from accidentally swallowing batteries. In the case of a direct line connection, turn on the circuit When not using the remote control unit breaker. for an extended period, remove the batteries to avoid possible leakage and damage to the unit. If leaking battery fluid comes in contact with your skin, eyes, or mouth, immedi- Load Batteries (R03 / LR03 × 2) ately wash with copious amounts of water, and consult your physici
ページ6に含まれる内容の要旨
OPERATION To Select Mode Operation Press the START / STOP button (Fig.6 M). 1 The indoor unit’s OPERATION indicator lamp (red) (Fig. 3 5) will light. The air conditioner will start operating. Press the MASTER CONTROL button (Fig.6 H) to se- 2 lect the desired mode. Each time the button is pressed, the mode will change in the following order. s s s AUTO COOL DRY t FAN Example: When set to COOL. About three seconds later, the entire display will reappear. To Set the Thermostat Press the SET TEMP.
ページ7に含まれる内容の要旨
OPERATION About Mode Operation AUTO: Depending on the room temperature at the time operation begins, the During Cooling/Dry mode: operating mode will be switched automatically as shown in the Set the thermostat to a temperature set- accompanying table. ting that is lower than the current room Also, depending on the operating mode, the room temperature set- temperature. The Cooling and Dry modes will not operate if the thermostat is set ting will cause the “standard” temperature to be set as sh
ページ8に含まれる内容の要旨
TIMER OPERATION Before using the timer function, be sure that the Remote Control Unit is set to the correct current time, see page 4. To Use the ON timer or OFF timer To Cancel the Timer Press the START / STOP button (Fig. 6 M). Use the TIMER button to select “TIMER 1 RESET.” (if the unit is already operating, proceed to step 2). The air conditioner will return to normal The indoor unit's OPERATION Indicator Lamp (red) (Fig. 3 5) will light. operation. To Change the Timer Settings Press the TIME
ページ9に含まれる内容の要旨
SLEEP TIMER OPERATION Unlike other timer functions, the SLEEP timer is used to set the length of time until air conditioner operate is stopped. To Use the SLEEP Timer To Cancel the Timer: While the air conditioner is operating or stopped, press the Use the TIMER button to select “TIMER RESET”. SLEEP button (Fig. 6 N). The air conditioner will return to normal The indoor unit’s OPERATION Indicator Lamp (red) (Fig. 3 5) lights and the TIMER operation. Indicator Lamp (green) (Fig. 3 6) light. To St
ページ10に含まれる内容の要旨
ADJUSTING THE DIRECTION OF AIR CIRCULATION Vertical (up-down) direction of airflow is adjusted by pressing the Remote Control Unit’s SET button. Horizontal (right-left) airflow direction is adjusted manually, by moving the Air Flow Direction Louvers. Whenever making horizontal airflow adjustments, start air conditioner operation and be sure that the vertical air direction louvers are stopped. Vertical Air Direction Adjustment R DANGER! Never place fingers or foreign objects in- Press the SE
ページ11に含まれる内容の要旨
SWING OPERATION Begin air conditioner operation before performing this procedure. To select SWING Operation Press the SWING button (Fig. 6 P). The SWING indicator lamp (orange) (Fig. 3 8) will light. In this mode, the Air Flow Direction Louvers will swing automatically to direct the air flow both up and down. To Stop SWING Operation Press the SWING button (Fig. 6 P) once again. The SWING indicator lamp (orange) (Fig. 3 8) will go out. Airflow direction will return to the setting before swing was
ページ12に含まれる内容の要旨
CLEANING AND CARE Before cleaning the air conditioner, be sure to turn off the power supply to the air conditioner. CAUTION! Make sure the plasma filter unit is properly mounted before cleaning or performing other tasks on it. If the unit is not properly mounted, it could fall off and cause damage or injury. You can be injured if you touch the heat exchanger when removing or installing the plasma filter unit. Do not insert your fingers between the plasma filter unit and the heat exchanger
ページ13に含まれる内容の要旨
TROUBLESHOOTING In the event of a malfunction (burning smell, etc.), immediately stop operation, disconnect the WARNING! Power Supply Plug, and consult authorized service personnel. Merely turning off the unit’s power switch will not completely disconnect the unit from the power source. Always be sure to disconnect the Power Supply Plug or turn off your circuit breaker to ensure that power is completely off. Before requesting service, perform the following checks: Symptom Problem See Page Doesn’
ページ14に含まれる内容の要旨
TROUBLESHOOTING Symptom Items to check See Page Is the Power Supply Plug disconnected its outlet? CHECK ONCE Doesn’t operate at all: MORE Has there been a power failure? — Has a fuse blown out, or a circuit breaker been tripped? Is the timer operating? 7 - 8 Is the air filter dirty? Air the air conditioner’s intake grille or outlet port blocked? Poor Cooling or Heating Did you adjust the room temperature settings (thermostat) performance: correctly? Is there a window or door open
ページ15に含まれる内容の要旨
OPERATING TIPS Temperature and Humidity Range Cooling/Dry Mode Outdoor temperature About 32 to 115 °F Indoor temperature About 64 to 90 °F Outdoor temperature About 80% or less 68°F or obove If the unit is used for long periods under high-humidity conditions, condensation may form on the surface of Indoor Humidity the indoor unit, and drip onto the floor or other objects Outdoor temperature About 50% or less underneath. below 68°F En-14
ページ16に含まれる内容の要旨
SOMMAIRE PRÉCAUTIONS DE SÉCURITÉ ............................ Fr-1 RÉGLAGE DE LA DIRECTION CARACTÉRISTIQUES ET FONCTIONS .............. Fr-2 DU FLUX D’AIR .................................................... Fr-9 NOMENCLATURE DES ORGANES..................... Fr-3 FONCTIONNEMENT OSCILLANT..................... Fr-10 PRÉPARATIFS ...................................................... Fr-4 FONCTIONNEMENT FONCTIONNEMENT ............................................ Fr-5 MANUEL-AUTOMATIQUE .............
ページ17に含まれる内容の要旨
CARACTÉRISTIQUES ET FONCTIONS FONCTIONNEMENT TEMPORISÉ FILTRE RÉSISTANT ÀUX MOISISSURE Lorsque le mode SLEEP est sélectionné en appuyant sur le Le Filtre à air a reçu un traitement anti-moisissure, ce qui bouton TIMER en mode Chauffage, la réglage du thermos- assure sa propreté et la facilité de son entretien. tat du climatiseur est progressivement abaissé; en revan- che, en mode Refroidissement, le réglage du thermostat est progressivement élevé. Quand la durée programmée pour FONCTIONNEMENT SU
ページ18に含まれる内容の要旨
NOMENCLATURE DES ORGANES Fig. 1 Unité intérieur Fig. 6 Télécommande 1 Panneau de contrôle de fonctionnement H Touche de contrôle principal (MASTER (Fig. 2) CONTROL) 2 Bouton manuel-automatique I Touches SET TEMP (réglage de la tem- (MANUAL AUTO) pérature)/SET TIME (réglage de l'heure) ( ) 3 Voyants (Fig. 3) J Emetteur du signal 4 Récepteur du signal de télécommande K Touche SET TIMER (réglage de la minu- 5 Voyant rouge de fonctionnement terie) (OPERATION) (rouge) L Touche de contrôle de ventilat
ページ19に含まれる内容の要旨
PRÉPARATIFS ATTENTION! Mise sous tension Prenez soin de ne pas laisser des piles à la portée des petits enfants qui pourraient les Dans le cas d'un branchement direct, enclenchez le dis- avaler par accident. 1 joncteur. Si vous prévoyez de ne pas utiliser la télé- commande pendant longtemps, retirez-en les piles pour éviter un suintement de leur électrolyte. Mise en place des Piles (R03/LR03 × 2) Si de l’électrolyte des piles entre en con- tact avec la peau, les yeux ou les muqueu- ses, l
ページ20に含まれる内容の要旨
FONCTIONNEMENT Sélection du mode de Fonctionnement Appuyez sur la touche START/STOP (Fig. 6 M). 1 Le voyant rouge de fonctionnement OPERATION (Fig. 3 5) de l’apparell intérieur s’allume. Le climatiseur se met en marche. Appuyez sur la touche MASTER CONTROL (Fig. 6 H) 2 pour choisir le mode souhaité. A chaque pression de la touche, le mode change dans l’ordre suivant: s s AUTO COOL DRY (Automatique) (Refroidissement) (Déshumidification) FANt (Ventilation) Après trois secondes environ, l’affichag
