ページ1に含まれる内容の要旨
OWNER'S MANUAL
SPLIT AIRCONDITIONING SYSTEM
MODEL #:
DSB-122L/DSB-122LH
S1
ページ2に含まれる内容の要旨
SAFETY INSTRUCTIONS PLEASE READ THE FOLLOWING SAFETY INSTRUCTIONS BEFORE IN- STALLING AND OPERATING THE UNIT: This air conditioner meets strict safety and operating Precautions When Wiring: standards. The installer of this unit must install or service • Do not plug in the unit until all connections (tubing, this unit so it operates safely and efficiently. drain hose, mounting, etc.) have been made and dou- ble-checked. • High voltages are present in this unit and are very dan- IMPORTANT NOTES ge
ページ3に含まれる内容の要旨
CONTENTS It is recommended that you read the Installation and Operating instructions fully before installing and/or operating this unit. Safety Instructions ...........................................................................................................................................................1 Contents...........................................................................................................................................................................2 Basic
ページ4に含まれる内容の要旨
BASIC ACCESSORIES This Installation section explains how and where to connect this new air conditioner. Please read make sure all acces- sories are included as shown below and read manual thoroughly. This Installation section is provided to assist the per- son knowledgeable in air conditioner installation and should not be installed by anybody who is not thoroughly familiar with this type of installation. Please contact a professional installer if necessary. ACCESSORIES SUPPLIED WITH THE UNIT: 3
ページ5に含まれる内容の要旨
OPTIONAL ACCESSORIES ACCESSORIES NOT SUPPLIED WITH THE UNIT: 3 1 2 4 5 6 7 8 (DSB-122LH Only) No. Description Part No. Qty Material Size 1 Drain Hose Extension 3103200200 1 PVC ID19.6 X 2m PVC Pipe 2 Tape 2TQ1008000 1 PVC 80W X 0.1T X 3.5m 3 Copper Tubing Extension 3100002600 1 1/2", 1/4" Copper Tube 4 Insulator Plate 3103301000 1 F-US 225 X 120 X 8T 5 Putty 2221040001 1 80g 2 6 Connection Cord 3102797200 1 (1.5mm X 6m X 3P) 2 7 Signal line Cord 3102796360 1 (1.5mm X 6m X 2P) 8 Cap Wall 3100900
ページ6に含まれる内容の要旨
TEMP. ON/OFF FAN DIR. MODE FAN SPEED SLEEP TIMER RESET ON OFF ENTER CANCEL LOCATION OF CONTROLS INDOOR UNIT Indoor Cover Air In Deodorizing Filter Removes bad smells from the air. Remote Controller Storage Electrostatic Filter Connection Cover Removes dust Remove cover to access particles from the air. the AC connection from this unit to the outdoor unit. Air Cleaning Filters Removes dust and Cold Air Sensor Wire prohibits germs. (DSB-122LH Only) Indicators Fan Direction Indicate the setting (U
ページ7に含まれる内容の要旨
INDOOR UNIT Indoor Unit Display Switch Panel Remote Control Signal Receiver This place is the part to receive the signal if it receive EMERGENCY REMOTE EMERGENCY REMOTE the signal, you can hear the signal “beep”. ON AIR QUICK TIMER CLEAN When the remote controller is lost or out- of-order, push the emergency button (EMERGENCY) to operate by hand. Timer (Green) ON (Red) Open the front panel on emergency operating. Lights-on during the time Lights-on of reservation mode. during the operation
ページ8に含まれる内容の要旨
DSB-122L REMOTE CONTROLLER AUTO Display Displays information pertaining to unit. ON/OFF Button Press to turn the unit on or off. TEMPERATURE Buttons Press to raise or lower FAN SPEED Button the desired temperature. Press to select the fan speed (High " ", Middle " ", MODE FAN SPEED FAN DIR. Low " ", Natural). FAN DIR. Button SLEEP TIMER Press to select up/down MODE Button direction for fan. Press to cycle through the modes ON/OFF ENTER/ TURBO/MILD CANCEL (Auto/Quick/Cool/Fa
ページ9に含まれる内容の要旨
DSB-122LH REMOTE CONTROLLER AUTO Display Displays information pertaining to unit. ON/OFF Button Press to turn the unit on or off. TEMPERATURE Buttons Press to raise or lower FAN SPEED Button the desired temperature. Press to select the fan speed (High " ", Middle " ", Low " ", FAN DIR. Button MODE FAN SPEED FAN DIR. Natural) Press to select up/down direction for fan. MODE Button SLEEP TIMER Press to cycle through the modes (Auto/Quick/Cool/Fan/Dehumidifier TURBO/MILD /Heat) ON/OF
ページ10に含まれる内容の要旨
TEMP . ON /OFF FAN D IR . MODE FAN SPEED S LEEP TIMER RESE T ON OFF EN TER CANCE L OPERATION CONNECTING THE AC CORD The outdoor unit is connected to the indoor unit through the AC connecting wire or connection cord. To connect the in- door unit to AC, follow the procedures below: 1. Insert the at- NOTES: tached AC plug AC Outlet • Never connect the AC line cord plug to other than the into a pronged and Plug specified voltage (220V). 220V AC outlet. • Use the attached power cord only. • The new a
ページ11に含まれる内容の要旨
HOW TO INSTALL BATTERIES To install the batteries, follow the procedures below: TIMER 1. Slide down the cover to access 2. Insert two “AAA” size ON/OFF ENTER/ TURBO/MILD most of the remote buttons. Slide Alkaline batteries fol- CANCEL down further to access the bat- lowing the polarity dia- tery compartment. gram below. – + BATTERY PRECAUTIONS The precautions below should be followed when using batteries in this device: 1. Use only the size and type of batteries specified. 2. Be sure to fol
ページ12に含まれる内容の要旨
TO SET AUTO MODE This unit will automatically operate the unit according to its surroundings while in the Auto mode. All you have to set is the desired temperature and it will control the fan, coolness and dehumidifier. Follow procedures below: 1.Press the ON/OFF button on the remote control to AUTO 2. Make sure the AUTO indicator appears in the remote turn the unit on; the On LED will light on the indoor display. Using the TEMP. or buttons, set the desired unit and “ON” will light in the temp
ページ13に含まれる内容の要旨
TO SET FAN ONLY MODE To operate only the fan so the unit will circulate the air, proceed as follows: 1.Press the ON/OFF button on the remote control to 2.Press the MODE button until the Fan indicator turn the unit on; the On LED will light on the indoor appears in the display. unit and “ON” will light in the remote display. No allowance setting temperature 3.To select a fan speed, press the FAN SPEED button until the desired speed appears in the display (see be- low). FAN SPEEDS NOTE: “” The fa
ページ14に含まれる内容の要旨
TO SET HEAT MODE (DSB-122LH ONLY) To set the unit to heat the room to a desired temperature, follow the procedures below: 1.Press the ON/OFF button on the remote control to 2.Press the MODE button until the Heat indicator turn the unit on; the On LED will light on the indoor appears in the display. unit and “ON” will light in the In the heat mode, the fan direction remote display. or is further downward than that in the cool mode for the good circulation. 4. To select the fan speed, press t
ページ15に含まれる内容の要旨
TO SET ON TIMER MODE This unit can be set to automatically turn on after a predetermined amount of hours (up to 24) in the order of 0.5, 1, 1.5, 2, 2.5, 3, 3.5, 4, 5, 6, 8, 10, 12, 16, 20, 24. 1.Press the ON/OFF button of timer on the remote control to set the on timer mode, “HOUR” and “ON” on the remote display will be displayed and “TIMER” will be flicked. When you increase to press “ON/OFF” you will get desired time. Then, if pressing “ENTER/CANCEL” button, ON TIMER Mode will be started. If y
ページ16に含まれる内容の要旨
TO SET UNIT TO SLEEP MODE When you are going to sleep, select this feature and the unit will cool off the room to the desired temperature and then increase that temperature throughout the night. 1. Press the ON/OFF button on the 2.Press the MODE button to select the remote control to turn the unit desired mode. Then, set the desired on; the On LED will light on the temperature using the TEMP. or indoor unit and “ON” will light in buttons. the remote display. Press the SLEEP button on the re- 3
ページ17に含まれる内容の要旨
CHANGING/CLEANING THE AIR FILTERS To change or clean the two black air filters, follow the procedures below: 1.Open the indoor unit’s 2.Remove the two small cover and remove both filters (Deodorizing and black air filters by bending Electrostatic) from the them slightly backward indoor unit. and the lifting out. 3.Examine the filters and determine if they need to be 4.Insert cleaned or new cleaned or replaced. To clean filters, use a vacuum and small filters (Deodorizing clean off dust. Use wate
ページ18に含まれる内容の要旨
CARE AND MAINTENANCE warning • Make sure the AC cord is unplugged and the unit is off before cleaning. • Do not use water on the unit to clean it. This is a shock hazard and the unit can be damaged. Clean the casing and front of the indoor unit with a vacuum brush or wipe with a clean damp cloth. • NEVER USE Solvents, harsh chemicals or hot water to clean the unit. • Some metal edges on the unit are sharp. Be careful when cleaning or handling. • Internal parts in the outdoor unit may need cleani
ページ19に含まれる内容の要旨
TROUBLESHOOTING GUIDE Before requesting service, please refer to the chart below for possible solutions: SYMPTOMS POSSIBLE CAUSE POSSIBLE SOLUTIONS No power . Power failure. Restore the power Line voltage too low. Contact electrician to install new outlet. Unit is unplugged or not completely Insert plug all the way. plugged in. Unit is off. Turn unit on. Batteries in remote are weak or dead. Replace remote’s batteries. EMERGENCY/REMOTE Slide EMERGENCY/REMOTE switch is not set to REMOTE. to REMOT
ページ20に含まれる内容の要旨
SPECIFICATIONS MODEL DSB-122L DSB-122LH Function Cooling Cooling / Heating (Heat pump) Power Supply AC 220-240V, 50Hz Cooling Capacity (Heating Mode) 3,024 Kcal/h 3,150 Kcal/h (3,402 Kcal/h) Operating Current (Heating Mode) 5.7A 7.0 A (6.3 A) Power Consumption (Heating Mode) 1,250W 1,500 W (1,410 W) Indoor Unit Dimensions W 925 x H 285 x D 194 mm Outdoor Unit Dimensions W 666 x H 552 x D 264 mm Indoor 9.7 kg Net Weight Outdoor 34 kg Type Flare Connection Gas 1/2" (12.7 mm) the piping Liquid 1/4"
