ページ1に含まれる内容の要旨
PROFESSIONAL MOVING HEAD
USER’S MANUAL
DESIGN WASH 250
ページ2に含まれる内容の要旨
KEEP THIS MANUAL FOR FUTURE NEEDS For your own safety, please read this user manual carefully before installing the device. K eep thi s device aw ay f rom rain and moisture ! U nplug mains lead bef ore openi ng the housi ng. Every person involved with the installation, operation and maintenance of this device has to: -be qualified -follow carefully the instructions of this manual INTRODUCTION: Thank you for having chosen this professional moving head. You will see you have acq
ページ3に含まれる内容の要旨
• dimmer intensity: 0%~100% • auto programs 8 pre-built programs can be selected • lamp on/off control lamp on/off by DMX512 controller • display : can turn 180° if the mounting location so requires • local or remote resetting • lamp switches ON/OFF locally • auto test for all functions • value of each DMX-channel can be displayed • save program: edit and save the program to the incorporated EEPROM through the front control panel or external controller can save maximum 48 scenes, and
ページ4に含まれる内容の要旨
Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle the power cord by the plug. Never pull out the plug by tugging the power cord. During initial start-up some smoke or smell may arise. This is a normal process and does not necessarily mean that the device is defective, it should decrease gradually. CAUTION Never touch the device during operation! The housing may heat up CAUTION Never look directly into the light source, as sensitiv
ページ5に含まれる内容の要旨
For safety reasons, please be aware that all modifications on the device are forbidden. If this device will be operated in any way different to the one described in this manual, the product may suffer damages and the guarantee becomes void. Furthermore, any other operation may lead to short-circuit, burns, electric shock, lamp explosion, crash, etc. INSTALLATION INSTRUCTIONS a) Installing or replacing the lamp CAUTION Only install the lamp with the device unplugged from the mains.
ページ6に含まれる内容の要旨
2) Carefully insert the lamp into the socket. Please remember there is only one way to insert the lamp. Gently slide the lamp and its lamp holder back into place. 3) On the access plate there are 3 screws marked 1,2 and 3.which are used to adjust the lamp holder in the lamp housing. You can adjust the 3 screws to fine-turn the position of the lamp to get the maximum light output as shown below. A B Please remember the lamp is not a hot-restrike type, you must wait for approximately 15
ページ7に含まれる内容の要旨
CAUTION Before taking into operation for the first time, the installation has to be approved by an expert. Cautions: The effect should be installed outside areas where persons may reach it, walk by or be seated. CAUTION When installing the device, make sure there is no highly inflammable material within a distance of min. 0,5m Overhead mounting requires extensive experience, including amongst others calculating working load limits, installation material being used, and peri
ページ8に含まれる内容の要旨
installation via the Omega holders Screw one clamp each via a M12 screw and nut onto the Omega holders. Insert the quick-lock fasteners of the first Omega holder into the respective holes on the bottom of the device. Tighten the quick-lock fasteners fully clockwise. Install the second Omega holder. Pull the safety-rope through the holes on the bottom of the base and over the trussing system or a safe fixation spot. Insert the end in the carabine and tighten the safety screw. DMX-512 co
ページ9に含まれる内容の要旨
DMX-512 connection with DMX terminator For installations where the DMX cable has to run a long distance or is in an electrically noisy environment, such as in a discotheque, it is recommended to use a DMX terminator. This helps in preventing corruption of the digital control signal by electrical noise. The DMX terminator is simply an XLR plug with a 120 Ω resistor connected between pins 2 and 3,which is then plugged into the output XLR socket of the last fixture in the chain. Please see
ページ10に含まれる内容の要旨
If you set a different address, each unit will start to “listen” to the channel number you have set, based on the quantity of control channels of the unit. That means changing the settings of one channel will affect only the selected fixture. In the case of the spot head, which is a 16 channel fixture, you should set the starting address of the first unit to 1, the second unit to 17 (16+ 1), the third to 33 (17 + 16), and so on. Note: The modes of DMX 512 data and lamp are shown via th
ページ11に含まれる内容の要旨
Default settings shaded VALU A001~A5XX (AXXX) DMX address setting ADDR SLAV ON/OFF (SLAV) Slave setting ALON (AU-A) Automatic Run in Stand Alone AUTO MAST (AU-M) Automatic Run as Master RUN Sound-controlled Run in Stand ALON (SO-A) Alone 0 MODE SOUN MAST (SO-M) Sound-controlled Run as Master Display the DMX 512 value of VALU D–XX D-00 (DXXX) each channel DISP RDIS ON/OFF Reverse display CLDI ON/OFF Shut off LED display OPEN ON/OFF Lamp on/off LAAU O
ページ12に含まれる内容の要旨
Main functions: - Main menu 0 1. Press [MODE/ESC] to enter the main menu "MODE" (display flashing) 2. Press [ENTER] and select "ADDR", “RUN” or "DISP" by pressing [UP] or [DOWN] button. 3. Press [ENTER] for selecting the desired sub menu. - DMX address setting, Slave setting - DMX address setting With this function, you can adjust the desired DMX-address via the Control Board. 1. Select “VALU“ by pressing [UP] or [DOWN] button. 2. Press [ENTER], adjust the DMX ad
ページ13に含まれる内容の要旨
- Display the DMX-value, Reverse display, Shut off LED display - Display the DMX 512 value of each channel With this function you can display the DMX 512 value of each channel. 1. Select "VALU" by pressing [UP] or [DOWN] button. 2. Press [ENTER] to confirm; the display shows“D-00”. In this setting, the DMX-adjustment of every channel will be displayed. 3. Press [UP] or [DOWN] button in order to select the desired channel. If you select “D-14” the display will only th show
ページ14に含まれる内容の要旨
2. Press [ENTER], the display shows “ON” or “OFF”. 3. Press [UP] to select “ON” if you wish to enable this function or press [DOWN] button to “OFF” if you don’t. 4. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu. - Lamp automated on with power. With this function you can set the lamp be ignited or not when the fixture is power on. 1. Select “LAAU” by pressing [UP] or [DOWN] button. 2. Press [ENTER], the display shows “ON” or “OFF”. 3. Press [UP] to sel
ページ15に含まれる内容の要旨
4. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu. - Switch 16 bit/8 bit With this function you can switch the device from 16 bit to 8 bit resolution. 1. Select “16BI” by pressing [UP] or [DOWN] button. 2. Press [ENTER], the display shows “ON” or “OFF”. 3. Press [UP] to select “ON” if you wish to enable this function or press [DOWN] button to “OFF” if you don’t. 5. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu. - Pan degree sel
ページ16に含まれる内容の要旨
- Restore factory settings With this function you can restore the factory settings of the device. All settings will be set back to the default values (shaded). Any edited scenes will be lost. 1. Select “LODA” by pressing [UP] or [DOWN] button. 2. Press [ENTER], the display shows “ON” or “OFF”. 3. Press [UP] to select “ON” if you wish to enable this function or press [DOWN] button to “OFF” if you don’t. 4. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.
ページ17に含まれる内容の要旨
- Fixture code and motor fix 1. Select “WHEL” by pressing [UP] or [DOWN] button. 2. Press [ENTER], the display shows “CODE” or “CH01-CH30”. 4. Select “CODE” or “CH01-CH30” by pressing [UP] or [DOWN] button. 5. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu. - Main menu 4 1. Press [MODE/ESC] to enter the main menu (display flashing). 2. Press [UP] or [DOWN] button to select “TIME”. - Fixture running time With this function you can display the runni
ページ18に含まれる内容の要旨
1. Press [MODE/ESC] to enter the main menu (display flashing). 2. Press [UP] or [DOWN] button to select “EDIT”. - Define the number of steps in Run With this function you can define the number of steps in the Program Run. 1. Select “STEP” by pressing [UP] or [DOWN] button. 2. Press [ENTER], the display shows “S-XX”, “X” stands for the total amount of steps you want to save, so you can call up to 48 scenes in “RUN”. For example if the “XX” is 05, it means that “RUN” will run the
ページ19に含まれる内容の要旨
15. Press [MODE/ESC] to exit. The number of steps can be defined under “STEP” and the scenes can be called up under “RUN” b) Editing via the external controller Call up the first scene in your controller now. 1. Select “SC01” by pressing [UP] or [DOWN] button. 2. Press [ENTER], the display shows “SC01”. 3. Press [ENTER], the display shows “C-01”. 4. Select "CNIN" by pressing [UP] or [DOWN] button. 5. Press [ENTER], the display shows "OFF". 6. Press [UP] or [DOWN] button .the displ
ページ20に含まれる内容の要旨
Design Wash 250 DMX channel´s functions and their values (16 DMX channels): Channel 1 - Color Wheel 1 : 0-13 Open / white 14-27 Color 1 28-41 Color 2 42-55 Color 3 56-69 Color 4 70-83 Color 5 84-97 Color 6 98-111 Color 7 112-127 Color 8 128-187 Forwards rainbow effect from fast to slow 188-193 No rotation 194-255 Backwards rainbow effect from slow to fast Channel 2 - Cyan Color Wheel : 0-255 Cyan (0-white, 255-100% Cyan) Channe
