ページ1に含まれる内容の要旨
HD COLOR CAMERA
HDC-900
HDC-900/L
HDC-910
HDC-910/L
HDC-930
HDC-950
HD CCD BLOCK ADAPTOR
HKC-T950
INSTALLATION AND MAINTENANCE MANUAL
1st Edition (Revised 7)
ページ2に含まれる内容の要旨
! WARNING This manual is intended for qualified service personnel only. To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified service personnel. ! WARNUNG Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt. Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die Gefahr eines elektrischen Schlages, F
ページ3に含まれる内容の要旨
For HDC-900/910/930/950 CAUTION ADVARSEL Danger of explosion if battery is incorrectly replaced. Lithiumbatteri - Eksplosjonsfare. Ved utskifting benyttes kun batteri som Replace only with the same or equivalent type anbefalt av apparatfabrikanten. recommended by the manufacturer. Brukt batteri returneres Dispose of used batteries according to the apparatleverandøren. manufacturer’s instructions. Vorsicht! VARNING Explosionsgefahr bei unsachgemäßem Austausch Explosionsfara vid felaktigt batterib
ページ4に含まれる内容の要旨
For the customers in Japan For the customers in the Netherlands Voor de klanten in Nederland Hoe u de batterijen moet verwijderen, leest u in de Onderhoudshandleiding. Gooi de batterij niet weg maar lever deze in als klein chemisch afval (KCA). Für Kunden in Deutschland Entsorgungshinweis: Bitte werfen Sie nur entladene Batterien in die Sammelboxen beim Handel oder den Kommunen. Entladen sind Batterien in der Regel dann, wenn das Gerät abschaltet und signalisiert “Batterie leer” oder nach länger
ページ5に含まれる内容の要旨
Table of Contents Manual Structure Purpose of this manual ........................................................................................ 3 (E) Related manuals................................................................................................... 3 (E) Contents ............................................................................................................... 4 (E) 1. Installation Overview 1-1. Checking before Installation ........................................
ページ6に含まれる内容の要旨
3. Setup Menu 3-1. Setup Menu ...........................................................................................3-1 (E) 3-2. TOP Menu .............................................................................................3-4 (E) 3-3. OPERATION Menu ..............................................................................3-5 (E) 3-4. PAINT Menu .........................................................................................3-7 (E) 3-5. MAINTENANCE Menu ...............
ページ7に含まれる内容の要旨
Manual Structure Purpose of this manual This manual is the installation and maintenance manual of HD Color Camera HDC- 900/910/950/930 and HD CCD Block Adaptor HKC-T950 for HDC-950/930. This manual is intended for use by trained system and service engineers, and is provided information required for the installation and maintenance information . Related manuals Besides this installation and maintenance manual, the following manuals are avail- able. . . . . . HDC-900/910 Operation Manual (Supplied
ページ8に含まれる内容の要旨
... “Semiconductor Pin Assignments” CD-ROM (Available on request) .. This “Semiconductor Pin Assignments” CD-ROM allows you to search for semiconductors used in B&P Company equipment. Semiconductors that cannot be searched for on this CD-ROM are listed in the maintenance manual for the corresponding unit. The maintenance manual contains a complete list of all semiconductors and their ID Nos., and thus should be used together with the CD-ROM. Part number: 9-968-546-XX Contents The installation an
ページ9に含まれる内容の要旨
Section 1 Installation Overview 1-1. Checking before Installation 1-1-1. Checking the ROM and Software Version When connecting the peripheral equipment in the list below to HDC-900/910/950/ 930, be sure to check that the ROM and software version on each peripheral device is corresponding to the camera to be connected. When the HKC-T950 is used by connecting into the HDC-950/930, be sure to check the version of ROM of HDC-950/930. If the ROM and software version is lower than the specified below,
ページ10に含まれる内容の要旨
1-2. Connectors and Cables 1-2. Connectors and Cables 1-2-1. Connector Input/Output Signals HDC-900/910 Connector Layout 1 1 1 !- !- !\ !/ 6 4 3 9 !, 7 8 !; 1 5!] !=![ 1 HDC-900/950 IMM 1-2 (E)
ページ11に含まれる内容の要旨
1-2. Connectors and Cables HDC-950/930 Connector Layout !- 1 7 2 9 * 4 !' !, ![ !. !/ !] 5 !; 8 36!\ * : Use 4 connector by selecting PROMPTER OUT, GENLOCK IN and RET IN signals with the switch. PROMPTER OUT signal become effective when the camera is connected to CCU. GENLOCK IN and RET IN signals become effective when the camera is used alone. HKC-T950 Connector Layout @- @= @] @[ @/ @- @= !\ @\ @[ HDC-900/950 IMM 1-3 (E)
ページ12に含まれる内容の要旨
1-2. Connectors and Cables Input/Output Signals 7 7 7 RET CONTROL (6P FEMALE) 7 7 1 1 1 1 1 CCU connector Based upon BTA S-004A/005A/006A 1.485 Gbps serial Output Signals 2 2 2 EARPHONE OUT (HDC-950/930) 2 2 (External view) EARPHONE mini jack No. Signal I/O Specifications 3 3 3 3 3 TEST OUT 1 INCOM 1 IN Zi > 10 kZ MIC ON/OFF ON : GND BNC type 75 Z, 1.0 V p-p OFF : OPEN 2 INCOM 2 IN Zi > 10 kZ * * * * * 4 4 4 PROMPTER OUT 4 4 MIC ON/OFF ON : GND BNC type 75 Z, 1.0 V p-p OFF : OPEN 3 GND —— 5 5 5
ページ13に含まれる内容の要旨
1-2. Connectors and Cables 9 9 9 REMOTE (8P FEMALE) !- !- !- INTERCOM CH1/CH2 (5P FEMALE) 9 9 !- !- (External view) (External view) No. Signal I/O Specifications No. Signal I/O Specifications 1 TX (+) HDC SERIAL DATA 1 INCOM MIC (Y) IN _20 dBu (CARBON MIC) 2 TX (_) 2 INCOM MIC (X) IN _60 dBu (DYNAMIC MIC) 3 RX (+) HDCU/MSU/RCP/CNU/VCS 3 GND (INCOM/PGM) —— 4 RX (_) SERIAL DATA 4 INCOM OUT 0 dBu RECEIVE 5 TX GND —— GND for TX 5 PGM OUT 0 dBu 6 POWER (+) OUT +26 V, 200 mA (max) (0 dBu = 0.775 Vrms)
ページ14に含まれる内容の要旨
1-2. Connectors and Cables !] !] !] VTR (26P MALE) (HDC-900/910) !] !] !] VTR (26P MALE) (HDC-950/930) !] !] !] !] B 6 B 6 5 5 A 4 A 11 4 3 11 3 10 17 2 10 17 9 2 1 16 9 1 8 16 8 15 22 15 7 14 7 22 21 14 13 21 13 20 20 12 12 19 24 19 18 24 18 23 23 (External view) (External view) No. Signal I/O Specifications No. Signal I/O Specifications A NC No connection A VTR UNREG IN +10.5 to 17 V dc B VTR CMD GND —— GND for VTR CMD B UNREG GND —— GND for UNREG 1 GENLOCK IN Sync 0.6 V p-p, 0 V dc, 1 GENLOCK
ページ15に含まれる内容の要旨
1-2. Connectors and Cables !\ !\ !\ !\ !\ LENS (36P FEMALE) (HDC-900/910) 18 1 36 19 (External view) No. Signal I/O Specifications No. Signal I/O Specifications 1 NC No connection 23 RET 3 ON IN Zi > 10 kZ ON : GND 2 COMMON 5 V IN No connection OFF : High impedance 3 NC No connection * 24 LENS ADRS 0 IN 1 4 +12 V (LENS) OUT +12 V (at 2 A) * 25 LENS ADRS 1 IN 1 5 LENS DC GND —— GND for +12 V (LENS) * 26 LENS ADRS 2 IN 1 6 GND (SIG) —— GND * 27 LENS ADRS 3 IN 1 7 NC No connection 28 EXTENDER 1 OUT
ページ16に含まれる内容の要旨
1-2. Connectors and Cables !\ !\ !\ !\ !\ LENS (12P FEMALE) !; !; !; VF (25P FEMALE) (HDC-900/910) !; !; (HDC-950/930, HKC-T950) 13 12 11 10 9 8 7 6 5 4 3 2 1 25 24 23 22 21 20 19 18 17 16 15 14 (External view) (External view) No. Signal I/O Specifications No. Signal I/O Specifications 1 Y VIDEO (X) OUT 1.0 V p-p, Zo = 75 Z 1 RET VIDEO IN ENABLE : 0 V 2PR VIDEO GND —— GND for PR VIDEO ENABLE DISABLE : +5 V or OPEN 3PR VIDEO (X) OUT 0.7 V p-p, Zo = 75 Z 2 VTR START IN ENABLE : 0 V 4PB VIDEO GND —
ページ17に含まれる内容の要旨
1-2. Connectors and Cables !; !; !; VF (20P FEMALE) (HDC-950/930) !' !' !' EXT I/O (20P) (HDC-950/930) !; !; !' !' 11 5 17 1 18 2 19 3 20 4 16 10 (External view) (External view) No. Signal I/O Specifications No. Signal I/O Specifications 1 S-DA TA IN/OUT TTL level 1 Y VIDEO (X) OUT 1.0 V p-p, Zo = 75 Z 2 NC No connection 2 Y VIDEO (G) —— GND for Y VIDEO 3 NC No connection 3 PROMPTER (X) OUT 1.0 V p-p, Zo = 75 Z 4 SCK OUT TTL level 4 PROMPTER (G) —— GND for PROMPTER 5 NC No connection 5 Pr VIDEO
ページ18に含まれる内容の要旨
1-2. Connectors and Cables !, !, !, TRACKER (FEMALE) !. !. !. FRONT MIC (3P FEMALE) (HDC-950/930) !, !, !. !. 1 2 3 4 5 21 6 7 8 9 10 3 11 12 13 14 15 16 17 18 19 20 (External view) (External view) No. Signal I/O Specifications No. Signal I/O Specifications 1 CHU MIC (G) —— _60 dBu, _50 dBu, _40 dBu, 1 TRK R (X) OUT TRACKER RECEIVE 2 CHU MIC (X) IN _30 dBu, _20 dBu, selectable 0 dBu unbalanced 3 CHU MIC (Y) IN High impedance, Balanced 2 TRK R (G) —— GND for TRACKER R (0 dBu = 0.755 Vrms) 3 GND —
ページ19に含まれる内容の要旨
1-2. Connectors and Cables @[ @[ @[ VF (HKC-T950) @[ @[ (20P FEMALE) (20P FEMALE) 3 2 1 12345 8 7 6 5 4 6789 10 12 11 10 9 11 12 13 14 15 17 16 15 14 13 16 17 18 19 20 20 19 18 (External view) (External view) No. Signal I/O Specifications No. Signal I/O Specifications 1 S DATA IN/OUT TTL level 1 S DATA IN/OUT TTL level 2 NC No connection 2 NC No connection 3 NC No connection 3 NC No connection 4 SCK OUT TTL level 4 SCK IN TTL level MANU : 0 V or OPEN MANU : 0 V or OPEN 5 NC No connection 5 NC No
ページ20に含まれる内容の要旨
1-2. Connectors and Cables @] @] @] CAM BODY (HKC-T950) @\ @\ @\ OPT HEAD (HKC-T950) @] @] @\ @\ (26P MALE) (26P FEMALE) B B 6 6 5 5 A A 4 11 11 4 3 10 17 17 10 3 2 9 16 16 9 2 1 8 15 22 1 22 15 8 7 14 21 21 14 7 13 20 20 13 12 19 24 24 19 12 18 23 18 23 (External view) (External view) No. Signal I/O Specifications No. Signal I/O Specifications A UNREG IN 13 V to 17 V A UNREG OUT 13 V to 17 V B UNREG GND —— GND for UNREG B UNREG GND —— GND for UNREG 1 OHB H OUT 0.3 V p-p Positive pulse 1 OHB H I
