ページ1に含まれる内容の要旨
Installation Instructions / Warranty
Talis
32040XX1
32240XX1
ページ2に含まれる内容の要旨
Talis Lavatory Faucet 32040XX1 Talis Bidet Faucet 32240XX1 32040XX1 32240XX1 Technical Data Caution: Maximum flow rate 2.2 gpm Do not bend or twist Operating pressure: max. 145 psi the supply hoses! Recommended operating pressure: 14.5 - 72 psi Test pressure: 232 psi Hot water temperature: max. 176° F* Recommended hot water temp.: 120° - 140° F* Hole size in mounting surface 1 1/4” Max. mounting surface depth: 1 5/8” 3/8” supply hoses require stops with 3/8” compression fittings (not include
ページ3に含まれる内容の要旨
Installation Flush the hot and cold supplies thoroughly before installing the faucet! Place the faucet and sealing washer on the mount- ing surface. If the mounting surface is less than 3/16” thick, trim the sealing washer so that it is even with the bottom of the mounting surface. From beneath the mounting surface, install the slide washer and collar nut. Tighten the collar nut by hand. slide washer collar nut 3
ページ4に含まれる内容の要旨
Use 3/8” compression fittings (not included) to con- nect the supply hoses to the hot and cold stops. Use two wrenches, as shown in the diagram, to prevent hose twisting. For proper operation of the faucet, the hot supply should be on the left, and the cold supply should be on the right. Install the pop-up drain and pull rod. Turn on the water and check all connections for leaks. If desired, re-set the high temperature limit stop. Install the Pop-up Drain plunger Remove the plunger assem
ページ5に含まれる内容の要旨
Attach the swivel connector to the end of the horizontal rod. Attach the swivel connector to the end of the pull rod. Position as desired and tighten with a small, flathead screwdriver. Re-set the High Temperature Limit Stop (optional) Close the drain or cover it with a wash cloth. Use a 4 mm Allen wrench to push the screw cover into the handle. Retrieve the screw cover when the handle is removed. Use the 4mm Allen wrench to loosen the handle screw 4 complete revolutions. Remove the
ページ6に含まれる内容の要旨
User Instructions Pivot the handle up to turn the water on, down to turn the water off. Pivot the handle to the left for warmer water, to the right for colder water. Replacement Parts 2 1 1.1 3 10 4 6 5 1 handle 32096000 1.1 screw cover 96338000 2 flange 97406000 3 nut 97209000 4 cartridge cpl. 92730000 5 seal 95008000 6 aerator cpl. 13912000 7 fixing set 96016000 8 connection hose 96321001 9 9 pull rod 96657000 10 ball joint 92036000 6 7 8 6
ページ7に含まれる内容の要旨
Cleaning Recommendation for Hansgrohe Products Modern faucetry and shower products utilize a combination of materials to comply with the needs of the market with regard to design and functionality. To avoid damage, it is necessary to use some caution when cleaning. Damage caused by improper treatment is not covered under the Hansgrohe warranty. Cleaning Materials for Faucets and Showers • To remove lime scale, use only products made specifically for that purpose. Always follow the manufactur
ページ8に含まれる内容の要旨
THIS WARRANTY DOES NOT COVER, AND HANSGROHE WILL NOT PAY FOR: A. Conditions, malfunctions or damage not resulting from defects in material or workmanship. B. Conditions, malfunctions or damage resulting from (1) normal wear and tear, improper installation, improper maintenance, misuse, abuse, negligence, accident or alteration, or (2) the use of abrasive or caustic cleaning agents or “no-rinse” cleaning products, or the use of the product in any manner contrary to the product instructions. (3)
