ページ1に含まれる内容の要旨
Installation Instructions / Warranty
ShowerArc
26396001
ページ2に含まれる内容の要旨
ShowerArc 26396001 Minimum ceiling height – 90 1/2” 2
ページ3に含まれる内容の要旨
Installation Considerations • For best results, Hansgrohe recommends on the left and the cold supply must enter that this unit be installed by a licensed, the valve on the right. If the valve is cross- professional plumber. connected, it cannot function correctly. • Please read over these instructions thor- • The difference in water pressure between oughly before beginning installation. the hot and cold supplies should not Make sure that you have all tools and sup- exceed 10 psi or the the
ページ4に含まれる内容の要旨
Installation in 90º corner: Instructions begin on page 5 Wall-to-wall installation Requires 26397000 installation kit (included): Instructions begin on page 13. Roughing-in The ShowerArc requires 1/2” NPT female fittings, recessed 3/8” behind the surface of the finished wall, for the hot and cold water supplies for the thermostatic mixing valve. 4
ページ5に含まれる内容の要旨
Installation in 90º corner Only one set of supplies is required – do not install two sets of supplies. The thermostatic mixing valve may be installed on either wall. This diagram shows both possible positions for the installation. 5
ページ6に含まれる内容の要旨
Installation in 90º Corner Seal the wall around the supplies with waterproof sealant. Failure to seal the wall can lead to possible water damage. 1 2 3 4 6
ページ7に含まれる内容の要旨
5 6 7 8 Seal the wall around the anchors with waterproof sealant. Failure to seal the wall can lead to possible water damage. 7
ページ8に含まれる内容の要旨
9 10 Seal the wall around the anchors with waterproof sealant. Failure to seal the wall can lead to possible water damage. 11 Be careful not to drill into water lines! 12 6 mm 8
ページ9に含まれる内容の要旨
13 14 15 16 9
ページ10に含まれる内容の要旨
17 18 19 20 1 2 6 mm 10
ページ11に含まれる内容の要旨
21 22 Seal the wall around the anchors with waterproof sealant. Failure to seal the wall can lead to possible water damage. 24 23 2 1 6 mm 11
ページ12に含まれる内容の要旨
25 26 Seal the wall around the anchors with waterproof sealant. Failure to seal the wall can lead to possible water damage. Turn to page 22 to continue the installation. 12
ページ13に含まれる内容の要旨
Wall-to-Wall Installation Only one set of supplies is required – do not install two sets of supplies. The thermostatic mixing valve may be installed on either wall. The diagram shows both possible positions for the installation. 13
ページ14に含まれる内容の要旨
Wall-to-Wall Installation Seal the wall around the supplies with waterproof sealant. Failure to seal the wall can lead to possible water damage. 1 2 3 4 14
ページ15に含まれる内容の要旨
5 6 7 8 Seal the wall around the anchors with waterproof sealant. Failure to seal the wall can lead to possible water damage. 15
ページ16に含まれる内容の要旨
9 10 11 12 2 Seal the wall around the anchors with waterproof 6 mm sealant. Failure to seal the wall can lead to possible water damage. 1 Be careful not to drill into water lines! 16
ページ17に含まれる内容の要旨
13 14 Install the 26397000 mounting set 15 16 17
ページ18に含まれる内容の要旨
17 18 90 20 19 XX = XX 18
ページ19に含まれる内容の要旨
21 22 1 2 6 mm 23 24 M6x8 SW 3 mm 19
ページ20に含まれる内容の要旨
25 26 2. M6x8 1. 3. SW 3 mm M6x60 Install the 26397000 mounting set 27 28 2 Seal the wall around the an- 1 chors with waterproof sealant. 6 mm Failure to seal the wall can lead to possible water damage. 20
