ページ1に含まれる内容の要旨
53405 53405 53405 53405 53405 53405
T
E
F
Icons
L
SILICONE
O
TWO HANDLE ROMAN TUB TRIM
LLAVE Y SUS ACCESORIOS
PARA BAÑERA ROMANA DE DOS
MANIJAS (MANERALES)
U
P
C
ACCESSOIRES DE FINITION DE
®
ASME A112.18.1 / CSA B125.1 ROBINET À DEUX POIGNÉES POUR
ICC/ANSI A117.1
BAIN ROMAIN
Model/Modelo/Modéle
T2751 & T4751
™
Dr yden Ser ies/Series/Ser ia
Write purchased model number here.
Escriba aquí el número del modelo comprado.
Inscrivez le numéro de modèle ici.
Y
ページ2に含まれる内容の要旨
Cleaning and Care Backflow Protection System Care should be giv en to the cleaning of this product. Although its finish is e xtremely Y our Delta F aucet hand sho w er incor por ates a bac kflo w protection system that dur ab le , it can be damaged b y harsh abr asiv es or polish. T o clean, simply wipe has been tested to be in compliance with ASME A112.18.3 and ASME A112.18.1/ gently with a damp cloth and b lot dr y with a soft to w el. CSA B125.1. It incor por ates tw o cer tified
ページ3に含まれる内容の要旨
Model / Modelo / Modèle T2751 ▲ Specify Finis h RP54712 1 Red & 1 Blue Handle Button - ▲ Especifíque el Acabad o Not included with model ▲ Précisez le Fini 1 rojo y 1 azul botón de la manija - no proporcionadas con el modelo 1 rouge et 1 b leue bouton de manette - non f our nis a v ec le modèle RP54012 Set Scre w & Button T or nillo de Presión y Botón RP54096▲ Vis de Calage et Bouton Set Scre w & Button T or nillo de Ajuste y Botón Vis de calage et bouton RP52593 Stream Str aight
ページ4に含まれる内容の要旨
A. T4751 B. 1 2 RP40668 Div er ter Assemb ly 3 Ensamb le del Desviador 3 Dér iv ation 2 2 1 1 Maintenance If f aucet leaks from spout outlet–Shut off w ater supplies– Model T4751 A. B. Replace Seats and Spr ings (1). If f aucet does not div er t w ater from the spout to the hand sho w er , chec k that * If leak persists–Shut off w ater supplies– t h e l i f t r o d ( 1 ) i s s e c u r e l y t h r e a d e d i n t o t h e d i v e r t e r ( 2 ) . I
ページ5に含まれる内容の要旨
T2751 T2751 2 1 9 10 7 4 1 1 6 5 8 2 3 T4751 T4751 1 9 10 7 2 4 3/32" 6 (2.38 mm) 1 3/32 po 5 8 2 3 NOTE: The deck and valve rough-in must be finished before Place bases (1) with gask ets (2) o v er end v alv es (3) and secure installing the trim kit. with loc kn ut (4). OPTION: Use silicone under the gasket if deck is uneven. Install gask et (5), base (6) and spout (7) on the spout Model T2751 adapter (8). Be sure spout is resting fir mly on the dec k. Install set Unscre w the test
ページ6に含まれる内容の要旨
T4751 A. T4751 C. 1 3 2 2 3 1 4 3 D. T4751 B. T4751 1 1 2 For Model T4751 Only Slide hose (1) through conical n ut (2). Attach hose (1) to br aided Loosen set scre w (1), remo v e finial (2) from lift rod (3) and install A. C. metal hose (3) using gask et (4) and tighten. DO NO T install hand lift rod. Scre w the lift rod until it drops do wn and rotates freely . piece y et. Reinstall finial (2) and secure with set scre w (1). Install base (1) to nest (2) and tighten. OPTION: Us
ページ7に含まれる内容の要旨
T2751 5 4 1 1 1 T4751 2 1 2 Model T2751 Install handles . Be sure glide ring (1) is properly seated in T ur n f aucet handles (1) all the w a y on. T ur n on hot and cold w ater supplies bottom of handle before installing. If either handle does not and flush w ater lines f or one min ute . Important: This flushes away any rotate in the correct direction, do the f ollo wing: debris that could cause damage to internal parts. 1. Be sure that the end v alv es are installed correctly (wit
ページ8に含まれる内容の要旨
B. T4751 A. T4751 6 2 1 3 1 2 For Model T4751 Only Pull hose (1) to its f ar thest e xtension and point it do wn into the Attach hand piece (1) to hose (2) with gask et (3) betw een A. B. tub . Pull the lift rod (2) up to the full on position and flush w ater connection. Ref er to maintenance section (page 4) f or correct lines f or one min ute . After flushing tur n off w ater at the bath v alv e div er ter and lift rod function. handles . Retur n the lift rod to the do wn po
