ページ1に含まれる内容の要旨
User Guide
English
Nasal Pillows System
ページ2に含まれる内容の要旨
Fitting / Anlegen / Mise en place / Applicazione 1 3 2 Adjustment / Anpassen / Ajustement / Regolazione
ページ3に含まれる内容の要旨
Removal / Abnehmen / Retrait / Rimozione Disassembly / Auseinanderbau / Démontage / Smontaggio 1 2
ページ4に含まれる内容の要旨
Reassembly / Zusammenbau / Remontage / Riassemblaggio 1 2 3
ページ5に含まれる内容の要旨
English ™ AirFit P10 NASAL PILLOWS SYSTEM Thank you for choosing the AirFit P10. This document provides the user instructions for the AirFit P10 and AirFit P10 for Her masks referred to collectively as AirFit P10 throughout this manual. AirFit P10 has blue headgear while AirFit P10 for Her has pink headgear. Using this guide Please read the entire guide before use. When following instructions, refer to the images at the front and back of the guide. Intended Use The AirFit P10 chan
ページ6に含まれる内容の要旨
the device is turned on and functioning properly, new air from the device flushes the exhaled air out through the mask vent holes. However, when the device is not operating, insufficient fresh air will be provided through the mask, and the exhaled air may be rebreathed. Rebreathing of exhaled air for longer than several minutes can, in some circumstances, lead to suffocation. This applies to most models of CPAP or bilevel devices. Follow all precautions when using supplemental oxygen.
ページ7に含まれる内容の要旨
Refer to your CPAP or bilevel device manual for details on settings and operational information. Remove all packaging before using the mask. Using your mask When using your mask with ResMed CPAP or bilevel devices that have mask setting options, refer to the Technical specifications section in this user guide for mask selection options. For a full list of compatible devices for this mask, see the Mask/Device Compatibility List on www.resmed.com on the Products page under Service &
ページ8に含まれる内容の要旨
3. Finally, connect the end of the mask tubing into your device air tubing. Your mask is now fitted and ready to use. When the device is running, a light breeze should be felt through the vent. To inspect the vent place a finger close but not over the entire vent area. Adjustment To achieve a comfortable fit, adjust the split straps by spreading them apart to loosen or draw them closer together to tighten. Removal To take off your mask system, pull the mask and headgear by the spli
ページ9に含まれる内容の要旨
Cleaning your mask at home Your mask and headgear should only be gently handwashed. The mask vent may discolour over time due to dust. Follow the cleaning instructions in this guide to maintain performance and safety of the mask. WARNING Always follow cleaning instructions and use mild soap. Some cleaning products may damage the mask, its parts and their function, or leave harmful residual vapours that could be inhaled if not rinsed thoroughly. CAUTION If any visible deterioration
ページ10に含まれる内容の要旨
When all components including the vent are dry, reassemble according to the reassembly instructions. Weekly: Handwash the headgear in warm (approximately 30°C) water using mild soap. It may be washed without being disassembled. Rinse well and allow it to air dry out of direct sunlight. Reprocessing the mask between patients This mask should be reprocessed when used between patients. Cleaning, disinfection and sterilisation instructions are available from the ResMed website, www.re
ページ11に含まれる内容の要旨
Problem/possible cause Solution Vent is blocked or If the vent requires cleaning, use a dirty/discolored. soft bristle brush. The vent may discolor over time and this is not a safety concern. Follow the cleaning instructions in this guide to maintain performance and safety of the mask. Vent is wet. Ensure the vent is dry after cleaning and in the case of excess condensation. Mask too noisy System is assembled incorrectly. Disassemble the mask, then reassemble according to the instru
ページ12に含まれる内容の要旨
Resistance Drop in pressure measured (nominal) at 50 L/min: 0.4 cm H O 2 at 100 L/min: 1.4 cm H2O Sound DECLARED DUAL-NUMBER NOISE EMISSION VALUES in accordance with ISO 4871. The A- weighted sound power level of the mask is 21 dBA, with uncertainty of 3 dBA. The A-weighted sound pressure level of the mask at a distance of 1 m is 13 dBA, with uncertainty of 3 dBA. Environmental Operating temperature: +5°C to +40°C conditions Operating humidity: 15% to 95% non-condensing Storage and tra
ページ13に含まれる内容の要旨
Symbols The following symbols may appear on your product or packaging: Catalog number Batch code Humidity limitation Temperature limitation Not made with natural Fragile, handle with care rubber latex European Authorised Manufacturer Representative Keep away from rain This way up Indicates a Warning or Caution and alerts you to a possible injury or explains special measures for the safe and effective use of the device Caution, consult accompanying documents. Po
ページ14に含まれる内容の要旨
Mask components / Maskenkomponenten / Composants du masque / Componenti della maschera AirFit P10 AirFit P10 for Her * A Headgear / Kopfband / Harnais / Copricapo 62935 62936 1 Split-strap headgear / Geteiltes Kopfband / Harnais avec sangle à lanière double / Copricapo con cinghia con fenditura 2 Buttonhole / Knopfloch / Boutonnière / Asola 3 Fabric end / Textilende / Extrémité en tissu / Estremità in tessuto B Pillows / Nasenpolster / Coussins / 62930 (XS) 62930 (XS) Cuscinetti 62931 (
ページ15に含まれる内容の要旨
AirFit P10 AirFit P10 for Her * B+C Pillows system / 62920 (XS) 62920 (XS) Nasenpolstermaske / Masque 62921 (S) 62921 (S) narinaire / Cuscinetti nasali 62922 (M) 62922 (M) 62923 (L) 62923 (L) A+B+C Complete system / Komplettes 62901 62911 System / Système complet / Maschera con tutti i componenti XS Extra Small / Extra Small / Très petit / Extra Small S Small / Small / Petit / Small M Medium / Medium / Médium / Medium L Large / Large / Grand / Large
ページ16に含まれる内容の要旨
1 2 3 * * 4 5 6 7 8 Global leaders in sleep and respiratory medicine www.resmed.com 618265/1 2013-10 Manufacturer: ResMed Ltd 1 Elizabeth Macarthur Drive Bella Vista NSW 2153 Australia. Distributed by: ResMed Corp 9001 Spectrum Center Boulevard San Diego CA 92123 USA. ResMed (UK) Ltd 96 Jubilee Ave Milton Park Abingdon Oxfordshire OX14 4RW UK. See www.resmed.com for other ResMed locations worldwide. For patent information, see www.resmed.com/ip. AirFit is a trademark of ResMed Ltd. © 201
