ページ1に含まれる内容の要旨
FPC-8057
5.7” STN LCD, Xscale-based touch screen
computer
User’s Manual
ページ2に含まれる内容の要旨
Disclaimers The information in this manual has been carefully checked and is believed to be accurate. Acnodes Corp. assumes no responsibility for any infringements of patents or other rights of third parties which may result from its use. Acnodes Corp assumes no responsibility for any inaccuracies that may be contained in this document. Acnodes Corp makes no commitment to update or to keep current the information contained in this manual. Acnodes Corp reserves the right to make improvemen
ページ3に含まれる内容の要旨
ESD Precautions Integrated circuits on computer boards are sensitive to static electricity. To avoid damaging chips from electrostatic discharge, observe the following precautions: • Do not remove boards or integrated circuits from their anti-static packaging until you are ready to install them. • Before handling a board or integrated circuit, touch an unpainted portion of the system unit chassis for a few seconds. This helps to discharge any static electricity on your body. • Wea
ページ4に含まれる内容の要旨
Unpacking The FPC-8057 is packed in an anti-static bag. The product has components that are easily damaged by static electricity. Do not remove the anti-static wrapping until proper precautions have been taken. Safety instructions in front of this User’s Manual describe anti-static precautions and procedures. After unpacking the product, place it on a raised surface and carefully inspect the board for any damage that might have occurred during shipment. Ground the product and exercise ext
ページ5に含まれる内容の要旨
Safety Instructions Overview This section states the safety instructions, which must be followed when installing, operating and servicing the FPC-8057. If neglected, physical injury and death may follow, or damage may occur to controller and related equipment. The material in this chapter must be studied before attempting any work on, or with, the unit. Warnings and Notes This manual distinguishes safety instructions. Warnings are used to inform of conditions, which can, if proper steps
ページ6に含まれる内容の要旨
damage equipment. General warning: Warns of situations, which can cause physical injury and or damage equipment by means other than electrical. Electrostatic Discharge Warning: Warns of situations in which an electrostatic discharge can damage equipment. Readers are notified of the need for special attention or additional in formation available on the subject with the following symbols: CAUTION! Aims to draw special attention to it. Note: Note: gives additional information or points out
ページ7に含まれる内容の要旨
Table of Contents Disclaimers --------------------------------------------------------ii ESD Precautions --------------------------------------------------iii Unpacking ---------------------------------------------------------iv Safety Instructions ------------------------------------------------ v Chapter 1 Introduction-------------------------------------------- 1 1.1 General Description .........................................................1 1.2 Features ............................
ページ8に含まれる内容の要旨
2.4 CE Requirements ..........................................................18 2.5 Dimensions of FPC-8057 ............................................. 19 Chapter 3 Windows CE.NET ------------------------------ 21 3.1 Introduction ............................................................... 21 3.2 Utilities ....................................................................... 22 3.2.1 Soft-Keyboard ......................................................... 22 3.2.2 System S
ページ9に含まれる内容の要旨
FPC-8057 User’s Manual Chapter 1 Introduction 1.1 General Description The FPC-8057 series are fan-less and compact-size touch panel computers. It equips with 5.7” STN LCD display, Windows CE.NET and low power consumption CPU, Intel Xscale PXA255. Therefore, FPC- 8057 series are good cost-effective choices for operator interface applications. The FPC-8057 adopts most reliable and stable design. With fan-less CPU and CompactFlash card, FPC-8057 is especially suitable for vibration env
ページ10に含まれる内容の要旨
FPC-8057 User’s Manual 1.2 Features z Fan-less and low power consumption CPU- Xscale PXA255 z 5.7” QVGA color STN LCD z Windows CE.NET supported and flash ROM on-board z Slim and compact size design z Suitable for reliable and vibration application – Fan less and CompactFlash card z NEMA 4 / IP65 compliant front panel z Support Compact Framework z Over-voltage power protection – fuse 1.3 Specifications z Construction: plastic molding housing z Display: 5.7" QVGA Color STN LCD ™ z C
ページ11に含まれる内容の要旨
FPC-8057 User’s Manual LCD Display z Display type: STN color LCD z Display size (diagonal): 5.7" z Max colors: 4096 z Resolution: 320 x 240 z Pixel pitch (HxV, mm): 0.36 x 0.36 z Viewing angle: 100° z Luminance (cd/m2): 150 z Storage temperature: - 20~60°C z Operating temperature: 0~45°C z Backlight: CCFL z Contrast ratio 30:1 Touch screen z Type: 4-wire, analog resistive z Resolution: 320*240 z Light transmission: above 80% z Life: 1 million activation minimal Fuse z BUSSMANN
ページ12に含まれる内容の要旨
FPC-8057 User’s Manual z CE: Complies with EN50081-2 and EN50082-2 standards z Front panel meets NEMA4 / IP65 Introduction 4
ページ13に含まれる内容の要旨
FPC-8057 User’s Manual Chapter 2 Installation Instructions 2.1 Mounting Instructions 2.1.1 Location Considerations Care should be taken when locating equipment behind the unit to ensure that AC power wiring, PLC output modules, contactors, starters and relays, and any other source of electrical interference are located away from the back of the unit. Particular note should be taken to the position of variable speed drives and switching power supplies. Their input and load cables should
ページ14に含まれる内容の要旨
FPC-8057 User’s Manual the unit is secured in the panel. Caution! Do not over tighten mounting clamps! Note: Specifications Note: To seal to NEMA-4 specifications, all supplied mounting clamps must be used and panel cannot flex more than 0.010”. Installation Instructions 6
ページ15に含まれる内容の要旨
FPC-8057 User’s Manual 2.1.3 Environmental Considerations z The FPC-8057 are to be used indoors as built in displays. Make sure that the displays are installed correctly and that the operating limits are followed (See Specifications). z Do not operate the unit in areas subject to explosion hazards due to flammable gases, vapors or dusts. z The unit should not be installed where fast temperature variations and/or high humidity are present. This will cause condensation of water in the dev
ページ16に含まれる内容の要旨
FPC-8057 User’s Manual 2.2 Power Connections Make sure that all local and national electrical standards are met when the installing the unit. Contact your local authorities to determine which codes apply. Installation Instructions 8
ページ17に含まれる内容の要旨
FPC-8057 User’s Manual 2.2.1 Power Requirements The FPC-8057 can be powered by DC power only. The specified voltage range is +21 to 25 Volts DC. This Power insures compatibility with most controller DC systems. The power conditioning circuitry inside the unit is accomplished by a switching power supply. The peak starting current can be as high as 700mA. If the display does not come on within 2 seconds of power up, remove power. An internal fuse will prevent damage if the polarity of
ページ18に含まれる内容の要旨
FPC-8057 User’s Manual common paired with a hot or signal line. If wiring is to be exposed to lightning or surges, use appropriate surge suppression devices. Keep AC, high energy, and rapidly switching DC wiring separate from signal wires. Equip ungrounded DC supplies with a resistor and capacitor in parallel to earth ground. This provides a path for static and high frequency dissipation. Typical values to use are 1MOhm and 4700pF. To make a connection, strip about 3/8” of insulation
ページ19に含まれる内容の要旨
FPC-8057 User’s Manual FUSE Replacement: The fuse use on FPC-8057 is: BUSSMANN Fast Acting, Glass Tube Rating: 250VAC, 1A Size: 5x20mm Warning: Make sure the power off before replace the fuse. Do 1. not replace the fuse with a different rating fuse. 2. 2.2.2 Grounding Requirements Chassis ground must be used. DC ground is not directly coupled to Earth ground internally. It is preferable not to ground DC negative return to chassis ground as poor site earths can introduce noise int
ページ20に含まれる内容の要旨
FPC-8057 User’s Manual 2.2.3 CE Requirements To make a FPC-8057 comply with EMC directives, and to reduce susceptibility to electrical interference, a separate #14 AWG ground wire should be taken to the chassis ground terminal of the power connector. This ground connection should be run directly to the central star earth connection point (as recommended in most Installation Instructions). 2.2.4 Safety Guidelines This section presents recommended installation practices, and procedures. S
