ページ1に含まれる内容の要旨
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
i ELECTRICAL REQUIREMENTS This unit is equipped with a No. 10 ground wire in IMPORTANT if location the conduit. utilizes aluminum wiring: The Connect Io Intelligent Oven requires a separate, grounded 4-wire, 40V (AC), 50 Amp The electrical conduit must be kept to the top left • Connect the aluminum service with its own circuit breaker. for a flush installation. Never cut the conduit. wiring to the copper wire using special connectors designed Wire sizes and connections must conform wit
ページ4に含まれる内容の要旨
Quick Reference PRODUCT DIMENSIONS APPROXIMATE SHIPPING WEIGHT: 350 lbs / 159 kg REFRIGERATION: Oven Right View Oven Rear View Refrigeration ductwork is located at the rear of the oven and must not be damaged during installation. RJ45 network jack 120V outlets INTERNET HOOKUPS: RJ45 (CAT5/Ethernet) network connection is located at the rear of the oven. If a wireless bridge connection is preferred, or if local routers or adaptors are used, then use the 2-socket 120V electrical outlet prov
ページ5に含まれる内容の要旨
ページ6に含まれる内容の要旨
ページ7に含まれる内容の要旨
! WARNING! INSTALLATION STEPS CAUTION: Remove oven door, and remove the THE OVEN SHOULD NEVER BE LAID ON STEP 1. Unpacking the Oven louvered refrigeration panel before removing unit ITS BACK OR SIDE. If the oven has been from shipping pallet. laid on its back or side, the oil in the compressor will need at least one (1) j Make sure to TURN OFF the breaker for the hour to drain back into the compressor oven power supply. Carefully remove all packing before powering up the oven. material
ページ8に含まれる内容の要旨
ページ9に含まれる内容の要旨
Figure 1. INSTALLATION STEPS Option 1: If Connecting to a 4-wire System: Cable from power supply Junction Box STEP . Electrical Connections n Connect the white oven conduit wire to the neutral (white) wire in the junction ELECTRICAL SHOCK White wires box. See Figure 1. ! WARNING! HAZARD! Red wires o Connect the bare grounding oven Turn OFF the household power supply breaker cable wire to the green or bare grounding ! before connecting wires. The oven must be wire in the junction box.
ページ10に含まれる内容の要旨
ページ11に含まれる内容の要旨
INSTALLATION STEPS o IMPORTANT: Securely fasten the oven to the cabinet using the four (qty. 4) Phillips cabinet mounting screws STEP 6. Install Oven Into Cabinet provided. Insert the Phillips screws through holes in the oven vertical side trim. Do not over-tighten screws. ! WARNING! Fuse Holder for 120v convenience outlet When sliding the oven into the cabinet, make OVEN MUST BE SECURED INTO CABINET USING ATTACHMENT TRIM. Failure to do so can result in the sure to place the power cable
ページ12に含まれる内容の要旨
ページ13に含まれる内容の要旨
INSTALLATION STEPS DOOR ATTACHMENT: i STEP . Final Checklist Door hinge Door hinge in locked in unlocked • Place both hinge arms back in the position position slots of the hinge receiver. j Make sure the oven is level, and securely fitted/ attached to the oven cabinetry. • Push the hinge arms in as far as they k Reinstall oven door. See “Door Attachment”. will go until the bottom of the door i meets the frame of the oven. When l Make sure to remove all internal packaging from the insert
ページ14に含まれる内容の要旨
REPLACEMENT PARTS: CLEANING YOUR OVEN MORE INFORMATION Only authorized replacement parts may be used in performing service Cleaning Tips & Precautions Other Tips & References on the Connect Io Intelligent Oven. Do not repair or replace any part OVEN INTERIOR 3 Keep the Connect Io Installation Manual in a of the appliance unless specifically Wash the interior of the Connect Io oven convenient location near the Connect Io Intelligent recommended in the Connect thoroughly with hot, soapy w
ページ15に含まれる内容の要旨
TM TM Connect Io Intelligent Oven Model PS302SS00 Professional Series Refrigerated, Internet Controlled 30” Electric Built-In Double Wall Oven Installation Instructions Part No. 101206 © 2007 TMIO, LLC • +1.800.881.TMIO (8646) • www.tmio.com • 1220A Flynn St. • Chattanooga, TN 37403 USA
