ページ1に含まれる内容の要旨
Index
1. PRECAUTIONS FOR SAFETY AND USE _____________________ 21
2. INSTALLING THE OVEN __________________________________ 23
3. DESCRIPTION OF CONTROLS ____________________________ 25
4. USING THE OVEN_______________________________________ 26
5. CLEANING AND MAINTENANCE ___________________________ 33
6. EXTRAORDINARY MAINTENANCE _________________________ 36
INSTRUCTIONS FOR THE INSTALLER: these are intended for the
qualified engineer
ページ2に含まれる内容の要旨
Presentation 1. PRECAUTIONS FOR SAFETY AND USE THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE. TAKE GOOD CARE OF IT AND KEEP IT TO HAND THROUGHOUT THE OVEN'S LIFE CYCLE. WE URGE YOU TO READ THIS MANUAL AND ALL THE INFORMATION IT CONTAINS CAREFULLY BEFORE USING THE OVEN. INSTALLATION MUST BE CARRIED OUT BY QUALIFIED STAFF IN COMPLIANCE WITH THE RELEVANT REGULATIONS. THIS OVEN IS INTENDED FOR PROFESSIONAL USE AND COMPLIES WITH THE EEC DIRECTIVES CURRENTLY IN FORCE. THE APPLIANCE
ページ3に含まれる内容の要旨
Presentation NEVER PLACE INFLAMMABLE OBJECTS IN THE OVEN: IF IT SHOULD ACCIDENTALLY BE SWITCHED ON, THIS MIGHT CAUSE A FIRE. THE APPLIANCE BECOMES VERY HOT DURING USE. OVEN GLOVES SHOULD ALWAYS BE WORN. THE NAMEPLATE WITH THE TECHNICAL DATA, SERIAL NUMBER AND MARK IS IN A VISIBLE POSITION ON THE BACK OF THE OVEN. THIS NAMEPLATE MUST NEVER BE REMOVED. THE APPLIANCE IS INTENDED FOR PROFESSIONAL USE BY TRAINED STAFF. KEEP CHILDREN AT A SAFE DISTANCE AND NEVER ALLOW THEM TO
ページ4に含まれる内容の要旨
Instructions for the Installer 2. INSTALLING THE OVEN The oven is designed for free-standing installation on a horizontal work- top. It must be far enough from the wall behind it to allow easy access to the terminal board for connection of the power supply lead. Installation must be carried out by a qualified engineer in compliance with the relevant EEC DIRECTIVES. 2.1 Electrical connection (Mod.Alfa 200XE) Check that the power supply voltage and size are as specified on
ページ5に含まれる内容の要旨
Instructions for the Installer 2.2 Safety thermostat The oven is fitted with a safety device tripped in case of a serious malfunction. To reset the safety device, call the after-sales service. The manufacturer declines all responsibility for injury or damage caused by failure to comply with the above regulations or deriving from tampering with even just one part of the appliance. 2.3 Levelling Level the oven by means of its four adjustable feet. To make the adjustment, u
ページ6に含まれる内容の要旨
Instructions for the User 3. DESCRIPTION OF CONTROLS STOP BUTTON Use this button to set the time when turning on the appliance for the first time or after a power failure, scroll through preset programs and terminate cooking cycles. START BUTTON Use this button to set the time when turning on the appliance for the first time or after a power failure, scroll through preset programs and start cooking cycles. DISPLAY Displays the current time, the selected
ページ7に含まれる内容の要旨
Instructions for the User 4. USING THE OVEN 4.1 Precautions and General Advice When the oven is used for the first time, it should be heated to 200°C for long enough to burn off any oily residues left by the manufacturing process. If you have to carry out any procedures on foods, leave the door open for as short a time as possible to ensure the temperature inside the oven does not drop far enough to impair cooking results. To avoid unpleasant contact with any steam insid
ページ8に含まれる内容の要旨
Instructions for the User P5.5 or P3.0 for single-phase power connection. After selecting the appropriate power, press STOP to confirm the setting. N.B. This power setting operation only has to be carried out the first time the oven is connected. The value set is saved and automatically used whenever the oven is switched on after this. To modify this setting or the time, press START + STOP together to return to the point described in section "4.3 Setting the time". 4.6 Program
ページ9に含まれる内容の要旨
Instructions for the User To edit a humidified fan-mode program by entering the parameters exactly as required, turn the knob to one of the programs from P1 to P14. The display shows the parameters contained in the selected program. Hold down STOP for 2 seconds. A beeper sounds to indicate that the editing mode has been accessed, and the message Ut°C appears on the display. Press START to display the cooking temperature. Press START or keep it pressed to increase the cooking te
ページ10に含まれる内容の要旨
Instructions for the User The display shows UEnd. The parameters set are now saved in the chosen program. Press START to display the parameters just set. Press START again to run the program just edited. 4.8 Humidified fan-mode cooking Use the knob to select one of the preset programs (P1 – P14). The display shows the parameters of the selected program. Press START to confirm the start of the program. The program starts, performing the preheating stage; the display shows "Pr
ページ11に含まれる内容の要旨
Instructions for the User N.B. - during preheating and cooking, whenever the door is opened the message "door" will appear on the display and a beep will sound to warn the user that the door must be closed while these operations are in progress. 4.9 Modifying a previously edited program To modify one of the programs, turn the knob to one of the programs from P1 to P14 edited previously. The parameters saved earlier will appear on the display. Hold down STOP for 2 seconds. The d
ページ12に含まれる内容の要旨
Instructions for the User 4.10 Manual cooking Use the knob to select the manual program. The special feature of this user-editable program is that the cooking parameters set are not retained in the memory when the knob is turned to any other position. This means that an "empty" program is always immediately available for quick, easy editing. 4.10.1 How to use this program Use the knob to select the manual program. The display shows "- - - - " to indicate that there are no coo
ページ13に含まれる内容の要旨
Instructions for the User 4.13 Possible error messages on the display 4.13.1 Err1 This message appears whenever the software detects that the sensor connector is not properly connected to the electronic circuit board or has short-circuited. This error resets automatically when the oven’s power supply is switched off. If the error persists, call the After-Sales Service. 32
ページ14に含まれる内容の要旨
Instructions for the User 5. CLEANING AND MAINTENANCE Important: never point jets of water straight at the oven and do not use high- pressure water cleaners. Before carrying out any operation, disconnect the oven from the electricity supply. 5.1 Cleaning stainless steel To keep stainless steel in good condition, it must be cleaned regularly at the end of each day, after allowing it to cool. When cleaning and caring for stainless steel surfaces, al
ページ15に含まれる内容の要旨
Instructions for the User 5.2 Cleaning the inside of the oven To keep the oven in good condition, it must be cleaned regularly at the end of each day, after allowing it to cool. Remove all removable parts. Remove the side runners by lifting them and sliding them off the supporting pins. (as shown here). • Clean the oven shelves and side runners with hot water and non- abrasive detergents, rinse and dry. 34
ページ16に含まれる内容の要旨
Instructions for the User 5.3 Door glazing The pane of glass in the oven door is very easy to clean since the inside window can be opened. This means that each pane of glass can be cleaned on both the inside and the outside. To open the inside pane, simply gently pull out the two points shown in figure 1. After cleaning, to close the inside window simply push it gently towards the door and fit the pins (Fig. 2) into the holes provided. 1) 2) 35
ページ17に含まれる内容の要旨
Instructions for the User 6. EXTRAORDINARY MAINTENANCE Occasionally, the oven will require minor servicing procedures or the replacement of parts subject to wear and tear, such as gaskets, light bulbs, etc. The specific operations for each procedure of this kind are provided below. Before carrying out any operation, disconnect the oven from the electricity supply. 6.1 Changing the light bulb Remove the protective cover A. Replace the bulb B with another of the
