ページ1に含まれる内容の要旨
Range
INSTALLATION
Models SVE47600, SVE47500, mmi_JENN.AIR
403WEST FOURTS HTREET N,ORTH • NEWTON IA , 50208
D INSTRUCTIONS
SVE47100, SCE30600, SCE30500
iNSTRUCTION TO SINSTALLER: "Important: Saveforlocalelectrical inspector's use".
• ALL RANGESCAN TiP AND
CAUSE INJURIES TOPERSONS.
WARNING
Range Overall Dimensions:
Width - 29-15/16" (76.04 cm) _ • INSTALL ANTI-TIP DEVICES
Height - 35-1/2" (90.17 cm)
•Add 2" (5.08 cm) for doorhandle
I
• FOLLOWALL INSTALLATION
INSTRUCTIONS.
Depth - 26-3/8" (70.00 c
ページ2に含まれる内容の要旨
1. UnpackRange (Figure1) • Cut and remove shippingcarton. • Removelowerrangepanelor drawer,andplace outofwork area. • Removeblower package (if you have not already done so.) (Downdraft ModelsOnly.) • LocateDuctingInstruction sheet. (DowndraftModelsOnly.) NOTE:Please read through entire installation instructionsand ducting 1 instructions priorto beginninginstallation. 2. Select Range Location(Figure2) • Carefullyselectthe rangelocation,keepingin mindthefollowing: (Figure 1) A. Over-rangecabinetsa
ページ3に含まれる内容の要旨
5. Slide-In Cutout (Figure5) * Usethe overhangmeasurementto figure the "A"dimension: Overhang 1/2" (1.27cm) to 1" (2.54cm) .... "A" = 22-5/8"(57,47cm) Overhang1" (2.54cm) to 1-3/4" (4.45cm) .... "A" = 23" (55.42cm) . Carefullymarkthe countertopand recheckyour dimensions. • Before you cut, checkthe rear countertopdimensions. (See#6.) NOTE:The minimumclearancebetweenthe cutoutandcabinetdoors and drawer edge is 7/8". 6. Slide-In Cutout (Figure 6) • Check your marked up dimensionscarefully.The rear
ページ4に含まれる内容の要旨
11. Wall VentCutout (Figure11) center to center. II _- _ . WALLSTUD • Willtheventductbe6" (15.24cm) roundthroughthewallor3-1/4" x 10" (8.26cmx 25.4 cm) rectangle,verticatlyinsidethe wall? /" • See DuctingInstructionsfor rearduct insidethe wall. Note: Cutout in the wall must clear3-1/4" x 10" (8.26cm x 25.4 cm)transition elbow. • Locate the closest stud to your proposed vent hole location. Use the r_ (/_._ followingchartto figurethe "X"dimension.Seethe illustrationforthe other dimensions. oceevea
ページ5に含まれる内容の要旨
15. ConnectElectrical (Four ConductorWire) (Figure15) • Removethe range electrical servicecover, located on the back, lower _ ;'_ left-handcorner. • Removethe grounstrapscrewandbendthe strapup as shown.Installa 3/4" (1.91cm) cable clampin the hole provided,belowthe terminal block. I,_NO l c o a esu o. o a.e re ower • Strip 3" (7.62cm)of outer insulationfrom the cable. ,GROUND • Strip 1/2" (1,27cm)of insulationfrom each wire. WIRE • Pullthe cablethroughthe cableclamp. • Make a loopinthe bare grou
ページ6に含まれる内容の要旨
19. Level Range (Figure19) --IL ll • Free-Standing.Adjustthelevelerfeetto levelrangewiththe countertop. • Slide.ln.Adjustthelevelerfeettotakesomeoftheweightoffefthecountertop. • Unit must be level for optimum baking performance.Check levelness inside oven using a level that is placed on oven rack. • Fornon-downdraftunitsgo to step 22. (Figure 19) 20. Connect Blower Electrical (Downdraft Units Only) (Figure20) ,ow_,co,o BLOWER ]lJ • Connectthe blower power cord on the range to the blower (see ill
ページ7に含まれる内容の要旨
_peCial Instructi---onsFor Ven_net Toe S )ace Additional instructionsfor ventingthroughthe base cabinettoe space oneither sideof the rangewhen it isnot possibleto vent throughthe floor or througha rear wall. Additional MaterialsRequired 1.5" Dia.x 19" long (12.7cm x 48.26 cm) Flex Duct* (P/N702935) _ " 1 6" (15.24 cm)90° Elbow Left 31.19" Right • Cabinet 79.22 _ Cabinet 2. HoseClamps*(P/N702331) ! 1 5" to 3-1/4" x 10" (12.7cm to 8.26 cmx 25.4 cm)Transition* _-17.12S",-_ _-17.125"-,_ • 5._o' I (_
ページ8に含まれる内容の要旨
Step4 Attachthe blowerhousingtothefloor withthe outlettoward thedirection Right Side Left Side I of venting andthe inlettoward the front of the cabinets. (See Figures 2 Venting Venting and 3 for specific location.) in addition,for left side venting, a spacer I {erthemountingbracketflanges ofthe blowerassembly.(SeeFigure Step5 _,_proximately1-1/2" thick x 9" long (3.81cm x 22.86 cm)is required __ Removethe inside wire andtheoutsidestringfrom thefirst 1-1/2inches Spacer/ (3.81cm) of oneend of the
ページ9に含まれる内容の要旨
DUCTING FREE-STANDING INSTALLATION c o M _= A N Y SLIDE-IN I GRILL-RANGE MODELS E N N-AI R INSTRUCTIONS 3o3_S.ADEL*ND • ,NO,_NAPOL''N S, 46226 o9ol . DROP-IN k DUCTING MUST CONFORM TO LOCAL CODE MATERIALS AND "MAKE-UP" REQUIREMENTS-- 300 CFM MINIMUM IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE • DUCTING A JENN-AIR GRILL-RANGE IS EASY BUT CRITICAL FOR PROPER PERFORMANCE. • AFTER READING THESE INSTRUCTIONS PLAN THE DUCT RUN. • USE THE 'DUCT LENGTH CHART' TO FIND THE EQUIVALENT LENGTH OF TH
ページ10に含まれる内容の要旨
PLAN THE DUCT RUN 1. Make a sketch of the total system. Identify the type of each fitting and the length of straight pipe. 2. Enter your run into the 'Duct Length Chart' in the next section. Example I Example 2 __ _.5" to 6" Transition to 6" Transition 2' of 6" ound Elbow 2' of 6" Round \ 6" Elbow .6' Elbow 6" Round ' \ 4' of 6" Round )_" 6" Elbow ;"Elbow 4' of 6" Round . 6 of 6 Round 31/4 " X10"Transition 6" WallCap 10'of 3¼"x 10"Straig C,..,. DUCT LENGTH CHART 1. Elbows, wall caps and other fi
ページ11に含まれる内容の要旨
USE TABLE BELOW TO CALCULATE TOTAL SYSTEM DUCT F|TTING TOTAL EQUIVALENT DUCT FITTING EQUIVALENT LENGTH NO. OF FITTINGS LENGTH-FITTING 6" Dia. 90 ° Elbow 5 FL (1.52 m) 6" Dia. 45 ° Elbow 2.5 Ft. (.76 m) 5" to 6" Transilion .._ P/N A456 _m n.owTHZS omECT_0N _OT o27c= to_24 cm} _ _ 1.0 Ft. (,30 rn) RECOI_Eta_tD AIRFLQW 6" tO3%" x 10 " 90_ Elbow (1524 c rn tO8 25 cm X 254 cm) WN A496 5 Ft. (1.52 m) AIR F1-OW 3%" X 10 " to 6" 90" ELBOW {826-cm • 254 cm to 1524 Crn) P/N A496 9 Ft. (2.75 m) AIR FLOW 6"
ページ12に含まれる内容の要旨
' s"ola.su=t TYPICALDUCT ARRANGEMENTS Typical througft Rein" DUCt (Outside Waft) Through Cabinet Toe Space (|l_.side Wall) (See special instructions 204917) OPTIONAL DUCT ARRANGEMENT UNDER CONCRETE SLAB NOTE; PVC sewer pipe Wpe PSM 12454-S Also Required: Jenn-AW Kit P/N 712139, Ilvaileble trom your authorized set- t Sewer Pipe Coupling Sewer Pipe Elbow Sewer Pipe Elbow Pack tightly with gravel or =rand completely around pipe, I 12" Min, _ * Cut Off Pipe at ! Note: Window WeB installation Wall Cu
