ページ1に含まれる内容の要旨
27” Built In Wall Oven
Installation
JKP15, JKP18, JKP27, JKP45, JKP56 JKS05,
ZEK937, ZEK957
Instructions
“If you have questions, call 800-GE-CARES or visit our website at:
www.GEAppliances.com”
Before you begin
• ATTENTION INSTALLER!!
Read these instructions carefully and completely
All electric wall ovens must be hard wired
• IMPORTANT-Save these instructions for
(direct wired) into an approved junction
local inspector’s use.
box. A “plug and receptacle” is NOT permit-
• IMPORTANT-Observe all
ページ2に含まれる内容の要旨
Installation Instructions IMPORTANT SAFETY INSTRUCTIONS Electrical For Your Safety Requirements This appliance must be supplied with the • Be sure your oven is installed properly by proper voltage and frequency, and connected a qualified installer or service technician. to an individual properly grounded branch • Be sure the oven is securely installed in a circuit, protected by a circuit breaker or fuse cabinet that is firmly attached to the house having amperage as noted on rating plate. struct
ページ3に含まれる内容の要旨
EASY INSTALLATION OF YOUR NEW 30" WALL OVEN Before you begin-Read these instructions completely and carefully. Before you begin-Read these instructions completely and carefully. Before you begin-Read these instructions completely and carefully. Before you begin-Read these instructions completely and carefully. Before you begin-Read these instructions completely and carefully. Before you begin-Read these instructions completely and carefully. Before you begin-Read these instructions completely a
ページ4に含まれる内容の要旨
Installation Instructions Pre- Installation Checklist cont. Remove the bottom trim from the Place the oven on a table or platform top of the oven. It will be installed at even with the cutout opening. the end of installation. The trim is (Platform must support 150 lbs. wrapped separately and taped to the single, 275 lbs. double.) top of the unit. Bottom Trim Conduit Side Trim 4
ページ5に含まれる内容の要旨
Installation Instructions A1 Cutouts for Single Built-In-Oven Cabinet 10" Junction Box Cabinet Width 27 Width Location 27" Recommended Cutout Location from Floor 32 1/2” Cutout Width Allow 7/8" 25" MIN. Cutout Depth 23 1/2” for overlap of 25 1/4" MAX. oven over side 22" Min. edges of cutout above base Cutout rail Cutout Width 25” Min. 2" x 4" or Height equivalent 27 5/8" MIN. 25 1/4” Max. runners 28 1/8" MAX. Cutout Height 27 5/8” Min. 5" 20" 28 1/8” Max. Alternate junction box location NOTE:
ページ6に含まれる内容の要旨
Installation Instructions A2 Cutouts for Double Built-In-Oven Junction Box Location Cabinet 10" Width 27" Cutout Width 25" MIN. Cabinet Width 27” 25 1/4" MAX. Allow 7/8" Recommended for overlap of Cutout Location oven over side edges of cutout from Floor 13 1/4” 44" above base rail Alternate Cutout Cutout Depth 23 5/8” Min. junction Height box 49 11/16" MIN. 2" x 4" or location 50 1/8" MAX. equivalent runners Cutout Wdth 25” Min. 25 1/4” Max. 5" 20" Cutout Height 49 11/16” Min. 50 1/8” Max. Re
ページ7に含まれる内容の要旨
Installation Instructions Cutouts for Single Oven Under Counter A3 Gas or electric cooktops may be installed over this oven. See cooktop installation instructions for cutout size. See label on top of oven for Gas or electric connections approved cooktop models. for gas cooktop must be 240V / 208V located in an adjacent Junction Box accessible location Location to the right 25" 5" 25" MIN. 25 1/4" MAX. Allow 1" 32" 22" MIN. unit overlap Typical Above all edges 27 5/8" MIN. Counterto
ページ8に含まれる内容の要旨
Installation Instructions Electrical Connections B ATTENTION INSTALLER!!! Turn off the circuit breaker or remove fuses B1 All electric wall ovens must be hard wired to the oven branch circuit. (direct wired) into an approved junction With the oven in front of the cabinet box. A plug and receptacle is NOT B2 opening, on a table or platform, connect the permitted on these products. flexible conduit to the electrical junction box as shown below. You will need to purchase Do not shorten the flexible
ページ9に含まれる内容の要旨
Installation Instructions Electrial Connections cont. B NEW CONSTRUCTION AND OR FOUR-CONDUCTOR BRANCH CIRCUIT CONNECTION Three-Conductor Branch B4 Circuit Connection • When installing in a new construction, B3 or • When installing oven in a mobile When connecting to a 3-conductor branch home, or circuit, if local codes permit: • When local codes do not permit grounding through neutral: a.Connect the bare oven ground conductor with the crimped neutral (white) lead to the a. Cut the neutral (White
ページ10に含まれる内容の要旨
Installation Instructions Placing the Oven in the Opening C Sliding the Oven Into the Drilling the Pilot Holes C2 C1 Opening. a. Loop (do not tie) a 36” string around the Note: Before drilling the pilot holes conduit before the oven is slid into place. make sure the oven is pushed as far This will keep the conduit from falling behind back into the opening as it will go the oven. and centered. Pull out on string a. Drill four-1/8” pilot holes through the loop while mounting holes (top and bottom)
ページ11に含まれる内容の要旨
Installation Instructions Replacing the Oven Preparing for the bottom C3 D Door Trim Installation a. With oven installed, take the bottom trim The oven door is heavy. You may need and center it on the bottom front edge of help lifting the door high enough to the cabinet opening. slide it into the hinges slots. Do not lift b. Using the trim as the door by the handle. With Lower Trim With Lower Trim a template mark In Position In Position Mark (3) Mounting Mark (3) Mounting
ページ12に含まれる内容の要旨
Installation Instructions E PRE-TEST CHECK LIST Check that the bottom trim is installed Remove all protective film if present, properly (see page 10). and any stickers. Check to be sure that all wiring is Check to be sure the mounting screws secure and not pinched or in contact are installed and flush with the side with moving parts. trim, (see page 10). Operation Checklist NOTE TO ELECTRICIAN: Remove all items from the inside The power leads supplied with this of the oven. appliance are UL reco
