ページ1に含まれる内容の要旨
Installation Instructions
Discovery Wall Oven
For use with models: EO, MO and PO
Part No. 65433 Rev. F
Preliminary - For Review Only
No Scheduled Release Date
ページ2に含まれる内容の要旨
® All specifications are subject to change without notice. Dacor assumes no liability for changes to specifications. © 2007 Dacor, all rights reserved.
ページ3に含まれる内容の要旨
Table of Contents Before You Begin... ........................................................... 1 Planning the Installation ................................................... 6 Important Safety Instructions .......................................... 1 Selecting the Location ...................................................... 6 Important Information About Safety Instructions .............. 1 Cabinet Cut-Out ............................................................... 6 Safety Symbols and
ページ4に含まれる内容の要旨
Important Safety Instructions General Safety Precautions To reduce the risk of fire, electric shock, serious injury or death when using your appliance, follow basic safety precau- tions, including the following: WARNING WARNING 1. Read the accompanying use and care manual 15. To prevent injury due to the unit tipping forward, before operating this appliance. secure the oven to the cabinet using the supplied mounting screws. 2. Keep packaging materials away from children. Plastic sheets and b
ページ5に含まれる内容の要旨
Customer Service Information Model Identification If You Need Help... • If you have questions or problems with installation, con- EO230xxx tact your Dacor dealer or the Dacor Customer Service Team. When you call, have the model and serial num- A C ber of the appliance ready. The model and serial num- ber are printed on the appliance data plate. B D Dacor Customer Service t eam Phone: (800) 793-0093. A = MODEL tYPE E-mail: customerservice@Dacor.com Web site: www.Dacor.com Epicure O
ページ6に含まれる内容の要旨
Product Specifications Product Dimensions All tolerances are 1/16”, -0 (1.6 mm, -0) Model K L M N P Q R S Number EO127 PO127 27” 25 3/8” (686mm) (644mm) MOV127 MOH127 27 15/16” 26 3/8” (710mm) (670mm) EO130 PO130 30” 28 3/8” (762mm) (721mm) MOV130 MOV130 23 3/8” 2 5/16” 7 3/8” 6 3/8” (594mm) (59mm) (187mm) (162mm) EO227 PO227 27” 25 3/8” (686mm) (644mm) MOV227 MOH227 51 3/32” 49 1/2” (1298mm) (1257mm) EO230 PO230 30” 28 3/8” (762mm) (721mm) MOV230 MOH230 TM ® ® MILLENNIA EPICURE PREFERENCE 3 1
ページ7に含まれる内容の要旨
Product Specifications “S” “M” “N” “P” 1 1/4” (32mm) “Q” “L” “R” 1 1/16” (27mm) 66” (1676mm) Flexible Conduit “K” Single Wall Oven Dimension “S” “M” “N” 1 1/4” (32mm) “P” “Q” 1 1/16” (27mm) “L” “R” 66” (1676mm) Flexible Conduit “K” Double Wall Oven Dimension 5
ページ8に含まれる内容の要旨
Planning the Installation Model Selecting the Location A B C D Number • Carefully check the location where the oven is to be EO127 installed. The oven should be placed for convenient PO127 25 1/2” 27” 56 1/2” access, but away from drafts that may be caused (648mm) (686mm) (1435mm) MOV127 by doors, windows, and heating, ventilation and air conditioning outlets. MOH127 27 7/16” (697mm) • Make certain that electrical power can be provided EO130 in the selected location. Be certain that pr
ページ9に含まれる内容の要旨
Planning the Installation “D” NOtES: • All tolerances are 1/16”, -0 (1.6 mm, -0) • 24” minimum cutout depth • 3/4” support platform must be flush with front of cutout. See page 8. Recommended Electrical Location Recommended Electrical Location 1“ (25mm) Min. to Bottom of 4“ (102mm) Min. Door Between Cutout Duel Single Wall Oven Cutout “A” “A” “B” “B” 3/4” (19mm) 3/4” (19mm) Support Platform Support Platform Alternate 1 ¾“ (45mm) Electrical Min. to Top of Location Altern
ページ10に含まれる内容の要旨
Planning the Installation Cabinet Cut-Out (continued) Support Platform WARNING The top surface of the support platform must be installed flush with the cutout in the front of the cabinet or wall and any trim. Failure to install the platform properly may cause the exhaust vent to deform and/or become obstructed. An obstructed exhaust area may cause the oven to malfunction. See below. Provide a platform within the cabinet to support the oven. A properly supported piece of 3/4” (19mm) thick
ページ11に含まれる内容の要旨
Planning the Installation It is the owner’s responsibility to ensure that a qualified Electrical Specifications electrician performs the electrical connection of this appli- ance. The electrical installation, including minimum supply wire size, must comply with the National Electric Code IMPORt ANt ANSI/NFPA 70 (latest revision) and local codes and ordi- • Preheat times and cavity temperature recovery times nances. will be increased slightly if operating on less than a *A copy of this sta
ページ12に含まれる内容の要旨
Installation Instructions 1. Before proceeding, turn off power to the circuit to which Electrical Service Installation the oven will be connected at the circuit breaker or fuse box. WARNING 2. Position the oven directly in front of the cabinet cutout. • Wire the oven only in compliance with local ordi- 3. Feed the appliance conduit into the electrical junction nances. box and attach it using a UL approved strain relief. • If the electrical service provided does not meet 4. Depending upon
ページ13に含まれる内容の要旨
Installation Instructions Connecting to a Three Wire Electrical Connecting to a Three Wire Electrical System - Where Local Codes Permit System with External Ground - Where Local Codes Permit WARNING WARNING Do not connect the green appliance conduit wire to the neutral (white) junction box wire unless local building • Do not connect the green appliance wire to the junc- codes permit. tion box or to a cold water pipe unless local building codes permit. 1. Separate the wires coming out of
ページ14に含まれる内容の要旨
Installation Instructions Connecting to a Three Wire Electrical System with External Ground - Where Local Codes Permit (continued) Cable from Separate No. 10 (minimum) power supply copper grounding wire No. 4 Junction copper wire Meter box RED WHITE RED WHITE GREEN Clamp must be BLACK GREEN tight on pipe Metal BLACK Clamps water pipe Wire nut Bare metal (4 places) Conduit from appliance Final Installation WARNING • A minimum of two people are required to safely install th
ページ15に含まれる内容の要旨
Installation Instructions 3. Raise the door so that it is at a 15° angle from the front 2. Support the oven at all times until it is secured into the of the oven. Hold the door with one hand on each side. cabinet. Be certain to take all necessary safety precau- Lift the door up and out. tions. 3. Resting the oven on the cabinet support platform, slide the oven into the recessed area until the rear edge of the oven trim post is flush with the cabinet face and the oven is centered within the c
ページ16に含まれる内容の要旨
Installation Instructions 1. Grasp the oven door on opposite sides and hold it at a Install Exhaust Deflector 15° angle from the front of the oven. See facing page. CAUtION 2. Slide the hinges into the hinge openings, resting the bottom of the hinge arms on the hinge receptacles. Install the exhaust deflector before installing the oven 3. Continue to hold the door at a 15° angle with one hand door(s). while pushing in on each of the bottom corners of the Attach the exhaust deflector to th
ページ17に含まれる内容の要旨
Installation Instructions Lower lip of hinge receptacle Notch on bottom of hinge Door Installation Installation Checklist □ Plastic coating, if applicable, has been removed from WARNING outside of oven. • To ensure a safe and proper installation, the follow- □ All packaging materials have been removed from inside ing checklist should be completed by the installer the oven. to ensure that no part of the installation has been overlooked. □ Power is turned on at circuit breaker or fuse box
ページ18に含まれる内容の要旨
Notes 16
ページ19に含まれる内容の要旨
ページ20に含まれる内容の要旨
Dacor ● 1440 Bridge Gate Drive, Diamond Bar, CA 91765 ● Tel: (800) 793-0093 ● FAX: (626) 403-3130 ● www.Dacor.com
