ページ1に含まれる内容の要旨
IP200 MiniDome In-Ceiling Mount
NDA-FMT200-DOME
en Installation Manual
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
IP200 MiniDome In-Ceiling Mount Table of Contents | en 3 Table of Contents 1Safety 4 1.1 Safety precautions 4 2 Unpacking 5 2.1 Parts List 5 3 Installation Overview 6 4 Installing a Recessed Mount 7 4.1 Overview 7 4.2 Installing the Recessed Mount 7 4.3 Installing the Camera to the Recess Mount 11 5 Connection 14 Bosch Security Systems Installation Manual AM18-Q0626 | v1.0 | 2012.09
ページ4に含まれる内容の要旨
4 en | Safety IP200 MiniDome In-Ceiling Mount 1Safety Before installing and operating the camera, please read this manual carefully. 1.1 Safety precautions DANGER! High risk: This symbol indicates an imminently hazardous situation such as "Dangerous Voltage" inside the product. If not avoided, this will result in an electrical shock, serious bodily injury, or death. WARNING! Medium risk: Indicates a potentially hazardous situation. If not avoided, this could result in minor or moderate bodi
ページ5に含まれる内容の要旨
IP200 MiniDome In-Ceiling Mount Unpacking | en 5 2 Unpacking This equipment should be unpacked and handled with care. If an item appears to have been damaged in shipment, notify the shipper immediately. Verify that all the parts listed in the applicable Parts List below are included. If any items are missing, notify your Bosch Security Systems Sales or Customer Service Representative. The original packing carton is the safest container in which to transport the unit and must be used if ret
ページ6に含まれる内容の要旨
6 en | Installation Overview IP200 MiniDome In-Ceiling Mount 3 Installation Overview The IP200 MiniDome camera comes with the hardware and installation instructions necessary to mount the camera to a concrete ceiling. This following mounting accessory is available : – In-ceiling mount, used in applications where the camera is mounted into a recessed ceiling. The mount is supplied with two different trim rings and different tooling hole positions on the sides of the recess mount. Use the tab
ページ7に含まれる内容の要旨
IP200 MiniDome In-Ceiling Mount Installing a Recessed Mount | en 7 4 Installing a Recessed Mount 4.1 Overview This chapter details how to install a recessed mount for the IP200 MiniDome. NOTICE! The image sensors in modern cameras are highly sensitive and require special care for proper performance and extended lifetime. Follow the guidelines for optimum results with your camera: – Do not expose to direct sunlight or bright spotlights in operating and nonoperating conditions. – Avoid bri
ページ8に含まれる内容の要旨
8 en | Installing a Recessed Mount IP200 MiniDome In-Ceiling Mount 2. Drill or cut a 7 in. hole with a tolerance of +/- 1/8 in. (177.8 mm +/- 2.2 mm). 3. Optional: if installing the camera to a suspended ceiling tile or any other surface where additional support is required, the LTC 9349MK mounting kit (sold separately) is recommended. See the instruction book supplied with the mounting bracket for installation instructions. Figure 4.2 Mounting bracket 4. Align holes of mounting plate (supp
ページ9に含まれる内容の要旨
IP200 MiniDome In-Ceiling Mount Installing a Recessed Mount | en 9 Figure 4.3 Attach Recess Mount to Ceiling Figure 4.4 Attach Recess Mount to Ceiling 7. Tighten both clamps to the ceiling using supplied screws and a #2 Phillips screwdriver. Bosch Security Systems Installation Manual AM18-Q0626 | v1.0 | 2012.09
ページ10に含まれる内容の要旨
10 en | Installing a Recessed Mount IP200 MiniDome In-Ceiling Mount Figure 4.5 Tighten Mounting Clamps NOTICE! Over torquing the ceiling clamps can damage the clamp or ceiling. Only tighten the clamp until it contacts the ceiling and you start to feel some resistance. If using a power screwdriver, set the torque level to the lowest setting. AM18-Q0626 | v1.0 | 2012.09 Installation Manual Bosch Security Systems
ページ11に含まれる内容の要旨
IP200 MiniDome In-Ceiling Mount Installing a Recessed Mount | en 11 4.3 Installing the Camera to the Recess Mount To install the camera to the recess mount, follow these steps: CAUTION! All wires for installation applications must be routed through a grounded conduit. 1. Route wires on the side of mounting plate with the crescent shaped cut-out. 2. Connect the cables according to the instructions in the IP200 MiniDomes Installation Manual. Figure 4.6 Match Connectors Cable out 3. Attach the
ページ12に含まれる内容の要旨
12 en | Installing a Recessed Mount IP200 MiniDome In-Ceiling Mount to the mount using the M4 x 15 mm mounting screws. Ensure that the cable is aligned with the cutout in the recess mount. 4. Attach the camera base, and then install the upper housing/bubble. (See the camera User Manual for details.) Figure 4.7 Attach Camera to Recess Mount NOTICE! The recessed mounting bracket is provided with an additional safety tether point. To prevent injury, attach a safety wire from a secure anchor p
ページ13に含まれる内容の要旨
IP200 MiniDome In-Ceiling Mount Installing a Recessed Mount | en 13 Figure 4.8 Align Trim Ring 6. Fit the plastic trim ring. Use the supplied T-10 Torx wrench to secure the trim ring’s two safety locking screws to the mounting bracket. Bosch Security Systems Installation Manual AM18-Q0626 | v1.0 | 2012.09
ページ14に含まれる内容の要旨
14 en | Connection IP200 MiniDome In-Ceiling Mount 5 Connection After the camera is mounted, connect the network cable and the power cable. CAUTION! Do not connect power to the camera until all other connections are made. CAUTION! Installation should only be performed by qualified service personnel in accordance with the National Electrical Code or applicable local codes. CAUTION! All wires for installation applications must be routed through a grounded conduit. CAUTION! To prevent humi
ページ15に含まれる内容の要旨
ページ16に含まれる内容の要旨
Bosch Security Systems www.boschsecurity.com © Bosch Security Systems, 2012
