ページ1に含まれる内容の要旨
TEW-410APB
Wireless 802.11g AP
User’s Manual
Version 1.4
0
User’s Guide
ページ2に含まれる内容の要旨
Copyright Statement No part of this publication may be reproduced, stored in a retrieval system
ページ3に含まれる内容の要旨
Contents 1. Introduction.............................................................................................................. 3 2. Safety Notification ................................................................................................... 4 3. Hardware Installation .............................................................................................. 5 4 Web Management Settings ................................................................................
ページ4に含まれる内容の要旨
1. Introduction Thank you for purchasing your AP Wireless 802.11g AP. This user guide will as
ページ5に含まれる内容の要旨
2. Safety Notification Your Wireless AP should be placed in a safe and secure location. To ensure proper operation, please keep the unit away from water and other damaging elements. Please read the user manual thoroughly before you install the device. The device should only be repaired by authorized and qualified personnel. Please do not try to open or repair the device yourself. Do not place the device in a damp or humid location, i.e. a bathroom. The devic
ページ6に含まれる内容の要旨
3. Hardware Installation Front Panel The front panel provides LED’s for device status. Refer to
ページ7に含まれる内容の要旨
4 Web Management Settings TURN ON POWER SUPPLY Quick power cycle can caused system corruption. When power on, be careful not to shut down in about 5 seconds, because data is writing to the flash. START UP & LOGIN In order to configure the Wireless 11g AP, you must use your web browser and manually input http://192.168.1.250 into the Address box and press Enter. The Main Page will appear. To start configure the Wireless 11g AP, you must login as “admin” in the User
ページ8に含まれる内容の要旨
4.1. Primary Setup MAKE CORRECT NETWORK SETTINGS OF YOUR COMPUTER To change the configuratio
ページ9に含まれる内容の要旨
Wireless: This section provide the Wireless Network settings for your WLAN Wireless Settings SSID: The service set identifier ( SSID ) or network name. It is case sensitive and must not exceed 32 characters, which may be any keyboard character. You shall have selected the same SSID for all the APs that will be communicating with mobile wireless stations. Channel: Select the appropriate channel from the list provided to correspond with your network settings. You shall assign a
ページ10に含まれる内容の要旨
I m p o r t a n t N o t i c e In order to make right use of WPA, please ensure that your current Wireless Ada
ページ11に含まれる内容の要旨
-WPA RADIUS WPA RADIUS uses an external RADIUS server to perform user authentication. To use WPA RADIUS, enter the IP address of the RADIUS server, the RADIUS Port (default is 1812) and the shared secret from the RADIUS server. WPA Please choose your algorithms method. You can select Algorithms between TKIP or AES. Radius Please input your RADIUS Server IP address. Server Address RADIUS Please input the Authentication port of your RADIUS server. Server Port The default po
ページ12に含まれる内容の要旨
4.2. System AP Password: Changing the password for the AP is as easy as typing the password i
ページ13に含まれる内容の要旨
4.3. Operating Mode Access Point: This mode provides access for wireless stations to wired LANs and from wired LANs to wireless stations. 12 User’s Guide
ページ14に含まれる内容の要旨
AP Repeater: This mode allows the AP to keep the AP function role and at the same time performing
ページ15に含まれる内容の要旨
4.4. Status This screen displays the IEEE 802.11g AP' s current status and settings. This information is read-only. This page will auto re-flash every 5 seconds to keep most update information. LAN section will be displaying all information related on AP, such as the IP address and the current configuration type. Wireless section will be displaying information related on the Wireless interface, such as SSID, Channel, Encryption and statistics of network traffic. *Click t
ページ16に含まれる内容の要旨
4.5 Traffic Log Traffic Log: The AP can keep logs of all incoming or outgoing traffic for you
ページ17に含まれる内容の要旨
4.6 Access Control Access Control: This function will allow administrator to have access control by enter MAC address of client stations. When Enable this function, two new options will show up. Depend on the filtering propose, it can be selected to Deny or Allow. Fill the client stations MAC list to complete the configuration. The table could store up to 40 different MAC addresses. Please follow the format that it required when an address is input. * Click Apply to save yo
ページ18に含まれる内容の要旨
4.7 Advanced Wireless Authentication Type: Auto: Auto is the default authentication algorith
ページ19に含まれる内容の要旨
RTS Threshold: This value should remain at its default setting of 2346. Should you encounter inconsistent data flow, only minor modifications are recommended. If a network packet is smaller than the preset RTS threshold size, the RTS/CTS mechanism will not be enabled. The AP sends Request to Send (RTS) frames to a particular receiving station and negotiates the sending of a data frame. After receiving an RTS, the wireless station responds with a Clear to Send (CTS) frame to acknowledge
ページ20に含まれる内容の要旨
4.8. SNMP INFO SNMP INFO: The SNMP screen allows you to customize the Simple Network Management
