ページ1に含まれる内容の要旨
ページ2に含まれる内容の要旨
TM ADSL Barricade 4-Port ADSL Router with Built-in Annex A ADSL Modem User Guide February 2004
ページ3に含まれる内容の要旨
TABLE OF CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Using this Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Notational conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Typographical conventions . . . . . . . . . . . . . .
ページ4に含まれる内容の要旨
Table of Contents Getting Started with the Configuration Manager 23 Accessing the Configuration Manager . . . . . . . . . . . . . . . . . . . 23 Functional Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Commonly used buttons . . . . . . . . . . . . . . . . . . . . . . . . 25 The Home Page and System View Table . . . . . . . . . . . . . . . . 26 Modifying Basic System Information . . . . . . . . . . . . . . . . . . . . 28 Committing Changes and Rebooting . . . .
ページ5に含まれる内容の要旨
Table of Contents Viewing NAT Global Settings and Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Viewing NAT Rules and Rule Statistics . . . . . . . . . . . . . . . . . . 62 Viewing Current NAT Translations . . . . . . . . . . . . . . . . . . . . . . 63 Adding NAT Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 The NAPT rule: Translating between private and public IP addresses . . . . . . . . . . . . . . . . . . . . . . . . .
ページ6に含まれる内容の要旨
Table of Contents Viewing Your ATM VC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 Adding ATM VCs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 Modifying ATM VCs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102 Configuring PPP Interfaces . . . . . . . . . . . . . . . .105 Viewing Your Current PPP Configuration . . . . . . . . . . . . . . . 106 Viewing PPP Interface Details . . . . . . . . . . . . . . . . . . . . . . . . 109 Addin
ページ7に含まれる内容の要旨
Table of Contents Blocked Protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149 Viewing DSL Line Information . . . . . . . . . . . . . . 153 Administrative Tasks . . . . . . . . . . . . . . . . . . . . . 157 Configuring User Names and Passwords . . . . . . . . . . . . . . . . 157 Changing Login Passwords . . . . . . . . . . . . . . . . . . . . . 157 Viewing System Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159 Viewing the Alarm Table . . . . .
ページ8に含まれる内容の要旨
INTRODUCTION Congratulations on becoming the owner of the ADSL Barricade, a 4-port ADSL Router with built-in ADSL Modem. Your LAN (Local Area Network) will now be able to access the Internet using your high-speed ADSL connection. This User Guide will show you how to set up the ADSL Barricade, and how to customize its configuration to get the most out of your new product. Features External ADSL modem for high-speed Internet access. 10/100Base-T Ethernet router to provide Internet connect
ページ9に含まれる内容の要旨
Introduction System Requirements In order to use the ADSL Barricade, you must have the following: ADSL service up and running on your telephone line, with at least one public Internet address for your LAN. One or more computers each containing an Ethernet 10/100 Base-T network interface card (NIC). An Ethernet hub/switch, if you are connecting the device to more than one computer on an Ethernet network. For system configuration using the supplied web-based program: a web browser such
ページ10に含まれる内容の要旨
Using this Document Typographical conventions Italics are used to identify terms that are defined in the Terminology. Square brackets are used for items you select from menus and drop-down lists. Special messages This document uses the following statement to call your attention to specific instructions or explanations. Note: Provides clarifying or non-essential information on the current topic. Definition: Explains terms or acronyms that may be unfamiliar to many readers. These terms ar
ページ11に含まれる内容の要旨
GETTING TO KNOW THE ADSL BARRICADE Package Contents One ADSL Barricade. One Power adapter. One RJ-45 Ethernet cable. One RJ-11 Standard phone/DSL line cable. Installation utility and Documentation CD. Quick Installation Guide. 5
ページ12に含まれる内容の要旨
Getting to Know the ADSL Barricade Hardware Description Front Panel LED Label Power Link TX/RX Ethernet 1 2 3 4 Color Status Green Green Green Green / 100 Mbps Yellow / 10 Mbps Green Steady Power On ADSL line DSL Link is trained. Transmitting/ Receiving Green Blink N/A Training TX/RX Transmitting/ Receiving Yellow Steady N/A N/A N/A Link Yellow Blink N/A N/A N/A Transmitting/ Receiving OFF Power Off No Connection No TX/RX No Connection (*Alarm LED is optional, and for manufactory only*) T
ページ13に含まれる内容の要旨
QUICK START This Quick Start provides basic instructions for connecting the ADSL Barricade to a computer or LAN and to the Internet. Connecting the Hardware describes how to set up the hardware. Configuring Your Computers describes how to configure Internet properties on your computer(s). Configuring the ADSL Barricade shows you how to configure basic settings on the ADSL Barricade to get your LAN connected to the Internet. This Quick Start assumes that you have already established
ページ14に含まれる内容の要旨
Quick Start Wall Jack ADSL Barricade AC adapter To a hub: use cross- over cable to uplink or port or straight cable to standard port To a PC: use a cross-over cable Hub/switch (for local area network) Stand-alone computer Networked Computers Figure 1. Overview of Hardware Connections Step 1. Connect the ADSL cable Connect one end of the provided phone cable (RJ-11) to the port labeled ADSL on the Rear Panel of the device. Connect the other end to your wall phone jack. You can attach a te
ページ15に含まれる内容の要旨
Configuring Your Computers Step 2. Connect the Ethernet cable If you are connecting a LAN to the ADSL Barricade, attach one end of a provided Ethernet cable to a regular hub port and the other to the Ethernet port on the ADSL Barricade. If you are using the ADSL Barricade with a single computer and no hub, you must use an Ethernet cable to attach the PC directly to the device. The cable is wired differently than the cable you would use to connect to a hub. Step 3. Attach the power connecto
ページ16に含まれる内容の要旨
Quick Start If you have connected your PC of LAN via Ethernet to the ADSL Barricade, follow the instructions that correspond to the operating system installed on your PC. ® Windows XP 1. In the Windows task bar, click the [Start] button, and then click [Control Panel]. 2. Double-click the [Network Connections] icon. 3. In the [LAN or High-Speed Internet] window, right-click on the icon corresponding to your network interface card (NIC) and select [Properties]. (Often, this icon is labeled [
ページ17に含まれる内容の要旨
Configuring Your Computers Windows 2000 First, check for the IP protocol and, if necessary, install it. 1. In the Windows task bar, click the [Start] button, point to [Settings], and then click [Control Panel]. 2. Double-click the [Network and Dial-up Connections] icon. 3. In the [Network and Dial-up Connections] window, right-click the [Local Area Connection] icon, and then select [Properties]. The [Local Area Connection Properties] dialog box displays a list of currently installed network
ページ18に含まれる内容の要旨
Quick Start 10. In the [Local Area Connection Properties] dialog box, select [Internet Protocol (TCP/IP)], and then click [Properties]. 11. In the [Internet Protocol (TCP/IP) Properties] dialog box, click the radio button labeled [Obtain an IP address automatically]. Also click the radio button labeled [Obtain DNS server address automatically]. 12. Click [OK] twice to confirm and save your changes, and then close the Control Panel. Windows Me 1. In the Windows task bar, click the [Start] bu
ページ19に含まれる内容の要旨
Configuring Your Computers 8. If prompted, click [OK] to restart your computer with the new settings. Next, configure the PCs to accept IP information assigned by the ADSL Barricade. 9. In the Control Panel, double-click the [Network and Dial-up Connections] icon. 10. In the [Network and Dial-up Connections] window, right-click the [Network] icon, and then select [Properties]. 11. In the [Network Properties] dialog box, select [TCP/IP], and then click [Properties]. 12. In the [TCP/IP Settin
ページ20に含まれる内容の要旨
Quick Start 4. Select [Protocol], and then click [Add...]. The [Select Network Protocol] dialog box appears. 5. Click on [Microsoft] in the [Manufacturers] list box, and then click [TCP/IP] in the [Network Protocols] list box. 6. Click [OK] to return to the [Network] dialog box, and then click [OK] again. You may be prompted to install files from your Windows 95/98 installation CD. Follow the instructions to install the files. 7. Click [OK] to restart the PC and complete the TCP/IP installa
