ページ1に含まれる内容の要旨
INTELLISTRIPE 380
USB/RS-232
DESKTOP MOTORIZED READER-ENCODER
TECHNICAL REFERENCE MANUAL
Manual Part Number 99875275-3
AUGUST 2007
REGISTERED TO ISO 9001:2000
1710 Apollo Court
Seal Beach, CA 90740
Phone: (562) 546-6400
FAX: (562) 546-6301
Technical Support: (651) 415-6800
www.magtek.com
ページ2に含まれる内容の要旨
© Copyright 2001-2007 ® MagTek , Inc. Printed in the United States of America Information in this document is subject to change without notice. No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the express written permission of MagTek, Inc. MagTek is a registered trademark of MagTek, Inc. IntelliStripe is a registered trademark of MagTek, Inc. © USB (Universal Serial Bus) Specification is Co
ページ3に含まれる内容の要旨
REGISTERED TO ISO 9001:2000 MagTek Part Number 99875275-1 1710 Apollo Court, Seal Beach, CA 90740 25 February 2003 Voice: 562-546-6400 Fax: 562-546-6301 SOFTWARE LICENSE AGREEMENT IMPORTANT: YOU SHOULD CAREFULLY READ ALL THE TERMS, CONDITIONS AND RESTRICTIONS OF THIS LICENSE AGREEMENT BEFORE INSTALLING THE SOFTWARE PACKAGE. YOUR INSTALLATION OF THE SOFTWARE PACKAGE PRESUMES YOUR ACCEPTANCE OF THE TERMS, CONDITIONS, AND RESTRICTIONS CONTAINED IN THIS AGREEMENT. IF YOU DO NOT AG
ページ4に含まれる内容の要旨
FCC WARNING STATEMENT This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio co
ページ5に含まれる内容の要旨
TABLE OF CONTENTS SECTION 1. FEATURES AND SPECIFICATIONS..................................................................................... 1 CONFIGURATIONS ................................................................................................................................. 1 FEATURES............................................................................................................................................... 1 APPLICABLE DOCUMENTS .........................
ページ6に含まれる内容の要旨
Flange................................................................................................................................................. 11 MagTek Mounting Plate...................................................................................................................... 11 REAR PANEL AND CABLE CONNECTIONS........................................................................................ 12 SECTION 3. OPERATION AND MAINTENANCE ...................................
ページ7に含まれる内容の要旨
TABLE OF FIGURES Figure 1-1. IntelliStripe 380---------------------------------------------------------------------------------------------------viii Table 1.1. Specifications------------------------------------------------------------------------------------------------------10 Figure 2-1. Dimensions for Mounting Holes for 3-Screw Set and Foot Pads ------------------------------------12 Figure 2-2. Dimensions for Mounting Holes for Lock-in-Place Slots -------------------------------
ページ8に含まれる内容の要旨
Figure 1-1. IntelliStripe 380 viii
ページ9に含まれる内容の要旨
SECTION 1. FEATURES AND SPECIFICATIONS ® The IntelliStripe 380, Desktop Motorized Reader-Encoder reads and encodes magnetic-stripe cards and smartcards. CONFIGURATIONS Part numbers and descriptions for the basic configuration are as follows: 16050408 IntelliStripe 380 16050410 IntelliStripe 380, Magstripe Only 16051417 I/O Cable, 10-pin RJ45 connector connects to host 9-pin connector with 12V/Ground connector for Power Supply. 16051422 USB Cable, 5-pin mini B plug, co
ページ10に含まれる内容の要旨
IntelliStripe 380 APPLICABLE DOCUMENTS Standards ISO 7811-2, -3, -4, -5 Identification cards tracks 1-3 ISO 7810 Physical specifications ISO 7816 Smartcard specifications EMV 1996 Europay-Mastercard-Visa 1996 Level I Specification EMV 2000 Europay-Mastercard-Visa 2000 Level I Specification MagTek Documents MCP Serial Transport Protocol, P/N 99875163 IntelliStripe 380, Command Reference Manual, P/N 99875217 SOFTWARE ACCESSORIES The following Software Module
ページ11に含まれる内容の要旨
Section 1. Features and Specifications Motorized Card Transport The Card Transport is based on an existing MagTek magstripe/encode module. This module incorporates the following features: Lead-in Roller System The primary purpose of the Lead-in Roller System is to grab the card from the user during card insertion and to make sure the card is mechanically under motor control before reaching the read/write head and its associated drive rollers. As a secondary function, the L
ページ12に含まれる内容の要旨
IntelliStripe 380 Spring-Loaded Card Registration Guide(s) The spring-loaded guide ensures that the reference edge of the card is mechanically referenced to the magnetic read/write head, so that the magnetically encoded track data is physically located on the magstripe in accordance with the specifications of ISO 7811. Ability To Transport 0.010 ”to 0.035” Cards Cards that meet the ISO 7810 card thickness of 0.027” to 0.033 will work properly with both magnetic and smartcard el
ページ13に含まれる内容の要旨
Section 1. Features and Specifications Direction of Magnetic Read: The ISO 7810 and 7811 specifications allow for bidirectional magnetic reading of the card. As such, the Reader provides services that allow the card to be read in either direction. Read Formats: In addition to reading cards that meet the ISO 7810 and 7811 specifications, the Reader reads AAMVA drivers license cards. Also, all 3 tracks of the Reader reads any card that follows ISO 5-bit or 7-bit data formats and
ページ14に含まれる内容の要旨
IntelliStripe 380 Cable Management The following provisions are made for communication and power lines: • Polarization and locking of cable connectors • Strain relief of cables • Wire routing functionality • RJ series connectors for main and auxiliary RS-232 interfaces. • Power is brought to the unit through the main RS-232 cable • Power-pack is away from the unit and will attach to the main RS-232 cable Jam Clearance – Ejector Rod For easy removal of a jammed card, an e
ページ15に含まれる内容の要旨
Section 1. Features and Specifications RAM Space: 40 K bytes ROM Space: ROM Flash: Main Program Memory: 512 K Bytes Boot Loader Memory: 24 K Bytes Configuration Memory: 8 K Bytes Host Serial Port The RS-232 Host Serial Port provides serial communications between the Reader/Encoder and the Host Computer. In addition, the Host Serial Port carries DC power from the remote power pack to the Reader/Encoder. The Host Serial Port is capable of communication speeds of
ページ16に含まれる内容の要旨
IntelliStripe 380 Opto-Sensor Inputs The Main PCB provides inputs for the three opto-sensors (Front, Encode, and Rear). Rotary Pulse Generator The Main PCB provides input for the MagTek 75/210 bpi Rotary Pulse Generator (RPG). External SAM Ranch Interface, Optional The Main PCB provides resources for interconnect, securement, and power of an optional SAM Ranch PCB. The optional SAM Ranch PCB is accessed from the hatch door at the bottom of the Encoder/Reader. Dual Colo
ページ17に含まれる内容の要旨
Section 1. Features and Specifications External Auto-Ranging Power Pack The Reader/Encoder is powered from an external power-pack, which is located near the Host Computer System. Power is routed to the Reader/Encoder through the Host RS-232 cable. Auto-Ranging Input The external power pack features an Auto-ranging AC input that allows for direct connection to either a 100 VAC or 220 VAC, 50 to 60 Hz. Output Rating The power pack is rated at approximately +12 VDC @ 4 A
ページ18に含まれる内容の要旨
IntelliStripe 380 SPECIFICATIONS The Specifications are listed in Table 1-1. Table 1.1. Specifications OPERATING MSR Read-data Format Mag-Stripe: ANSI/ISO 7810, 7811/AAMVA/ for tracks 1, 2, and 3 Specifications Supported Smart Card: ISO 7816-1, -2, and -3 Encode Coercivity LoCo = 325 Oe +/- 75 Oe ( Range of 250 Oe to 400 Oe ) Ranges HiCo = 2750 Oe +/- 500 Oe ( Range of 2250 Oe to 3250 Oe ) Input Voltage +12 VDC ±5% Current Draw Idle: 300 mA Max: 3.0 A (during HiCo
ページ19に含まれる内容の要旨
SECTION 2. INSTALLATION The installation of the IntelliStripe 380 Reader-Encoder consists of mounting the unit on a flat surface, connecting the I/O RS-232 cable to the host serial port, the Auxiliary cable to a peripheral device, and the Power Supply to the I/O cable and to a wall receptacle. MOUNTING The bottom of the unit is shown in Figure 2-1 and 2-2. The IntelliStripe 380 may be mounted in one of three ways: 1) foot pads, 2) set of mounting holes for 3 screws (4 x 40), and
ページ20に含まれる内容の要旨
IntelliStripe 380 1.105 5.789 .546 Mounting Screws #4-40 (3) Foot Pads (4) Figure 2-1. Dimensions for Mounting Holes for 3-Screw Set and Foot Pads 2.810 4.330 .959 .375 (4) Ø .125 Mounting Flange (1) (use with Lock-In-Place mounting holes) .180 (4) Lock-In-Place Slots (4) Figure 2-2. Dimensions for Mounting Holes for Lock-in-Place Slots REAR PANEL AND CABLE CONNECTIONS To access the rear panel and cable connections on the IntelliStripe 380, remove the rear panel cover
