ページ1に含まれる内容の要旨
ZXDSL 831/831B/831 /831B
User’s Manual
Document version: 20051202-R2.1
Copyright 2006 ZTE Corporation
All rights reserved.
No part of this documentation may be excerpted, reproduced,
translated, annotated or duplicated, in any form or by any
means without the prior written permission of ZTE
Corporation.
ZTE CORPORATION reserves the right to modify this manual
for product upgrade or other causes without notifying users in
advance.
ページ2に含まれる内容の要旨
Limited warranty ZTE warrants that, for one year from the date of delivery by ZTE to purchaser's designated carrier, the Equipment will remain free from defects in design, material and workmanship under normal use and service and will conform in all material respects to the applicable specifications set forth in purchase order or agreement; ZTE does not warrant that operation of the Equipment will be error-free or uninterrupted. In accordance with ZTE's standard, warranty terms, ZTE
ページ3に含まれる内容の要旨
ZXDSL 831/831B/831II/831BII User’s Manual procedures; provided that if End User causes or permits services to be provided by individuals who are not ZTE-certified, the Warranty shall be void as to all Equipment serviced in breach of this sentence. End User shall have no right to reject, return, or receive a refund for any Equipment from ZTE. Any item repaired or replaced by ZTE shall continue to be warranted for the longer of the remainder of the original warranty period
ページ4に含まれる内容の要旨
ZXDSL 831/831B/831II/831BII User’s Manual TO, LOST PROFITS, COST OF CAPITAL, COST OF SUBSTITUTE FACILITIES OR EQUIPMENT, ANY DOWNTIME COSTS OR CLAIMS OF END USERS. THE LIABILITY OF EACH PARTY UNDER THIS AGREEMENT, WHETHER ARISING OUT OF BREACH OF CONTRACT (INCLUDING BUT NOT LIMITED TO BREACH OF WARRANTY) OR TORT (INCLUDING BUT NOT LIMITED TO NEGLIGENCE AND STRICT LIABILITY) OR UNDER AN INDEMNIFICATION PROVISION SHALL IN NO EVENT EXCEED THE AGGREGATE AMOUNT BENIFITE
ページ5に含まれる内容の要旨
Contents Chapter 1 Safety Guidance............................................................1 1.1 Safety Check.....................................................................................1 1.2 Safety Cautions.................................................................................1 Chapter 2 Overview .......................................................................3 2.1 Features........................................................................................
ページ6に含まれる内容の要旨
Chapter 1 Safety Guidance 1.1 Safety Check Before installing the ZXDSL 831/831B/831II/831BII ADSL equipment, you must check the following items. 1 Electric safety l Ensure that there are no inflammable, conductive or moist objects around. Check whether the cables are aged and whether other electrical appliances are placed stably. 2 Equipment position l Because the running electric devices easily generate heat, please ensure that these devices are positioned in a well ventilated
ページ7に含まれる内容の要旨
ページ8に含まれる内容の要旨
Chapter 2 Overview The ZXDSL 831/831B/831II/831BII is an ADSL access device that allows multiple line transmission modes. The equipment provides a 10/100Base-T Ethernet interface in a local LAN device. Through the high-speed ADSL access service, the ZXDSL 831/831B/831II/831BII can provide the broadband Internet service or enterprise network access service for users. 2.1 Features The ZXDSL 831/831II, as an routing-capable ADSL MODEM, is of the following characteristics: l Providing A
ページ9に含まれる内容の要旨
ZXDSL 831/831B/831II/831BII User’s Manual l Supporting multiple line modes (self-adaptive lines). l Providing a 10/100Base-T Ethernet interface. l More highly reliable, simpler operation and less power consumption. l Instant plug and instant use, with no configuration required l Supporting 64 PVCs l Supporting the Bridge mode 2.2 Product Specifications l Environmental requirements Environmental temperature: 0°C-40°C (32 °F-104°F) Humidity: 20% - 90% (non-condens
ページ10に含まれる内容の要旨
ページ11に含まれる内容の要旨
ZXDSL 831/831B/831II/831BII User’s Manual 3 Operating system Operating systems can be Windows 98SE, Windows Me, Windows 2000 or Windows XP. For system configuration in the WEB interface, the browser of Internet Explorer V 6.0 or later. 6
ページ12に含まれる内容の要旨
Chapter 3 Installation Preparation 3.1 Hardware Description Front panel Power DSL Internet Ethernet Figure 3.1-1 Front Panel of the ZXDSL 831/831B/831II/831BII Table 3.1-1 Descriptions of the LEDs on the Front Panel LED No. Color Status Note Off Shutdown Power Green/Red Software upgrade. Red Flash Green On Power on No signals are detected Off DSL Green Flash The MODEM is trying to be in the activation status On The MODEM has been activated. The system is under the Bridge
ページ13に含まれる内容の要旨
ZXDSL 831/831B/831II/831BII User’s Manual Rear panel Figure 3.1-2 Rear Panel of the ZXDSL 831/831B/831II/831BII Table 3.1-2 Description of Interfaces on the Rear Panel Item Introduction RJ-11 connection interface: The equipment is connected to the ADSL line or DSL splitter via the telephone line. In the power-on state, you can restore the system to the default configuration by using a thin needle to press this slot for three seconds or for three Reset executive
ページ14に含まれる内容の要旨
ZXDSL 831/831B/831II/831BII User’s Manual DSL Reset Ethernet PWR RJ-11 RJ-45 ADSL service Splitter MODEM socket LINE Power PHONE adapter Power PC TelephoneTelephone socket Figure 3.2-1 ZXDSL 831/831B/831II/831BII Connection Schematic Diagram (No Phone sets are Installed Before the Splitter) Connection 2 Figure 3.2-2 shows the connection when the splitter is installed near the ZXDSL 831/831B/831II/831BII. DSL Reset Ethernet PWR ADSL Splitter service RJ-11 RJ
ページ15に含まれる内容の要旨
ページ16に含まれる内容の要旨
ZXDSL 831/831B/831II/831BII User’s Manual using the RJ-11 telephone cable, connect the phone set lines to the PHONE interface of the splitter, and then connect the user telephone cable port to the LINE interface of the splitter. 4 Connect the power Connect one terminal of the power adapter to the PWR interface of the ZXDSL 831/831B/831II/831BII, and the other terminal to the socket on the wall, and then switch on the power of the ZXDSL 831/831B/831II/831BII equipment.
ページ17に含まれる内容の要旨
Appendix A FAQs All indicators are off after the ZXDSL 831/831B/831II/831BII equipment is 1 powered on First make sure that you have inserted the power adapter of the ZXDSL 831/831B/831II/831BII into a working power socket and that the ZXDSL 831/831B/831II/831BII has been powered on (the switch button is pressed down). If the indicators are still off after confirmation of the above items, the hardware is damaged probably. You may contact local operators for maintenance. Never dism
ページ18に含まれる内容の要旨
ZXDSL 831/831B/831II/831BII User’s Manual 5 Password verification failure MODEM synchronization and connection are normal. However, sometimes the password fails to be verified. 1. Note that the account and password are case sensitive and some accounts contain a domain name. 2. Virtual dialup software. It is possible that sometimes the virtual dialup software is faulty, or conflict with other software in the operating system. At this time, you are suggested to rei
ページ19に含まれる内容の要旨
ZXDSL 831/831B/831II/831BII User’s Manual 7 The authenticated user names and passwords cannot be re-authenticated? This problem may be due to the following reasons: 1. Your account has expired or you are a defaulting subscriber (please pay the deficit sum). 2. You move into a new area. Because the account and the path PVC are bundled by some operators, your previous account and password cannot be authenticated after you changed your path. 3. One of your accounts
ページ20に含まれる内容の要旨
Appendix B Standard Compliance 1 The equipment complies with the following ADSL standards: Standard Note ANSI T1.413 Issue 2 ITU G.992.1 Annex A ITU G.992.2 Annex A ITU G.992.3 Annex A Only supported by the ZXDSL 831II/831BII ITU G.992.3 Annex L Only supported by the ZXDSL 831II/831BII ITU G.992.5 Annex A Only supported by the ZXDSL 831II/831BII ITU G.994.1 2 ZTE’s equipment complies with the following national standards of the PRC: Standard No. Standard Name Safety of
