Z-Com R2 Extenderの取扱説明書

デバイスZ-Com R2 Extenderの取扱説明書

デバイス: Z-Com R2 Extender
カテゴリ: ネットワークルーター
メーカー: Z-Com
サイズ: 0.96 MB
追加した日付: 5/26/2013
ページ数: 20
説明書を印刷

ダウンロード

使い方は?

私たちの目的は、皆様方にデバイスZ-Com R2 Extenderの取扱説明書に含まれたコンテンツを可能な限り早く提供することです。オンラインプレビューを使用すると、Z-Com R2 Extenderに関してあなたが抱えている問題に対する解決策の内容が素早く表示されます。

便宜上

説明書Z-Com R2 Extenderをこちらのサイトで閲覧するのに不都合がある場合は、2つの解決策があります:

  • フルスクリーン表示 – 説明書を(お使いのコンピュータにダウンロードすることなく)便利に表示させるには、フルスクリーン表示モードをご使用ください。説明書Z-Com R2 Extenderのフルスクリーン表示を起動するには、全画面表示ボタンを押してください。
  • コンピュータにダウンロード - Z-Com R2 Extenderの説明書をお使いのコンピュータにダウンロードし、ご自身のコレクションに加えることもできます。デバイス上のスペースを無駄にしたくない場合は、いつでもManualsBaseサイトでダウンロードすることもできます。
Z-Com R2 Extender 取扱説明書 - Online PDF
Advertisement
« Page 1 of 20 »
Advertisement
印刷版

多くの人々は画面表示ではなく印刷された説明書を読むほうを好みます。説明書を印刷するオプションも提供されており、上記のリンクをクリックすることによりそれを利用できます - 説明書を印刷。説明書Z-Com R2 Extenderを全部印刷する必要はなく、選択したページだけを印刷できます。紙を節約しましょう。

要旨

次のページにある説明書Z-Com R2 Extenderの内容のプレビューは、以下にあります。次のページにある説明書の内容をすぐに表示したい場合は、こちらをご利用ください。

内容要旨
ページ1に含まれる内容の要旨








R2 Extender

Quick Installation Guide




V 1.0 January 2009

Page 1

ページ2に含まれる内容の要旨

Copyright Copyright © 2008 all rights reserved. No part of this publication may be reproduced, adapted, stored in a retrieval system, translated into any language, or transmitted in any form or by any means without the written permission of the supplier. About the Installation Guide This Installation Guide is intended to guide professional installer to install the R2 Extender. It includes procedures to assist you in avoiding unforeseen problems. Conventions Warning: This indica

ページ3に含まれる内容の要旨

Chapter 1 Introduction Introduction The R2 Extender is a high-performance outdoor-deployable wireless bridge that provides wireless connectivity among multiple network locations. It supports Base Station, CPE, PTP and PTMP connectivity. Moreover, the R2 Extender has a built-in 23dBi planar antenna that can deliver up to a 40Km connection. An external antenna may also be used to improve signal quality, extend distance and flexible for local coverage applications. With high throughput

ページ4に含まれる内容の要旨

Chapter 2 Preparation before Installation This chapter describes safety precautions and product information you have to know and check before installing R2 Extender. Professional Installation Required 1. Please seek assistance from a professional installer who is well trained in the RF installation and knowledgeable in the local regulations. 2. The R2 Extender is distributed through distributor and system installer with professional technicians and will not be sold directly through re

ページ5に含まれる内容の要旨

Product Package The product package you have received should contain the following items. If any of them are not included or damaged, please contact your local vendor for support. R2 Extender with integrated 23dBi antenna ×1 Mounting Kit ×1 PoE Injector & Power cord ×1 Grounding Wire w/ screw ×1 Water Proof RJ-45 Connector Kit ×1 Quick Installation Guide ×1 Product CD…………………

ページ6に含まれる内容の要旨

10. Wood Screw ×4 (for Wall Mount) 11. Wall/Gyprock Plug ×4 (for Wall Mount) Waterproof RJ-45 Connector Kit 1. Gland ×1 2. Sealing Nut ×1 3. Sealing ×1 Page 6

ページ7に含まれる内容の要旨

Chapter 3 System Installation Assemble the Mounting Bracket 1. Place the main bracket into the seating and use a spanner to fasten the bracket to the R2 8 9 Extender with M5×16 screws ○ and M5 washers ○ provided in the hardware packets; 2 1 2. Assemble the main bracket by placing articulation pole ○ to the T-form bracket ○ via a 4 5 M8×90 ○ screw through the insertion axe and fix with the M8 washer ○ , spring washer 6 7 ○ and M8 nut ○; Pole Mounting 3 1. Install the main brac

ページ8に含まれる内容の要旨

4 5 2. Fasten two M8×80 screws ○ and washers ○ through the drill holes and main bracket with a spanner; 3. Adjust the antenna for appropriate tilt / vertical orientation. Chapter 3 Hardware Installation Page 8

ページ9に含まれる内容の要旨

Connect Up Before installing the Ethernet cable with a waterproof RJ-45 connector, it is recommended that the Cat-5 RJ-45 coaxial cable be used for the bridge to power injector connections. 1. To connect to the hole labeled PoE+Data, open the black cover in advance by using a coin or a slotted screwdriver and then screw in the body of the gland and tighten. 2. Slide the sealing nut to the RJ-45 cable from its middle breach and then insert the sealing into the cable. Slide t

ページ10に含まれる内容の要旨

Ground the Wire The R2 Extender is shipped with a grounding wire. The unit must be properly grounded to protect against power surges. The grounding point can be found on the bottom of the unit. It is supplied with an appropriate grounding lug for attachment to the ODU. Power On To power up the R2 Extender, follow the steps bellow: 1. Plug a user-supplied Cat-5 Ethernet cable from your wired LAN (or a computer) into the power injector RJ-45 jack (DATA IN); 2. Plug a user-supplied

ページ11に含まれる内容の要旨

Warning: Make sure PoE is correctly connected to the RJ-45 port on the R2 Extender labeled PoE+Data. DO NOT connect to the port labeled “Warning!! No POE”, otherwise the extender will be severely damaged! Chapter 5 Troubleshooting Page 11

ページ12に含まれる内容の要旨

Chapter 4 Configuration Connect the R2 Extender to a Local Computer If you are configuring the R2 Extender locally (without connecting its power injector to a wired LAN), connect a PC to the power injector’s Ethernet port using a Category 5 Ethernet cable. 1. Assign a static IP address to your PC which is in the same network segment with the R2 Extender. As the default IP address of this unit is 192.168.1.1, you may choose from 192.168.1.2 to 192.168.1.254. 2. Test the link status bet

ページ13に含まれる内容の要旨

R2 Extender’s still initializing System ready Note: Considering convenient configuration, it is recommended to configure local and remote R2 Extender respectively on two computers. TTL time may vary depending on the operating system.. Chapter 5 Troubleshooting Page 13

ページ14に含まれる内容の要旨

How to Establish Wireless Bridge Mode The R2 Extender supports four operating modes, which are Base Station, CPE, Peer-to-Peer (CSMA) and Peer-to-Peer (TDMA). Normally, Wireless Bridge is the typical mode on this unit. Here we will illustrate how to establish wireless bridge connectivity with R2 Extender. Enter the user name (admin) and password (password) to login and make configurations. Note: Due to browser’s security trusted sites, 192.168.1.1 might not able to be opened. Yo

ページ15に含まれる内容の要旨

192.168.1.2 and set the IP Subnet Mask on both as 255.255.255.0 Warning: Each IP address is unique within a LAN, otherwise IP collision may occur! Open “Radio” in “Wireless” and you will find the default operating mode is Peer-to-Peer (CSMA). Select RF1(WLAN1) or RF2 (WLAN2) as Bridge to make the following configuration. Here we take RF1 as an example. Se select Peer-to-Peer (CSMA) operating mode and keep the Channel/Frequency and Bandwidth on both R2 Extenders identical. Click “

ページ16に含まれる内容の要旨

Login the Web-based interface of remote R2 Extender, open “About” in “System” and record the wireless MAC address of it, either WLAN 1 or WLAN 2 MAC Address. Login the Web-based interface of local R2 Extender and open “Peer-to-Peer Setup” in “Wireless”. Select “RF1” , input the WLAN1 or WLAN2 MAC address of the remote one to “Remote MAC Address 1” field and click “Apply”; Chapter 5 Troubleshooting Page 16

ページ17に含まれる内容の要旨

Warning: The MAC address on the housing of R2 Extender is the ETH MAC address; therefore it can not be used in Peer-to-Peer links. The IP address of your PC should be in the same network segment to the one of bridges. Use ping to check whether the link between the two R2 Extender is OK. R2 Extender A R2 Extender B To get a better wireless connectivity, antenna alignment is strongly recommended after both R2 Extenders are installed long distance apart. Login the Web-b

ページ18に含まれる内容の要旨

in “Wireless”. Select RF1 and hit “Align Antenna” button, an antenna alignment tool will popup. Specify the Target RSSI and click “Start” to begin the antenna alignment. Fix the local antenna and adjust the remote antenna elevation and horizontal direction. During the adjustment, observe “Current RSSI” in local R2 Extender. Fix the remote antenna when it reaches your expectation. Usually, RSSI between -60 and -70dBm indicates rather good signal strength. Adjust the local antenna af

ページ19に含まれる内容の要旨

Chapter 5 Troubleshooting This chapter provides troubleshooting procedures for basic problems with the R2 Extender. Q 1. What if my R2 Extender fails to connect to the remote one? • Ethernet Link: Check the availability of power to the bridge by observing the LED status on the power injector. - Green: The R2 Extender is connecting to the backhaul network. - Off: The R2 Extender disconnects from the wired network, check whether the power cord and Ethernet cables to the network and bridg

ページ20に含まれる内容の要旨

Chapter 6 Service Information If you have any further trouble using the R2 Extender or you would like to require additional support, you may visit our website at www.zcom.com.tw/rpc or you may contact us as below for support: Z-Com, Inc. Taiwan 7F-2, No.9. Prosperity Tel: +886-3-5777364 Sales Contact Business RD. I Science-Based Fax:+886-3-5773359 info@zcom.com.tw Center Industrial Park FAE Support Hsinchu ,300 Taiwan support@zcom.com.tw Zcomax Technologies, Inc. California


類似の説明書
# 取扱説明書 カテゴリ ダウンロード
1 Z-Com SRZ IMS01T05-E2 取扱説明書 ネットワークルーター 1
2 Z-Com R1 Extender 取扱説明書 ネットワークルーター 1
3 Z-Com ZMAX-8210-I 取扱説明書 ネットワークルーター 80
4 Z-Com ZMAX-8210-E 取扱説明書 ネットワークルーター 1
5 Sony BKS-R3202/R3210/R3220 取扱説明書 ネットワークルーター 77
6 Sony DVS-V3232B/V3232M 取扱説明書 ネットワークルーター 3
7 Sony BVS-V3232 取扱説明書 ネットワークルーター 8
8 Sony DMX-WL1 取扱説明書 ネットワークルーター 6
9 Sony BVS-A3232 取扱説明書 ネットワークルーター 6
10 Sony BKS-R1601 取扱説明書 ネットワークルーター 3
11 Sony CI-100 取扱説明書 ネットワークルーター 0
12 Sony ECM-3711 取扱説明書 ネットワークルーター 0
13 Sony AIRLINK HELIX 2140847 取扱説明書 ネットワークルーター 2
14 Sony DVS-V1616 取扱説明書 ネットワークルーター 0
15 Sony HKJ-101 取扱説明書 ネットワークルーター 0