ページ1に含まれる内容の要旨
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
SpeedTouch™ 580 Installation and Setup Guide R4.3.0
ページ4に含まれる内容の要旨
Copyright Copyright ©1999-2005 THOMSON. All rights reserved. Passing on, and copying of this document, use and communication of its contents is not permitted without written authorization from THOMSON. The content of this document is furnished for informational use only, may be subject to change without notice, and should not be construed as a commitment by THOMSON. THOMSON assumes no responsibility or liability for any errors or inaccuracies that may appear in this document. Thomson Telecom
ページ5に含まれる内容の要旨
Contents Contents About this Installation and Setup Guide ................... 5 1 Introducing the SpeedTouch™....................................7 2 Basic Installation...........................................................9 2.1 Installing your SpeedTouch™....................................................... 10 2.2 Connecting the Hardware ............................................................ 11 2.3 The SpeedTouch™ Setup CD........................................................ 13 3
ページ6に含まれる内容の要旨
Contents 5.2 LED Diagnostics........................................................................... 33 5.3 Web Diagnostics .......................................................................... 35 5.4 SpeedTouch™ Setup CD Troubleshooting ................................... 36 5.5 Wireless Setup Troubleshooting .................................................. 39 5.6 Easy Setup Troubleshooting ........................................................ 40 5.7 Reset to Factory Defaults .....
ページ7に含まれる内容の要旨
About this Installation and Setup Guide Used symbols A note provides additional information about a topic. A tip provides an alternative method or shortcut to perform an action. A caution warns you about potential problems or specific precautions that ! need to be taken. Terminology Generally, the SpeedTouch™580(i) will be referred to as SpeedTouch™ in this Installation and Setup Guide. Documentation and THOMSON continuously develops new solutions, but is also committed to improve its existin
ページ8に含まれる内容の要旨
E-DOC-CTC-20050126-0005 v1.0 6
ページ9に含まれる内容の要旨
Chapter 1 Introducing the SpeedTouch™ 1 Introducing the SpeedTouch™ Introduction In a minute you will be able to access the Internet using your SpeedTouch™580(i) This Installation and Setup Guide will show you how to set up your SpeedTouch™ and how to connect a computer or a local area network (LAN) to the Internet. Key features Your SpeedTouch™ offers you following features: A full operating system independent Internet Gateway Device Interfaces: Wi-Fi 802.11b/g USB v1.1 slave port Four
ページ10に含まれる内容の要旨
Chapter 1 Introducing the SpeedTouch™ Variants The SpeedTouch™ comes in two ADSL flavours: The ADSL POTS variant: The SpeedTouch™580 connects to an analogue Plain Old Telephone Service (POTS) line. The ADSL ISDN variant: The SpeedTouch™580i connects to an Integrated Service Digital Network (ISDN) line, enabling residences with an ISDN line to use the ADSL service. You can easily identify your variant by checking the product name printed on the identification label on the bottom of your Spe
ページ11に含まれる内容の要旨
ページ12に含まれる内容の要旨
ページ13に含まれる内容の要旨
Chapter 2 Basic Installation 2.2 Connecting the Hardware Wiring The figure below shows all possible types of connection to your SpeedTouch™. 15VAC ON/OFF 1 2 3 4 The colour coded printing on the backpanel of your SpeedTouch™ will facilitate matching the colour coded cables. 1 Use the grey DSL cable to wire the SpeedTouch™ DSL port to your telephone wall outlet or distributed filter. 2 Plug in the coaxial jack from the electric power supply adapter into the SpeedTouch™ ’15VAC’ port and the oth
ページ14に含まれる内容の要旨
Chapter 2 Basic Installation Powering the To turn on the SpeedTouch™, press the power button on the SpeedTouch™ rear panel. SpeedTouch™ During the start-up procedure, the power LED on the front panel is lit red for some seconds. As soon as the power LED is solidly lit green, your SpeedTouch™ is ready for service. After another couple of seconds, also the DSL LED will light green. If these LEDs do not light, please refer to ”Checking the LEDs” on page 33. A comprehensive LED overview can be f
ページ15に含まれる内容の要旨
ページ16に含まれる内容の要旨
Chapter 2 Basic Installation SpeedTouch™ CD menu The SpeedTouch™ CD menu will pop up automatically each time you insert the CD: Select: Setup my SpeedTouch™ to start the SpeedTouch™ Home Install Wizard allowing you to prepare your SpeedTouch™ and network for Internet connectivity. See “3.1 SpeedTouch™ Home Install Wizard” on page 16 for more information. SpeedTouch™ Maintenance to: Reconfigure your SpeedTouch™ via the Home Install Wizard. Upgrade your SpeedTouch™. Check for SpeedTouch™ up
ページ17に含まれる内容の要旨
Chapter 3 Internet Access in No Time 3 Internet Access in No Time What you need from Following configuration parameters are provided by your ISP: your ISP Your ISP’s connection service model (for example PPPoE) VPI/VCI (for example 8/35) Your user name and password to connect to the Internet Optionally your ISP may indicate the Service Profile to use in the SpeedTouch™ Home Install Wizard or Easy Setup. Internet connectivity There are different ways of setting up Internet connectivity on yo
ページ18に含まれる内容の要旨
Chapter 3 Internet Access in No Time 3.1 SpeedTouch™ Home Install Wizard Internet connection With the help of the SpeedTouch™ Home Install Wizard you will be on the Internet in a flash. setup First, the wizard will try to detect your SpeedTouch™. After connecting your PC, the wizard will configure your SpeedTouch™ and - if necessary - your PC. The Home Install Wizard was designed for Microsoft Windows operating systems and Mac OS X - in the latter case provided you will use a wired connectio
ページ19に含まれる内容の要旨
Chapter 3 Internet Access in No Time Connecting your PC The wizard will now ask you to connect the SpeedTouch™ to your PC.The next step will depend on the connection type you will use. In case of: Wireless : Go to “3.1.1 Wireless Setup” on page 22. USB: Go to “3.1.2 Installing USB drivers” on page 23. Ethernet: After you have plugged in the Ethernet cable to both the computer and the SpeedTouch™, click Next and proceed with “ Configuring the SpeedTouch™ (and your PC)” on page 18. If the wi
ページ20に含まれる内容の要旨
Chapter 3 Internet Access in No Time Configuring the Once the hardware is installed successfully and you are connected to the SpeedTouch™, the wizard will continue with the configuration of your SpeedTouch™. SpeedTouch™ (and your PC) Proceed as follows: 1 If prompted, enter the User name and Password for your SpeedTouch™ security settings and click OK. The factory default user is ‘Administrator’. Its password is blank, meaning you do not have to enter anything in the password field. It is ad
