ページ1に含まれる内容の要旨
ipRocketLink™ Model 3101 Series
ADSL2/2+ Router
Quick Start Guide
Important—This is a Class B device and is intended for use in a light industrial (commercial) or resi-
dential environment. It is not intended for use in a heavy industrial environment.
Part Number: 07M3101-QS, Rev. B Sales Office: +1 (301) 975-1000
Revised: September 23, 2011 Technical Support: +1 (301) 975-1007
E-mail: support@patton.com
WWW: www.patton.com
ページ2に含まれる内容の要旨
• Do not open the device when the power cord is connected. For sys- tems without a power switch and without an external power adapter, line voltages are present within the device when the power cord is connected. WARNING • For devices with an external power adapter, the power adapter shall be a listed Limited Power Source The mains outlet that is utilized to power the device shall be within 10 feet (3 meters) of the device, shall be easily accessible, and protected by a circuit breaker in c
ページ3に含まれる内容の要旨
Electrostatic Discharge (ESD) can damage equipment and impair electrical circuitry. It occurs when electronic printed circuit cards are improperly handled and can result in complete or intermittent failures. Do the follow- ing to prevent ESD: CAUTION • Always follow ESD prevention procedures when removing and replac- ing cards. • Wear an ESD-preventive wrist strap, ensuring that it makes good skin contact. Connect the clip to an unpainted surface of the chassis frame to safely channel unwant
ページ4に含まれる内容の要旨
PC Ethernet port Connect to LAN or Ethernet port Figure 1. Connecting the ipRocketLink to the PC’s serial port 2.2 Log in via web browser 1. Launch a Web browser on your computer. 2. Browse to “http://192.168.1.1” (the 3101’s default IP address).The login page displays. 3. Enter a username and password. The default superuser username and password are both admin. The default operator/common username and password are both user. It is recommended to change these default values after
ページ5に含まれる内容の要旨
3.0 Connect the ADSL port 1. Obtain a single-twisted-pair cable with an RJ-11 plug connector at each end. 2. Plug one end of the cable into the RJ-11socket labeled Line on the ipRocketLink Router. 3. Plug the other end of the cable into the RJ-11 wall socket that provides your DSL service. 4. When a DSL link is established, the front panel Line LED will turn on. 4.0 Additional Information Refer to the Model 3101 Series Getting Started Guide located on the CD that shipped with the
ページ6に含まれる内容の要旨
B.0 Compliance Information B.1 Compliance EMC: EN55022, Class A EN55024 Safety: IEC/EN60950-1, 2nd Edition PSTN: IEC/EN60950-1, 2nd Edition B.2 CE Declaration of Conformity Patton Electronics, Inc declares that this device is in compliance with the essential requirements and other rele- vant provisions of Directive 2004/108/EC relating to electromagnetic compatibility and Directive 2006/95/EC relating to electrical equipment designed for use within certain voltage limits. The Declar
ページ7に含まれる内容の要旨
Copyright statement Copyright © 2011, Patton Electronics Company. All rights reserved. The information in this document is subject to change without notice. Patton Electronics assumes no liability for errors that may appear in this document. Trademarks statement The term ipRocketLink is a trademark of Patton Electronics Company. All other trademarks presented in this doc- ument are the property of their respective owners. Warranty, Trademark, & Compliance Information For warranty, trademark and
ページ8に含まれる内容の要旨
NOTES ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ___________
