ページ1に含まれる内容の要旨
SmartNode 4520 and 4110 Series
VoIP Gateway Routers
Quick Start Guide
Approval—Models that are equipped with FXO interfaces have been
approved for connection to the public telecommunication network.
Zulassung—Modelle, die mit FXO Schnittstellen ausgerüstet sind, sind
für Anschaltung an das öffentliche Telekommunikationsnetz genehmigt.
Approvazione—I modelli che sono dotato con le interfacce di FXO
sono stato approvato per collegamento alla rete di
telecomunicazion pubblica.
Ap
ページ2に含まれる内容の要旨
• The SmartNode contains no user serviceable parts. The equipment shall be returned to Patton Electronics for repairs, or repaired by qualified service personnel. WARNING • Mains Voltage: Do not open the case when the power cord is connected. For systems without a power switch, line voltages are present within the power supply when the power cord is con- nected. The mains outlet that is utilized to power the SmartNode router shall be within 10 feet (3 meters) of the devic
ページ3に含まれる内容の要旨
Voice Ports FXS ETH 0/0 0/3 0/2 0/1 0/0 Voice Ports FXS ETH 0/0 ETH 0/1 0/3 0/2 0/1 0/0 2.0 Connect the SmartNode to your PC Note For factory default IP address information, see Appendix A.0 on page 8. Option 1: Connect to a network that has a DHCP server (SN4520 & SN4110). Using the included black Ethernet cable, connect the SmartNode RJ-45 Ethernet WAN port, labeled ETH0/0 (see figure 1), to an Ethernet hub or switch on the same network as your PC. WAN interface ETH0/0
ページ4に含まれる内容の要旨
2. Right-click on My Network Places and select Properties in the context menu (see figure 3). Figure 3. Displaying the Network Connections window Figure 4. Displaying the Internet Properties (TCP/IP) Properties window 3. Double-click on Local Area Connection and click on Properties to open the Internet Protocol (TCP/IP) Properties window (see figure 4). 4. Select Obtain an IP address automatically and Obtain DNS server address automatically options. 5. Click O
ページ5に含まれる内容の要旨
Option 3: Connect the SmartNode console port to your PC (SN4520 & SN4110). If your PC has an RS-232 serial COM port, you may use it to connect the SmartNode Console port. Refer to the SmartNode 4110/4520 Getting Started Guide located on the CD-ROM shipped with your SmartNode for the procedure. 3.0 Start the SmartNode Discovery Tool 1. Insert the CD included with your SmartNode into the CD drive on your PC. 2. Copy the file named SNDiscovery.exe from the CD to your PC.
ページ6に含まれる内容の要旨
4.0 Access the Command Line Interface 1. In the Discovery Tool window, select the IP address of your SmartNode. 2. Right-click the selected line, and select Telnet. 3. In the telnet window, enter the username administrator. At the password prompt simply press the enter key. The SmartNode will respond by display- ing its IP address as the command line prompt. 4. After you log in your SmartNode will be running in operator execution mode (indicated by > character i
ページ7に含まれる内容の要旨
5.0 Download a configuration example, adapt it to your network, and load it onto the SmartNode Patton provides a collection of configuration templates on the CD-ROM shipped with your SmartNode device—and also on the support page at www.patton.com/voip/appnotes.shtml. In most cases, one of these tem- plates should be similar to your application so that you can use it to speed up con- figuring the SmartNode. Simply download to your PC the configuration note that mos
ページ8に含まれる内容の要旨
6.0 Additional Information Refer to the SmartNode Series SmartWare Software Configuration Guide and the SmartNode Getting Started Guide located on the CD-ROM shipped with your SmartNode device and available online at www.patton.com/manuals. For detailed information about: • Installing, configuring, operating, and troubleshooting. • Warranty, trademark & compliance The CD-ROM also includes many freeware and shareware tools, including TFTP servers, and Telnet clients. A.
ページ9に含まれる内容の要旨
C.0 Compliance Information C.1 Compliance EMC Compliance: • FCC Part 15, Class A • EN55022, Class A • EN55024 Safety Compliance: • UL60950-1/CSA C22.2 No. 60950-1 • IEC 60950-1 • EN60950-1 • AS/NZS 60950-1 PSTN Regulatory Compliance: • FCC Part 68 • CS-03 • TBR-21 • AS/ACIF S002 • AS/ACIF S003 C.2 Radio and TV interference The SmartNode router generates and uses radio frequency energy, and if not installed and used properly—that is, in strict accordance with the
ページ10に含まれる内容の要旨
C.3 FCC Part 68 (ACTA) statement (FXO ports) This equipment complies with Part 68 of the FCC rules and the requirements adopted by ACTA. On the bottom side of this equipment is a label that contains— among other information—a product identifier in the format US:AAEQ##TXXXX. If requested, this number must be provided to the tele- phone company. The method used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and re
ページ11に含まれる内容の要旨
ment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment. Users should ensure for their own protection that the ground connections of the power utility, telephone lines and internal metallic water pipe system, are connected together. This protec- tion may be particularly important in rural areas. C.5 EC Declaration of Conformity (See section C.7 “EG-Konformitätserklärung” for German version.) Product Description: Smart
ページ12に含まれる内容の要旨
Die unterzeichnete Konformitätserklärung kann heruntergeladen werden von: www.patton.com/certifications/. C.8 Zulassung Der SmartNode ist für die Anschaltung an das öffentliche Telekommunikationsnetz zugelassen. Er darf durch jedermann an eine FXO Schnittstelle angeschlossen und in Betrieb genommen werden. Copyright statement Copyright © 2005–2006, Patton Electronics Company. All rights reserved. The information in this document is subject to change without notice. Patton Elec- tronics assume
