ページ1に含まれる内容の要旨
LevelOne
WBR-5400
MIMO Wireless 1W,4L Broadband Router
User`s Manual
Ver 1.00-0512
1
ページ2に含まれる内容の要旨
Copyright The contents of this publication may not be reproduced in any part or as a whole, stored, transcribed in an information retrieval system, translated into any language, or transmitted in any form or by any means, mechanical, magnetic, electronic, optical, photocopying, manual, or otherwise, without the prior written permission. Trademarks All products, company, brand names are trademarks or registered trademarks of their respective companies. They are used for identification pu
ページ3に含まれる内容の要旨
Table of Contents CHAPTER 1 INTRODUCTION............................................................................5 FUNCTIONS AND FEATURES........................................................................................ 5 PACKING LIST ............................................................................................................ 7 CHAPTER 2 HARDWARE INSTALLATION.....................................................8 2.1 PANEL LAYOUT .................................
ページ4に含まれる内容の要旨
APPENDIX B 802.1X SETTING.........................................................................76 APPENDIX C RESET TO FACTORY DEFAULT.............................................82 RESET TO FACTORY DEFAULT ................................................................................... 82 4
ページ5に含まれる内容の要旨
Chapter 1 Introduction Chapter 1 Introduction Chapter 1 Introduction Congratulations on your purchase of this outstanding LevelOne WBR-5400, 11g MIMO Wireless Broadband Router. This product is specifically designed for Small Office and Home Office needs. It provides a complete SOHO solution for Internet surfing, and is easy to configure and operate even for non-technical users. Instructions for installing and configuring this product can be found in this manual. Before you install
ページ6に含まれる内容の要旨
Wireless functions High speed for wireless LAN connection Up to 54Mbps data rate by incorporating Orthogonal Frequency Division Multiplexing (OFDM). Roaming Provides seamless roaming within the IEEE 802.11b (11M) and IEEE 802.11g (54M) WLAN infrastructure. IEEE 802.11b compatible (11M) Allowing inter-operation among multiple vendors. IEEE 802.11g compatible (54M) Allowing inter-operation among multiple vendors. MIMO with new MRC technology The farther away, the more advantag
ページ7に含まれる内容の要旨
When SPI Mode is enabled, the router will check every incoming packet to detect if this packet is valid. DoS Attack Detection Supported When this feature is enabled, the router will detect and log the DoS attack comes from the Internet. Advanced functions System time Supported Allow you to synchronize system time with network time server. E-mail Alert Supported The router can send its info by mail. Dynamic dns Supported At present,the router has 3 ddns.dyndns,TZO.com and dhs.
ページ8に含まれる内容の要旨
Chapter 2 Hardware Installation Chapter 2 Hardware Installation Chapter 2 Hardware Installation 2.1 Panel Layout 2.1.1. Front Panel Figure 2-1 Front Panel LED: LED Function Color Status Description Power POWER Green On Power is being applied to this product. indication System STATUS is flashed once per second to indicate system is STATUS status Green Blinking alive. indicators On The WAN port is linked. WAN port WAN Green activity Blinking The WAN port is sending o
ページ9に含まれる内容の要旨
2.1.2. Rear Panel Ports: Port Description PWR(DC) Power inlet WAN the port where you will connect your cable (or DSL) modem or Ethernet router. Port 1-4 the ports where you will connect networked computers and other devices. 9
ページ10に含まれる内容の要旨
2.2 Procedure for Hardware Installation 2. Decide where to place your Wireless Broadband Router You can place your WBR-5400, Wireless Broadband Router, on a desk or other flat surface, or you can mount it on a wall. For optimal performance, place your Wireless Broadband Router in the center of your office (or your home) in a location that is away from any potential source of interference, such as a metal wall or microwave oven. This location must be close to power and network connection
ページ11に含まれる内容の要旨
Chapter 3 Network Settings and Software Installation Chapter 3 Network Settings and Software Installation Chapter 3 Network Settings and Software Installation To use WBR-5400 correctly, you have to properly configure the network settings of your computers and install the attached setup program into your MS Windows platform (98SE/ME/2000/XP ) 3.1 Make Correct Network Settings of Your Computer The default IP address of this product is 192.168.123.254, and the default subnet mask is
ページ12に含まれる内容の要旨
Chapter 4 Configuring Wireless Broadband Router Chapter 4 Configuring Wireless Broadband Router Chapter 4 Configuring Wireless Broadband Router This product provides Web based configuration scheme, that is, configuring by your Web browser, such as Netscape Communicator or Internet Explorer. This approach can be adopted in any MS Windows, Macintosh or UNIX based platforms. 12
ページ13に含まれる内容の要旨
4.1 Start-up and Log in Activate your browser, and disable the proxy or add the IP address of this product into the exceptions. Then, type this product’s IP address in the Location (for Netscape) or Address (for IE) field and press ENTER. For example: http://192.168.123.254. After the connection is established, you will see the web user interface of this product. There are two appearances of web user interface: for general users and for system administrator. To log in as an administr
ページ14に含まれる内容の要旨
4.2 Status This option provides the function for observing this product’s working status: A. WAN Port Status. If the WAN port is assigned a dynamic IP, there may appear a “Renew” or “Release” button on the Sidenote column. You can click this button to renew or release IP manually. B. Statistics of WAN: enables you to monitor inbound and outbound packets Note: After successful login, you can switch the language in the Web-based user interface. There are four languages availa
ページ15に含まれる内容の要旨
4.3 Wizard Setup Wizard will guide you through a basic configuration procedure step by step.Press ”Next >” Setup Wizard will automatically detect your WAN type. If WAN type can not be detected successfully, “Dynamic IP Address” will be assigned. 15
ページ16に含まれる内容の要旨
Setup Wizard - Select WAN Type: For detail settings, please refer to 4.4.1 primary setup. For the rest of the steps, Setup Wizard will guide you through a basic configuration. .Press ”Next >” 16
ページ17に含まれる内容の要旨
4.4 Basic Setting 17
ページ18に含まれる内容の要旨
4.4.1 Primary Setup – WAN Type, Virtual Computers Press “Change” 18
ページ19に含まれる内容の要旨
This option is primary to enable this product to work properly. The setting items and the web appearance depend on the WAN type. Choose correct WAN type before you start. 1. LAN IP Address: the local IP address of this device. The computers on your network must use the LAN IP address of your product as their Default Gateway. You can change it if necessary. 2. WAN Type: WAN connection type of your ISP. You can click Change button to choose a correct one from the following four options: A. S
ページ20に含まれる内容の要旨
4.4.1.5 PPTP 1. My IP Address and My Subnet Mask: the private IP address and subnet mask your ISP assigned to you. 2. Server IP Address: the IP address of the PPTP server. 3. PPTP Account and Password: the account and password your ISP assigned to you. If you don'twant to change the password, keep it empty. 3. Connection ID: optional. Input the connection ID if your ISP requires it. 4. Maximum Idle Time: the time of no activity to disconnect your PPTP session. Set it to ze