ページ1に含まれる内容の要旨
ZMAXdp
Dual AMD Opteron™ SFF Barebone
User’s Manual
Version 1.0
FB246284011
ページ2に含まれる内容の要旨
IWILL ZMAXdp Contents: FCC Compliance Statement ………………………….……………………………………………..........4 Disclaimer, Trademarks and Copyright ………………………….……………………………...............5 Welcome ………………………………………………………….……………………………...............6 About this manual ..…………………………………………………………………….………….............7 About this guide ….…………………………………………………………………….………….............8 Unpacking …….………………………………………………………………….…………......................9
ページ3に含まれる内容の要旨
SFF Workstation Installation Guide Chapter 4. Mainboard Information………………………………………………………………..39 Introduction……………………………………………………………………………………………...…40 Motherboard photos…………………………………………………………………………………...…41 Motherboard layout..…………………………………………………………………………………...…43 Central processing unit and System memory………..……………………………………………...…46 Expansion slot ………………………………………………………………………………...................48 Jumpers Setting …………………………………………………………
ページ4に含まれる内容の要旨
IWILL ZMAXdp Federal Communications Commission (FCC) statement This equipment has been tested and found to comply with limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in residential installations. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in ac
ページ5に含まれる内容の要旨
SFF Workstation Installation Guide Disclaimer The information in this document is subject to change without notice. The manufacturer makes no representations or warranties regarding the contents of this manual and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. Furthermore, the manufacturer reserves the right to revise this publication or make changes in the specifications of the
ページ6に含まれる内容の要旨
IWILL ZMAXdp Copyright This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without the express written consent of the manufacturer. IWILL ©Copyright 2003
ページ7に含まれる内容の要旨
SFF Workstation Installation Guide Welcome Thank you for buying the IWILL® ZMAXdp barebone! The barebone delivers a host of new features and latest technologies making it another standout in the long line of IWILL quality motherboards! The barebone combines the powers of the AMD Opteron™ processor and the NVIDIA® nForce3 Pro250 chipset to set a new benchmark for an effective desktop platform solution. Supporting up to 2GB of system
ページ8に含まれる内容の要旨
IWILL ZMAXdp About this Manual Audience This guide provides general information and installation instructions about the IWILL ZMAXdp series Barebone workstation. This guide is intended for experienced users and integrators with hardware knowledge of personal computers. How this guide is organized This document contains the following parts: 1. Chapter 1: System Introduction This chapter gives a general descripti
ページ9に含まれる内容の要旨
SFF Workstation Installation Guide About this guide Illustrations used in this guide WARNING! Information to prevent injury to yourself when trying to complete a task. DANGER! Information to prevent damage to the components. IMPORTANT Information that you MUST follow to complete a task. NOTE Tips and additional information to aid in completing a task. Where to find more information Refer to the IWILL Websites for a
ページ10に含まれる内容の要旨
IWILL ZMAXdp Unpacking ZMAXdp Your ZMAXdp may not be supplied with all of the accessories shown, depending on the system configuration you purchased. For details on the accessories supplied with your computer, see the specifications sheet in this manual. ZMAXdp barebone unit SATA devices Power Cord IDE Device Screws and SATA ribbon power cable thermal cream cable power cable Wireles
ページ11に含まれる内容の要旨
System Introduction SFF Workstation Installation Guide Chapter 1 All about the IWILL ZMAXdp series barebone system: the front and rear panel features, and the internal layout and design. The IWILL ZMAX series barebone system includes the IWILL motherboard, a power supply, accessories and cables built into in a chassis This section shows the various external connectors on your computer to which you can attach external options,
ページ12に含まれる内容の要旨
IWILL ZMAXdp ZMAXdp Front Panel Features: The front panel of ZMAXdp features: a 5.25” empty bay, 6-in-1 card reader, two 6-pin Firewire jacks, and two USB2.0 connectors A Open H Empty Bay For Optical Drive B Microphone I Optical Drive Eject Button C Earphone J IEEE1394 (Firewire) D USB2.0 Port K Empty 3.5" FDD or Card Reader E USB2.0 Port L USB2.0 Port F Power On Button M USB2.0 Port G WLAN Antenna (WLAN V
ページ13に含まれる内容の要旨
SFF Workstation Installation Guide ZMAXdp Rear Panel Features: The back panel of your ZMAXdp contains the ports for supplied and optional accessories. The icons on the back panel locate and identify the ports on your computer. A Screws on rear I WLAN Antenna (WLAN Version Only) B Power supply J Empty AGP slot C AC Input port K Empty PCI slot D Power supply switch L Ethernet E External SATA M Line in F Serial port N Line out
ページ14に含まれる内容の要旨
IWILL ZMAXdp Internal Features The figure below shows the system from side. The standard components (Motherboard, Heatsink for processors, power supply…) are already installed. Actual products may look different from the photo. 14 User’s Manual
ページ15に含まれる内容の要旨
Assembling the System SFF Workstation Installation Guide Chapter 2 Step-by-step instructions on how to install basic components. This section outlines how to install and configure your ZMAXdp. Refer to the following mainboard layout to help you to identify various jumpers, connectors, slots, and ports. Then follow these steps designed to guide you through a quick and correct Installation of your system. IWILL has designed the
ページ16に含まれる内容の要旨
IWILL ZMAXdp Removing the cover 1. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. 2. Remove the WLAN antenna on the top of the computer 3. Release the three screws at the rear of the left side cover 4. Separate the case and chassis cover: use your thumbs to pull it off, from the front to the back, then l
ページ17に含まれる内容の要旨
SFF Workstation Installation Guide Lifting the casing cover Separate the case and chassis cover: use your thumbs to pull it off, from the front to the back, then lift it off the chassis. If you remove the side panel immediately after you shut down your computer, the components may be too hot to touch. Wait until the internal parts of the system unit cool down before you attempt to remove the side panel.
ページ18に含まれる内容の要旨
IWILL ZMAXdp Turn over the drive holder Release the screws from the CDROM/ HDD rack with a screw driver. Release the screws from the rack Release the two screws holding the rack to the casing. Set one screws aside.. Remove this screw Remove another screw holding the rack to the casing and set it aside. Pull drive holder up Draw the drive holder a little bit. Pull up the holder, fix the rack on the casing and
ページ19に含まれる内容の要旨
SFF Workstation Installation Guide Remove the drive holder Please remove the drive holder entirely. It would be easier to install graphic card, CPUs and memory. Release the screws from the CDROM/ HDD rack with a screw driver. Release the screw from the rack Release the two screws holding the rack to the casing. Set one screws aside.. Remove this screw Remove another screw holding the rack to the casing and set it aside. Rem
ページ20に含まれる内容の要旨
IWILL ZMAXdp Remove the pre-installed heatsink assembly To install the CPU, it is necessary to remove the pre-installed heatsink module. Please remove six screws from heatsink. Gently handle the heatsink module. Avoid hitting, falling or throwing down the heatsink. Remove the screws (marked in circles) 20
