ページ1に含まれる内容の要旨
Wireless LAN Access Point
with 5-Port Switch
EW-7205APS
User’s Manual
ページ2に含まれる内容の要旨
Table of Contents Chapter 1 Introduction............................................................................. 1 1.1 Package Contents.......................................................................................... 1 1.2 Features ......................................................................................................... 2 1.3 Specifications................................................................................................ 2 1.4 Physical Descrip
ページ3に含まれる内容の要旨
Introduction Chapter 1 Introduction This product is a Wireless LAN Access Point with 5-port 10/100Mbps Fast Ethernet Switch, which allows you to build your wireless network without buying an additional hub or switch. It is the ideal product that provides you the best solution for building both wireless network and 10/100Mbps Fast Ethernet backbone. The product supports advanced user authentication including 64/128-bit WEP Encryption and IEEE 802.1X ensures a high level of security for w
ページ4に含まれる内容の要旨
Introduction 1.2 Features Complies with the IEEE 802.11b (DSSS) 2.4GHz specification. High data rate 11, 5.5, 2 and 1Mbps network speed. Seamlessly integrate wireless and wired Ethernet LAN networks. Provides an internal 5-port switch for wired Ethernet connection. Detachable external antenna provides users flexibility to install the wireless network with high gain antenna. Auto rate fallback in case of obstacles or interferences. Provides 64/128-bit WEP Data Encryption functi
ページ5に含まれる内容の要旨
Introduction Temperature: Operating: 32~131°F (0~55°C) Storage: -4~158°F(-20~70°C) Humidity: 0-90% (Noncondensing) Certification: FCC, CE 1.4 Physical Description Front Panel On the Access Point’s front panel there are LED lights that inform you of the Access Point’s current status. Below is an explanation of each LED. LED Color Status Description Lit Power is supplied. Power Green Off No Power. Wireless Flash Antenna is transmitting or receiving data. Green TX
ページ6に含まれる内容の要旨
Introduction Antenna Connector This round connection is standard Reverse SMA connector where any antennas with Reverse SMA connector can connect to the Access Point. DC Adapter Port Insert the power jack of the power adapter into this port. 10/100Mbps The Access Point’s LAN ports are where you connect your LAN’s PCs. Uplink Port Using this port connects to Ethernet network devices, such as a hub, switch, or router directly. Reset The Reset button allows you to do
ページ7に含まれる内容の要旨
Wireless LAN Access Point Connection Chapter 2 Wireless LAN Access Point Connection 1. Locate an optimum location for the Wireless LAN Access Point. The best location for your Access Point is usually at the center of your wireless network, with line of sight to all of your mobile stations. 2. Connect the Wireless LAN Access Point to your 10/100Mbps network. Connect one end of standard UTP cable to the Access Point’s Uplink Port and connect the other end of the cable to a switch or a h
ページ8に含まれる内容の要旨
Wireless LAN Access Point Configuration Chapter 3 Wireless LAN Access Point Configuration 3.1 Getting Started This Access Point provides web-based configuration tool allowing you to configure from wired or wireless stations. Follow the instructions below to get started configuration. From Wired Station 1. Make sure your wired station is in the same subnet with the Access Point. The default IP Address and Sub Mask of the Access Point is: Default IP Address: 192.168.2.1 Default Subne
ページ9に含まれる内容の要旨
Wireless LAN Access Point Configuration • IP Address: Select Specify an IP Address. Specify the IP Address and Subnet Mask as following example. IP Address: 192.168.2.3 (any IP address within 192.168.2.2~192.168.2.254 is available, do not setup 192.168.2.1) Subnet Mask: 255.255.255.0 8. Reboot the PC. Your PC will now have the IP Address you specified. 1b) Windows 2000 1. Click the Start button and select Settings, then click Control Panel. The Control Panel window will appear. 2
ページ10に含まれる内容の要旨
Wireless LAN Access Point Configuration • IP Address: Select Specify an IP address. Specify the IP Address and Subnet Mask as following example. IP Address: 192.168.2.3 (any IP address within 192.168.2.2~192.168.2.254 is available, do not setup 192.168.2.1) Subnet Mask: 255.255.255.0 • DNS: Let all fields are blank. • WINS: Let all fields are blank. • Routing: Let all fields are blank. 7. Click OK to confirm the setting. Your PC will now have the IP Address you specified. 2. Ente
ページ11に含まれる内容の要旨
Wireless LAN Access Point Configuration From Wireless Station 1. Make sure your wireless station is in the same subnet with the Access Point. Please refer to the step 1 above for configuring the IP Address and Sub Mask of the wireless station. 2. Connect to the Access Point. The Access Point’s ESSID is “default” and the WEP Encryption function is disabled. Make sure your wireless station is using the same ESSID as the Access Point and associate your wireless station to the Access Point
ページ12に含まれる内容の要旨
Wireless LAN Access Point Configuration 3.2.2 Channel and ESSID You can set parameters that are used for the wireless stations to connect to this Access Point. The parameters include ESSID, Transmission Rate, Basic Rate and Channel. Parameter Description ESSID The ESSID (up to 32 printable ASCII characters) is the unique name identified in a WLAN. The ID prevents the unintentional merging of two co-located WLANs. Please make sure that the ESSID of all stations in the network are
ページ13に含まれる内容の要旨
Wireless LAN Access Point Configuration Parameter Description The lowest data transmission speed supports by the Access Point. If All Basic Rate is selected, the Access Point will automatically select the optimum rate allowed in the environment. The default value is “1~2Mbps”. Channel Select the appropriate channel from the list provided to correspond with your network settings. Channels differ from country to country. Channel 1-11 (North America) Channel 1-14 (Japan) Channel 1-1
ページ14に含まれる内容の要旨
Wireless LAN Access Point Configuration Parameter Description WEP Mode You can select the 64-bit or 128-bit to encrypt transmitted data. Larger WEP key length will provide higher level of security, but the throughput will be lower. You also can select Disable to transmit data without encryption. 12
ページ15に含まれる内容の要旨
Wireless LAN Access Point Configuration 13
ページ16に含まれる内容の要旨
Wireless LAN Access Point Configuration Parameter Description Passphrase Enter a maximum of 32 alphanumeric characters in the text box and press Generate button, the Access Point will generate a WEP key automatically (refer to the 128-bit screen, the key is displayed after the Access Point generate the key for the wording “test”). It is easy for user to setup the WEP key. Note that this passphrase may not work with some wireless products due to possible incompatibility with other vendor
ページ17に含まれる内容の要旨
Wireless LAN Access Point Configuration Parameter Description Filtering Enable or disable the MAC Address Filtering function. Setting You can select to permit or prohibit the MAC addressed listed in the MAC Address Filtering Table to access your wireless LAN. MAC Address Filtering Table There are 32 sets MAC Address you can set here. Fill the MAC Addresses of wireless stations you want to permit or prohibit to access your network in this table. Click Apply button at the botto
ページ18に含まれる内容の要旨
Wireless LAN Access Point Configuration to connect to the Access Point should be authenticated by an Authentication Server. The Authentication Server identifies the wireless station by a set of user name and password, only wireless stations provide correct user name and password can connect to the Access Point and access to the network. This Access Point can not only use Remote RADIUS Server to authenticate the wireless stations, but also utilize a built-in propriety authentication ser
ページ19に含まれる内容の要旨
Wireless LAN Access Point Configuration Parameter Description Enable IEEE 802.1X Enable or disable the IEEE 802.1X function. Session Idle Timeout If the wireless station doesn’t transmit or receive data for a period after authentication, the Access Point will force the wireless station to the unauthenticated status and the wireless station has to authenticate again. The default session idle timeout is 300 seconds. Re-Authentication Period Re-Authentication Period defines the t
ページ20に含まれる内容の要旨
Wireless LAN Access Point Configuration Parameter Description Server Type There are two kinds of servers supported by the Access Point including Remote RADIUS Server and TINY Server. You have to build a Remote RADIUS Server if RADIUS Server is selected. You can build a RADIUS Server by installing Windows 2000 with Internet Authentication Server. If TINY Server is selected, the Access Point can be the authentication server itself and you don’t need to build another authentication server.
