ページ1に含まれる内容の要旨
Cisco uBR10-LCP2-MC16C/MC16E/MC16S Cable
Interface Card for the Cisco uBR10012 Router
OL-2872-02
June 2005
Note The Cisco uBR10-LCP2-MC16x (C, E, S) cable interface line cards are end of sale. For additional
information, refer to END-OF-LIFE NOTICE, NO. 2600 at the following location:
http://www.cisco.com/en/US/products/hw/cable/ps2209/prod_eol_notice0900aecd80183921.html
This document describes the Cisco uBR10-LCP2-MC16C, the Cisco uBR10-LCP2-MC16E, and the
Cisco uBR10-LCP2-MC16S cable inter
ページ2に含まれる内容の要旨
Cisco uBR10-LCP2-MC16C/MC16E/MC16S Overview Cisco uBR10-LCP2-MC16C/MC16E/MC16S Overview The cable interface line cards, together with external IF-to-RF upconverters, serve as the RF interface between the cable headend and DOCSIS/EuroDOCSIS-based cable modems. The Cisco uBR10-LCP2-MC16C, the Cisco uBR10-LCP2-MC16E, and the Cisco-LCP2-MC16S cable interface line cards are a combination of two components: � Cisco uBR-MC16x (MC16C, MC16E, and MC16S) cable interface line cards—Provide one downstr
ページ3に含まれる内容の要旨
uBR-MC16C +42 dBmV Cisco uBR10-LCP2-MC16C/MC16E/MC16S Overview The cards are inserted into and removed from the Cisco uBR10012 chassis as a single logical and physical unit. All Cisco uBR10-LCP2-MC16x cable interface line cards support online insertion and removal (OIR). OIR uses the MAC address assigned to the Cisco uBR10-LCP2 adapter card, allowing you to replace any Cisco uBR-MC16x cable interface line card installed on the adapter card without losing the configuration information. Not
ページ4に含まれる内容の要旨
Cisco uBR10-LCP2-MC16C/MC16E/MC16S Overview The default modulations are: � 64 quatrature amplitude modulations (QAM) for downstream. � quadrature amplitude phase-shift keying (QPSK) for upstream. DOCSIS and EuroDOCSIS Data Rates and Modulation Schemes Cisco cable interface line cards are configured in a number of different upstream combinations based on the card used, your cable network, and the anticipated subscription and service levels. Table 2 lists the data rates and modulation schemes
ページ5に含まれる内容の要旨
Cisco uBR10-LCP2-MC16C/MC16E/MC16S Overview Cisco uBR10-LCP2-MC16E The Cisco uBR10-LCP2-MC16E cable interface line card output is +40 dBmV +/– 3 dB and supports all EuroDOCSIS upstream channel widths described in Table 2 on page 4. The card is configured identically to the Cisco uBR-MC16E cable interface line card. While all other Cisco cable interface line cards transmit downstream signals to upconverters by using the 44-MHz frequency, the Cisco uBR10-LCP2-MC16E transmits downstream IF si
ページ6に含まれる内容の要旨
CH OC-12-DSO SM-IR CH OC-12-DSO SM-IR CH OC-12-DSO SM-IR uBR-MC16C +42 dBmV uBR-MC16C +42 dBmV uBR-MC16C +42 dBmV uBR-MC16C +42 dBmV uBR-MC16C +42 dBmV uBR-MC16C +42 dBmV uBR-MC16C +42 dBmV uBR-MC16C +42 dBmV ENABLED ENABLED ENABLED ENABLED ENABLED ENABLED ENABLED ENABLED US0 US0 US1 US0 US1 US2 US0 US1 US2 US3 US0 US1 US2 US3 US4 US0 US1 US2 US3 US4 US5 US0 US1 US2 US3 US4 US5 DS US0 US1 US2 US3 US4 US5 DS US1 US2 US3 US4 US5 DS US2 US3 US4 US5 DS US3 US4 US5 DS US4 US5 DS US5 DS DS FAIL FAIL F
ページ7に含まれる内容の要旨
uBR-MC16C +42 dBmV Cisco uBR10-LCP2-MC16C/MC16E/MC16S Overview Figure 3 Cisco uBR10-LCP2-MC16C Cable Interface Line Card Components LCP2 connector MC16C connector L-Bracket Guide Ejector tab Backplane connector Ejector Captive screw L-Bracket Handle nut and washer Guide Ejector tab Captive screw Ejector Figure 4 shows the faceplate for the Cisco uBR10-LCP2-MC16C cable interface line card. Figure 4 Cisco uBR10-LCP2-MC16C Faceplate uBR-MC16C +42 dBmV The Cisco uBR10-LCP2-MC16C cable interface l
ページ8に含まれる内容の要旨
Cisco uBR10-LCP2-MC16C/MC16E/MC16S Overview Figure 6 shows the faceplate for the Cisco uBR10-LCP2-MC16S cable interface line card. Figure 6 Cisco uBR10-LCP2-MC16S Faceplate uBR - MC16S +42 dBmV The Cisco uBR10-LCP2-MC16S cable interface line card has one downstream port and six upstream ports. The upstream ports are labeled US0 through US5. The downstream port is labeled DS. There are six LEDs labeled MGR ACT (manager active) next to each upstream port. See Table 3 for a description of the
ページ9に含まれる内容の要旨
Technical Specifications Table 4 Cisco uBR-MC16x Cable Interface Line Card LEDs (Continued)and Their Functions (Continued) LED Status Description Downstream Green Downstream path is enabled and is configured (each downstream port). Off Either the port is not properly configured or is shut down, or the slot is not working. MGR ACT Green Spectrum management activity on the channel. (uBR-MC16S only) Off Spectrum management is not active. Technical Specifications Table 5 lists the specifications
ページ10に含まれる内容の要旨
Safety Information and Warnings Table 5 Cisco uBR10-LCP2-MC16C/MC16E/MC16S Cable Interface Line Card Specifications Description Specifications Operating altitude –197 to 13,123 ft (– 60 to 4000 m) Cisco IOS software minimum � Cisco uBR10-LCP2-MC16C—Cisco IOS Release 12.2(4)XF or requirements a later release � Cisco uBR10-LCP2-MC16E—Cisco IOS Release 12.2(4)XF or a later release � Cisco uBR10-LCP2-MC16S—Cisco IOS Release 12.2(8)BC2 or a later release 1. British Thermal Units Safety Informat
ページ11に含まれる内容の要旨
Safety Information and Warnings Following are guidelines for preventing ESD damage: � Always use an ESD-preventive wrist or ankle strap and ensure that it makes good skin contact. Before removing a card from the chassis, connect the equipment end of the strap to a bare metal, unpainted surface on the chassis or rack-mount. � Handle components by the carrier edges only; avoid touching the card components or any connector pins. � When removing a module, place it on an antistatic surface or i
ページ12に含まれる内容の要旨
Safety Information and Warnings Attention IMPORTANTES INFORMATIONS DE SÉCURITÉ Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des avertissements figurant dans les consign
ページ13に含まれる内容の要旨
Safety Information and Warnings ¡Advertencia! INSTRUCCIONES IMPORTANTES DE SEGURIDAD Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña a este dispositivo. GUARDE
ページ14に含まれる内容の要旨
Safety Information and Warnings Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham
ページ15に含まれる内容の要旨
Safety Information and Warnings Cisco uBR10-LCP2-MC16C/MC16E/MC16S Cable Interface Card for the Cisco uBR10012 Router OL-2872-02 15
ページ16に含まれる内容の要旨
Removing and Replacing a Cisco uBR10-LCP2-MC16x Cable Interface Line Card Removing and Replacing a Cisco uBR10-LCP2-MC16x Cable Interface Line Card Note This procedure applies to the Cisco uBR10-LCP2-MC16C, the Cisco uBR10-LCP2-MC16E, and the Cisco uBR10-LCP2-MC16S cable interface line cards. To remove and replace an individual cable interface line card you need the following tools and parts: � Replacement cable interface line card (order number UBR10-LCP2-MC16C=, UBR10-LCP2-MC16E=, UBR10-L
ページ17に含まれる内容の要旨
Removing and Replacing a Cisco uBR10-LCP2-MC16x Cable Interface Line Card Unpacking a Cisco uBR10-LCP2-MC16x Cable Interface Line Card Tip Make sure that you are using the ESD-preventive wrist strap. Step 1 Open the shipping carton by cutting the packing tape along the flaps on the top of the box. Step 2 Remove the Cisco uBR10-LCP2-MC16x cable interface line card from the packaging. Step 3 Place the card on an antistatic surface. Removing a Cisco uBR10-LCP2-MC16x Cable Interface Line Card Tip
ページ18に含まれる内容の要旨
CH OC-12-DSO SM-IR CH OC-12-DSO SM-IR CH OC-12-DSO SM-IR uBR-MC16C +42 dBmV uBR-MC16C +42 dBmV uBR-MC16C +42 dBmV uBR-MC16C +42 dBmV uBR-MC16C +42 dBmV uBR-MC16C +42 dBmV uBR-MC16C +42 dBmV uBR-MC16C +42 dBmV ENABLED ENABLED ENABLED ENABLED ENABLED ENABLED ENABLED ENABLED US0 US0 US1 US0 US1 US2 US0 US1 US2 US3 US0 US1 US2 US3 US4 US0 US1 US2 US3 US4 US5 US0 US1 US2 US3 US4 US5 DS US0 US1 US2 US3 US4 US5 DS US1 US2 US3 US4 US5 DS US2 US3 US4 US5 DS US3 US4 US5 DS US4 US5 DS US5 DS DS FAIL FAIL F
ページ19に含まれる内容の要旨
uBR - MC28C uBR - MC28C uBR - MC28C uBR - MC28C CH OC-12-DSO SM-IR CH OC-12-DSO SM-IR CH OC-12-DSO SM-IR uBR-MC16C +42 dBmV uBR-MC16C +42 dBmV uBR-MC16C +42 dBmV uBR-MC16C +42 dBmV uBR-MC16C +42 dBmV uBR-MC16C +42 dBmV uBR-MC16C +42 dBmV uBR-MC16C +42 dBmV ENABLED ENABLED ENABLED ENABLED ENABLED ENABLED ENABLED ENABLED US0 US0 US1 US0 US1 US2 US0 US1 US2 US3 US0 US1 US2 US3 US4 US0 US1 US2 US3 US4 US5 US0 US1 US2 US3 US4 US5 DS US0 US1 US2 US3 US4 US5 DS US1 US2 US3 US4 US5 DS US2 US3 S4 U US5 D
ページ20に含まれる内容の要旨
CH OC-12-DSO SM-IR CH OC-12-DSO SM-IR CH OC-12-DSO SM-IR uBR-MC16C +42 dBmV uBR-MC16C +42 dBmV uBR-MC16C +42 dBmV uBR-MC16C +42 dBmV uBR-MC16C +42 dBmV uBR-MC16C +42 dBmV uBR-MC16C +42 dBmV uBR-MC16C +42 dBmV uBR-MC16C +42 dBmV ENABLED ENABLED ENABLED ENABLED ENABLED ENABLED ENABLED ENABLED ENABLED US0 US0 US1 US0 US1 US2 US0 US1 US2 US3 US0 US1 US2 US3 US4 US0 US1 US2 US3 US4 US5 US0 US1 US2 US3 US4 US5 DS US0 US1 US2 US3 US4 US5 DS US1 US2 US3 US4 US5 DS US2 US3 US4 US5 DS US3 US4 US5 DS US4 U
