ページ1に含まれる内容の要旨
Cisco 12010, Cisco 12410, and
Cisco 12810 Router Unpacking
Instructions
This document contains instructions for unpacking the Cisco 12010, Cisco 12410,
and Cisco 12810 routers. After you unpack the system, refer to the Cisco 12010,
Cisco 12410, and Cisco 12810 routers Installation and Configuration Guide for
more information.
This document includes the following topics:
• Before Unpacking the Router, page 2
� Tools and Equipment, page 3
� Unpacking the Router, page 3
� Repacking the Route
ページ2に含まれる内容の要旨
Before Unpacking the Router Before Unpacking the Router Figure 1 shows the router on a shipping pallet. A fully configured system can weigh as much as 275 pounds (124.74 kg), not counting the additional weight of the pallet and packaging materials. Before unpacking the system, you should carefully plan the site location of the router and the method you will use to move it into position. Figure 1 Router on a Shipping Pallet Cisco 12010, Cisco 12410, and Cisco 12810 Router Unpacking Instru
ページ3に含まれる内容の要旨
Tools and Equipment Tools and Equipment You need the following items and tools: � 3/16-inch flat-blade screwdriver � 1/4-inch flat-blade screwdriver � 9/16-inch (14-mm) wrench � 10-mm wrench (open-end or socket) � Wire cutters � Pliers Unpacking the Router This section explains how to unpack the router from the shipping pallet. Figure 2 shows the main packing material and accessory kit container. The accessory tray that fits on top of the cushioning contains: � Front and midtrack-mount bra
ページ4に含まれる内容の要旨
Unpacking the Router Figure 2 Router Package Components Cap Outer tube Accessory tray Top cushion cap Front hold down bracket Rear hold down bracket Cisco 12010, Cisco 12410, and Cisco 12810 Router Unpacking Instructions 78-16075-02 4 50834
ページ5に含まれる内容の要旨
REMOVE TIE WRAP Unpacking the Router Step 1 Cut the straps securing the router to the pallet (see Figure 1). Step 2 Refer to Figure 2 for the following steps: a. Remove the top cap. b. Lift off the outer shipping tube. c. Remove the accessory tray. d. Remove the top cushion cap. Step 3 Remove the bolts securing the two front-side hold-down brackets to the pallet. Step 4 Remove the bolts securing the rear hold-down bracket to the pallet. If you are installing an enhanced version of the router
ページ6に含まれる内容の要旨
REMOVE Unpacking the Router Step 6 Open the front door and remove the labels (labeled REMOVE) that protect the rubber bumpers during shipment (Figure 4). Close the front door. Figure 4 Removing the Rubber Bumper Shipping Label Step 7 Your Cisco router is ready for installation. For installation instructions, see the Cisco 12010, Cisco 12410, and Cisco 12810 routers Installation and Configuration Guide (see Obtaining Documentation, page 8). Cisco 12010, Cisco 12410, and Cisco 12810 Router
ページ7に含まれる内容の要旨
Repacking the Router Repacking the Router This section describes how to repack your Cisco router into the shipping container. This procedure assumes you have the pallet, packing material, and hardware you saved when the chassis was unpacked. Step 1 Place the router on a Cisco 12010 series shipping pallet. Step 2 Secure the side and rear brackets to the pallet using the bolts and screws you saved when the chassis was unpacked (see Figure 2). Step 3 Tighten all of the captive screws on the
ページ8に含まれる内容の要旨
Regulatory, Compliance, and Safety Information Regulatory, Compliance, and Safety Information The complete list of translated safety warnings and agency approvals is available in the Regulatory Compliance and Safety Information for Cisco 12000 Series Internet Routers publication (Document Number 78-4347-xx). Obtaining Documentation Cisco documentation and additional literature are available on Cisco.com. Cisco also provides several ways to obtain technical assistance and other technical
ページ9に含まれる内容の要旨
Obtaining Documentation the DVD, you have access to the same documentation that is found on the Cisco website without being connected to the Internet. Certain products also have .pdf versions of the documentation available. The Product Documentation DVD is available as a single unit or as a subscription. Registered Cisco.com users (Cisco direct customers) can order a Product Documentation DVD (product number DOC-DOCDVD=) from the Ordering tool or Cisco Marketplace. Cisco Ordering tool:
ページ10に含まれる内容の要旨
Documentation Feedback Documentation Feedback You can rate and provide feedback about Cisco technical documents by completing the online feedback form that appears with the technical documents on Cisco.com. You can send comments about Cisco documentation to bug-doc@cisco.com. You can submit comments by using the response card (if present) behind the front cover of your document or by writing to the following address: Cisco Systems Attn: Customer Document Ordering 170 West Tasman Drive San
ページ11に含まれる内容の要旨
Obtaining Technical Assistance Note Use the Cisco Product Identification (CPI) tool to locate your product serial number before submitting a web or phone request for service. You can access the CPI tool from the Cisco Technical Support & Documentation website by clicking the Tools & Resources link under Documentation & Tools. Choose Cisco Product Identification Tool from the Alphabetical Index drop-down list, or click the Cisco Product Identification Tool link under Alerts & RMAs. The C
ページ12に含まれる内容の要旨
Obtaining Additional Publications and Information Definitions of Service Request Severity To ensure that all service requests are reported in a standard format, Cisco has established severity definitions. Severity 1 (S1)—Your network is “down,” or there is a critical impact to your business operations. You and Cisco will commit all necessary resources around the clock to resolve the situation. Severity 2 (S2)—Operation of an existing network is severely degraded, or significant aspects
ページ13に含まれる内容の要旨
Obtaining Additional Publications and Information Cisco products and solutions, as well as network deployment and troubleshooting tips, configuration examples, customer case studies, certification and training information, and links to scores of in-depth online resources. You can access Packet magazine at this URL: http://www.cisco.com/packet � iQ Magazine is the quarterly publication from Cisco Systems designed to help growing companies learn how they can use technology to increase rev
ページ14に含まれる内容の要旨
Obtaining Additional Publications and Information This document is to be used in conjunction with the documents listed in the Cisco12010, Cisco 12410, and Cisco 12810 Router Installation and Configuration Guide. CCVP, the Cisco logo, and the Cisco Square Bridge logo are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn is a service mark of Cisco Systems, Inc.; and Access Registrar, Aironet, BPX, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, Cisco, th
