ページ1に含まれる内容の要旨
ATM Line Card Installation and Configuration
This hardware installation and configuration note contains instructions for installing, configuring, and
troubleshooting Asynchronous Transfer Mode (ATM) line cards on supported Cisco 12000 series
routers.
Contents
This installation and configuration note includes the following sections:
• Important Information, page 1
Product Overviews, page 4
Preparing for Installation, page 7
Removing and Installing a Line Card, page 8
Line Card Cable
ページ2に含まれる内容の要旨
Important Information Hardware Revision Requirements, page 3 Related Documentation, page 4 ATM Line Card Product Numbers Table 1 lists the Cisco product numbers to which this publication applies. Table 1 ATM Line Card Product Numbers ATM Line Card Cisco Product Number 1-port OC-12c/STM-4c multimode LC-1OC12/ATM-MM= 1-port OC-12c/STM-4c single-mode LC-1OC12/ATM-SM= 4-port OC-3c/STM-1 multimode 4OC3/ATM-MM-SC= 4-port OC-3c/STM-1 intermediate-reach 4OC3/ATM-IR-SC= 4-port OC-12c/STM-4c multi
ページ3に含まれる内容の要旨
Important Information Table 2 lists the Cisco IOS releases and other software components that are compatible with the various ATM line cards. Table 2 ATM Line Card and Software Component Compatibility ATM Line Card Compatible Cisco IOS Release 1-port OC-12c/STM-4c 11.2(9) or later 4-port OC-3c/STM-1 11.2(4)GS1 or later 4-port OC-12c/STM-4c 12.0(13)S or later 12.0 S release 8-port OC-3c/STM-1 12.0(22)S or a later 12.0 S release 4-port OC-3c/STM-1 ISE 12.0(26)S2, 12.0(27)S1 or a later 12.0 S
ページ4に含まれる内容の要旨
Product Overviews Related Documentation This publication describes the basic installation and configuration of a ATM line card. For complete software and ATM configuration information, refer to the following publications: Cisco 12000 Series Router Installation and Configuration Guides Cisco 12000 Series Internet Router Configuration Guide for Cisco IOS Release 12.0S Cisco IOS Configuration Fundamentals Configuration Guide Cisco IOS Configuration Fundamentals Command Reference Cisc
ページ5に含まれる内容の要旨
Product Overviews 4-port OC-3c/STM-1 ATM Line Card Overview The 4-port OC-3c/STM-1 ATM line card interfaces with the switch fabric of the Cisco 12000 Series Router. It provides four 155-Mbps OC-3c/STM-1c duplex SC single-mode or multimode SONET/SDH connections. This connection is concatenated, which provides for increased efficiency by eliminating the need to partition the bandwidth. Figure 2 shows the single-mode, intermediate-range 4-port OC-3c/STM-1 ATM line card. Figure 2 4-port OC-
ページ6に含まれる内容の要旨
Product Overviews 8-port OC-3c/STM-1 ATM Line Card Overview The 8-port OC-3c/STM-1 ATM line card supports traffic shaping, and delivers line rate OC-3c/STM-1 bandwidth while performing traffic shaping and per-virtual circuit (VC) queueing. It also supports per-VC Modified Deficit Round Robin (MDRR) and per-VC low latency queueing (LLQ). MDRR is implemented on a per-VC basis, with up to eight queues per VC. One of the queues is a low latency queue. Both per-VC WRED and per-VC MDRR are perf
ページ7に含まれる内容の要旨
Preparing for Installation Figure 5 shows the front view of the 4-port ISE ATM line card. Figure 5 4-port ISE ATM Line Card 3 LED DENOTATION ACTIVE CARRIER RX CELL Cisco Systems, Inc. 170 W Tasman Drive San Jose, Ca 95134 CLEAN Manufactured CONNECTOR xxxxxxxx xxxx: WITH ALCOHOL CNS68V4AAA Complies with 21 CFR WIPES BEFORE Chapter 1, Subchapter J CONNECTING 4OC12X/ATM-MM-SC 2 1 4 1 Ejector lever 3 Status LEDs 2 Port 0 4 Display LEDs Preparing for Installation Before you begin the installatio
ページ8に含まれる内容の要旨
Removing and Installing a Line Card Preventing Electrostatic Discharge Electrostatic discharge (ESD) damage, which can occur when electronic cards or components are improperly handled, results in complete or intermittent failures. Electromagnetic interference (EMI) shielding is an integral component of the line card. Cisco recommends using an ESD-preventive strap whenever you are handling network equipment or one of its components. The following are guidelines for preventing ESD damage:
ページ9に含まれる内容の要旨
Removing and Installing a Line Card Note The installation and removal procedure for the ATM line card is different for the Cisco 12008 and Cisco 12012 routers than for the other Cisco 12000 series routers. Make sure you refer to the procedure that corresponds to your router chassis. Caution To avoid erroneous failure messages, remove or insert only one line card at a time. After inserting or removing a line card, allow at least 15 seconds before removing or inserting another line card, so
ページ10に含まれる内容の要旨
Removing and Installing a Line Card Caution When you remove a line card, always use the ejector levers to ensure that the connector pins disconnect from the backplane in the sequence expected by the router. Any card that is only partially connected to the backplane can halt the router. When you install a line card, always use the ejector levers to ensure that the card is correctly aligned with the backplane connector; the connector pins should make contact with the backplane in the corr
ページ11に含まれる内容の要旨
ALARM 1 ALARM 2 ALARM OC-12/STM-4 POS OC-12/STM-4 ATM Q OC-3/STM-POS GIGABIT ROUTE PROCESSOR Q OC-3/STM-POS CRITICAL MAJOR MINOR ACO/LT FAIL ENABLED CSC 0 1 0 SFC 1 2 0 ACTIVE 0 CARR R IE RX CELL ACTIVE CARRIER 0 RX PKT ACTIVE CARRIER RX CELL EJECT 1 SLOT-1 SLOT-0 ACTIVE RESET CARRIER RX PKT AUX 2 ACTIVE CARRIER RX PKT CONSOLE 3 ACTIVE CARRIER RX PKT COLL 0 RX LINK ACTIVE TX CARRIER RX PKT RJ-45 MII 1 ACTIVE CARRIER RX PKT 2 ACTIVE CARRIER RX PKT 3 ACTIVE CARRIER RX PKT Removing and Installing
ページ12に含まれる内容の要旨
Removing and Installing a Line Card Note When removing the 4-port ISE ATM line card, take into account that it weighs approximately 13.2 lb (6 kg). Removing the Blank Filler This procedure only applies to 4-port ISE ATM line cards in Cisco 12008 and Cisco 12012 routers. Because the 4-port ISE ATM line card is wider than the line card slots in the Cisco 12008 and Cisco 12012 Routers, the line card uses the space of two slots. The blank filler (part number: 4OC12X/ATM-BLANK) is used to fill
ページ13に含まれる内容の要旨
A TX INNER RX OUTER B TX INNER RX OUTER Removing and Installing a Line Card Step 1 Choose an available pair of slots for the line card, and verify that the fiber-optic interface cables for the line card are long enough for you to reach the line card ports and connect the line card to any external equipment. Step 2 Grasp the faceplate of the blank filler with one hand and place your other hand under the blank filler; position the card for insertion into the rightmost card cage slot of the
ページ14に含まれる内容の要旨
CLASS 1 LASER PRODUCT PRODUCTO LASER DE CLASSE 1 PRODUIT LASER DE CLASSE 1 CLEAN CONNECTOR LASERPRODUKT DER KLASSE 1 WITH ALCOHOL WIPES BEFORE CONNECTING A TX INNER RX OUTER B TX INNER RX OUTER 2CHOC-12/DS3-IR-SC GIGABIT ROUTE PROCESSOR EJECT SLOT-1 SLOT-0 ACTIVE RESET CARRIER RX PKT AUX ACTIVE CARRIER CONSOLE COLL RX LINK TX RJ-45 MII Removing and Installing a Line Card To ensure that there is adequate space for the ATM line card, tighten the captive installation screws on the blank fille
ページ15に含まれる内容の要旨
Removing and Installing a Line Card Note In Cisco 12008 and Cisco 12012 Routers, the 4-port ATM ISE line card uses a pair of line card slots. You must install the blank filler into the rightmost slot of the pair before you can install the 4-port ATM ISE line card. Caution The router may indicate a hardware failure if you do not follow proper procedures. Remove or insert only one line card at a time. Allow at least 15 seconds for the router to complete the preceding tasks before removing
ページ16に含まれる内容の要旨
Removing and Installing a Line Card Caution When you install a line card, always use the ejector levers to ensure that the card is correctly aligned with the backplane connector, the card connector pins make contact with the backplane in the correct order, and the card is fully seated in the backplane. A card that is only partially seated in the backplane can cause the router to hang and subsequently crash. Step 5 Simultaneously pivot both ejector levers toward each other until they are p
ページ17に含まれる内容の要旨
LED DENOTATION ACTIVE CARRIER RX CELL CLEAN CONNECTOR WITH ALCOHOL WIPES BEFORE CONNECTING 4OC12X/ATM-MM-SC CLASS 1 LASER PRODUCT PRODUCTO LASER DE CLASSE 1 PRODUIT LASER DE CLASSE 1 CLEAN CONNECTOR LASERPRODUKT DER KLASSE 1 WITH ALCOHOL WIPES BEFORE CONNECTING A TX INNER RX OUTER B TX INNER RX OUTER 2CHOC-12/DS3-IR-SC GIGABIT ROUTE PROCESSOR EJECT SLOT-1 SLOT-0 ACTIVE RESET CARRIER RX PKT AUX ACTIVE CARRIER CONSOLE COLL RX LINK TX RJ-45 MII O 1 2 3 Line Card Cable-Management Bracket Figure
ページ18に含まれる内容の要旨
Line Card Cable-Management Bracket The cable-management system consists of two separate components: 1. A cable-management tray that is mounted on the chassis. Refer to the appropriate Cisco 12000 Series Router installation and configuration guide for more information on the cable-management tray. 2. A cable-management bracket that attaches to a line card. This section describes the line card cable-management bracket. Figure 11 shows the single-port line card cable-management bracket; Figu
ページ19に含まれる内容の要旨
Line Card Cable-Management Bracket Note When shipped with spare line card orders, the cable-management bracket is not attached to the line card. You must attach the cable-management bracket to the line card before you insert the line card into the router. Caution Do not use the cable-management bracket as a handle to pull out or push in the line card. The cable-management bracket is designed to hold the interface cables and may break if you use the bracket to push, pull, or carry the lin
ページ20に含まれる内容の要旨
01 2 3 CLASS 1 LASER PRODUCT LASERPRODUKT DER KLASSE 1 CLEAN CONNECTOR PRODUIT LASER DE CLASSE 1 WITH ALCOHOL WIPES BEFORE CONNECTING PRODUCTO LASER DE CLASSE 1 4OC48/SRP-SFP 01 2 3 CLASS 1 LASER PRODUCT LASERPRODUKT DER KLASSE 1 CLEAN PRODUIT LASER DE CLASSE 1 CONNECTOR WITH ALCOHOL WIPES BEFORE CONNECTING PRODUCTO LASER DE CLASSE 1 4OC48/SRP-SFP PASS THRU WRAP PASS THRU WRAP PASS THRU WRAP PASS THRU WRAP PASS THRU WRAP PASS THRU WRAP PASS THRU WRAP PASS THRU WRAP Line Card Cable-Management B
