ページ1に含まれる内容の要旨
BiPAC 7300M
802.11g MIMO ADSL2+ Router
User’s Manual
ページ2に含まれる内容の要旨
Chapter 1 ................................................................................................. 1 1.1 Introducing the BiPAC 7300M................................................ 1 1.2 Features................................................................................. 3 1.3 Applications of the BiPAC 7300M .......................................... 6 Chapter 2 ................................................................................................. 7 2.1 Important No
ページ3に含まれる内容の要旨
Chapter 1 Introduction 1.1 Introducing the BiPAC 7300M Thank you for purchasing the BiPAC 7300M 802.11g MIMO ADSL2+ Modem/Router by Billion. Your new router is an all-in-one unit that combines an ADSL modem, ADSL router and Ethernet network switch to provide everything you need to get the machines on your network connected to the Internet over an ADSL broadband connection. The BiPAC 7300M router complies with ADSL2+ standards for deployment worldwide and supports downstream rates of up
ページ4に含まれる内容の要旨
making them invisible to outside users on the Internet, so it is much more difficult for a hacker to target a machine on your network. Second, it can block and redirect certain ports to limit the services that outside users can access. To ensure that games and other Internet applications run properly, you can open specific ports for outside users to access internal services on your network. The Integrated DHCP (Dynamic Host Control Protocol) client and server services allow multiple user
ページ5に含まれる内容の要旨
1.2 Features Express Internet Access – ADSL2/2+ capable The BiPAC 7300M complies with ADSL worldwide standards. Supporting downstream rates of 8Mbps with ADSL, the router is capable of up to 12/24 Mbps with ADSL2/2+, and upstream rates of up to 1 Mbps. Users enjoy not only high-speed ADSL services but also broadband multimedia applications such as interactive gaming, video streaming and real-time audio which are easier and faster than ever. The router is compliant with Multi-Mode standar
ページ6に含まれる内容の要旨
Domain Name System Relay Domain Name System (DNS) relay provides an easy way to map a domain name with a user-friendly name such as www.billion.com with an IP address. When a local machine sets its DNS server to the router’s IP address, every DNS conversion request packet from the PC to this router is forwarded to the real DNS on the outside network. Dynamic Domain Name System (DDNS) The Dynamic DNS service allows you to alias a dynamic IP address to a static hostname. This dynamic I
ページ7に含まれる内容の要旨
This feature filters the packet based on IP addresses as well as Port numbers. Filtering packets to and from the Internet provides a higher level of security control. Static and RIP1/2 Routing An easy static routing table or RIP1/2 routing protocol supports routing capability. Simple Network Management Protocol (SNMP) SNMP allows convenient remote management of the router. Web-based GUI A web-based GUI offers easy configuration and management. User-friendly and with on-line help, it a
ページ8に含まれる内容の要旨
1.3 Applications of the BiPAC 7300M 6
ページ9に含まれる内容の要旨
Chapter 2 Product Overview 2.1 Important Notes Do not use the router in high humidity or high temperatures. Do not use the same power source for the router as other equipment. Do not open or repair the case yourself. If the router is too hot, turn off the power immediately and have it repaired at a Warning qualified service center. Avoid using this product and all accessories outdoors. Place the router on a stable surface. Only use the power adapt
ページ10に含まれる内容の要旨
2.3 The Front LEDs LED Description 1 PPP : Steady glow when there is a PPPoA / PPPoE connection. Lights when successfully connected to an ADSL DSLAM 2 ADSL: (linesync). Steady glow when connected to an Ethernet device. LAN Port 3 Glows green for 100Mbps; Orange for 10Mbps. 1-4: Blinking light when data is Transmitted / Received. Lit green when the wireless connection is established. 4 WLAN: Flashes when sending/receiving data. 5 SYS : Lights when the system is re
ページ11に含まれる内容の要旨
2.4The Rear Ports 1 4 3 2 Port Description 1 DC 12V/1A Connect the supplied power adapter to this jack. After the router is powered on, press this recessed button using the end of paper clip or other small pointed object to reset the router or to restore it to factory default settings. 1. Recovery procedures for non-working routers (e.g. after a failed firmware upgrade flash): Hold the Emergency/Failure Recovery Button on the back of the modem in. Keep this button held in and turn
ページ12に含まれる内容の要旨
The detail instruction in Emergency/Failure Recovery Button 1. Recovery procedures for non-working routers (e.g. after a failed firmware upgrade flash): Hold the Emergency/Failure Recovery Button on the back of the modem in. Keep this button held in and turn on the modem. Once the lights on the modem have stopped flashing, release the Emergency/Failure Recovery Button. The modem's emergency-reflash web interface will then be accessible via http://192.168.1.254/ where you can upload a fi
ページ13に含まれる内容の要旨
2.5 Cabling One of the most common causes of problems is bad cabling or ADSL line(s). Make sure that all connected devices are turned on. On the front of the product is a bank of LEDs. Verify that the LAN Link and ADSL line LEDs are lit. If they are not, verify that you are using the proper cables. Ensure that all other devices connected to the same telephone line as your Billion router (e.g. telephones, fax machines, analog modems) have a line filter connected between them and the wall
ページ14に含まれる内容の要旨
Chapter 3 Installation You can configure the BiPAC 7300M router through the convenient and user-friendly interface of a web browser. Most popular operating systems such as Linux, Mac and Windows 98/NT/2000/XP/Me include a web browser as a standard application. 3.1 Before Configuration PCs must have a properly installed Ethernet interface and connect to the router directly or through an external repeater hub. In addition, PCs must have TCP/IP installed and configured to obtain an IP
ページ15に含まれる内容の要旨
Configuring a PC in Windows XP 1. Go to Start / Control Panel (in Classic View). In the Control Panel, double-click on Network Connections 2. Double-click Local Area Connection. 3. In the Local Area Connection Status window, click Properties. 4. Select Internet Protocol (TCP/IP) and click Properties. 5. Select the Obtain an IP address automatically and the Obtain DNS server address automatically radio buttons. 6. Click OK to finish the configuration. 13
ページ16に含まれる内容の要旨
Configuring a PC in Windows 2000 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and Dial-up Connections. 2. Double-click Local Area Connection. 3. In the Local Area Connection Status window click Properties. 4. Select Internet Protocol (TCP/IP) and click Properties. 5. Select the Obtain an IP address automatically and the Obtain DNS server address automatically radio buttons. 6. Click OK to finish the configuration. 14
ページ17に含まれる内容の要旨
Configuring PC in Windows 98/Me 1.Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Configuration tab. 2.Select TCP/IP ->NE2000 Compatible, or the name of your Network Interface Card (NIC) in your PC. 3.Select the Obtain an IP address automatically radio button. 4.Then select the DNS Configuration tab. 5.Select the Disable DNS radio button and click OK to finish the configuration. 15
ページ18に含まれる内容の要旨
Configuring PC in Windows NT4.0 1.Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Protocols tab. 2.Select TCP/IP Protocol and click Properties. 3.Select the Obtain an IP address from a DHCP server radio button and click OK. 16
ページ19に含まれる内容の要旨
3.2 Factory Default Settings Before configuring the BiPAC 7300M router, you need to know the following default settings. Web Interface: Username: admin Password: admin LAN Device IP Settings: IP Address: 192.168.1.254 Subnet Mask: 255.255.255.0 ISP setting in WAN site: PPPoE DHCP Server: DHCP server is enabled. Start IP Address: 192.168.1.100 IP pool counts: 100 3.2.1 Username and Password The default username and password are “admin” and “admin” respectively.
ページ20に含まれる内容の要旨
3.3 LAN and WAN Port Addresses The parameters of LAN and WAN ports are preset at the factory. The default values are shown below. LAN Port WAN Port IP address 192.168.1.254 The PPPoE function is enabled to Subnet Mask 255.255.255.0 automatically get the WAN port DHCP server function Enabled configuration from the IP addresses for 100 IP addresses continuing from ISP, but you have to distribution to PCs 192.168.1.100 through set the username and 192.168.1.199 password first.
