ページ1に含まれる内容の要旨
LWE100A LWE100A-W1
LWE100A-KIT LWE100A-W2
LWE100AE LWE100A-KIT-W1
LWE100AE-KIT LWE100A-KIT-W2
Wireless P-T-P Ethernet Extender User Manual
Extend Ethernet links between buildings wirelessly
®
BL A CK BOX
and with ease.
Provides affordable point-to-point wireless Ethernet extension up to
6.2 miles (10 km).
Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500)
Customer
FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-074
ページ2に含まれる内容の要旨
Trademarks Used in this Manual Trademarks Used in this Manual Black Box and the Double Diamond logo are registered trademarks of BB Technologies, Inc. Google Chrome is a registered trademark of Google Inc. Microsoft and Internet Explorer are registered trademarks of Microsoft Corporation. Firefox is a registered trademark of Mozilla Foundation. Netscape is a registered trademark of Netscape Communications Corporation. Any other trademarks mentioned in this manual are acknowledged to be the prope
ページ3に含まれる内容の要旨
FCC and IC RFI Statements FEDERAL COMMUNICATIONS COMMISSION and INDUSTRY CANADA RADIO FREQUENCY INTERFERENCE STATEMENTS Class B Digital Device. This equipment has been tested and found to comply with the limits for a Class B computing device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation.
ページ4に含まれる内容の要旨
NOM Statement Instrucciones de Seguridad (Normas Oficiales Mexicanas Electrical Safety Statement) 1. Todas las instrucciones de seguridad y operación deberán ser leídas antes de que el aparato eléctrico sea operado. 2. Las instrucciones de seguridad y operación deberán ser guardadas para referencia futura. 3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de operación deben ser respetadas. 4. T odas las instrucciones de operación y uso deben ser seguidas. 5. El aparato
ページ5に含まれる内容の要旨
Table of Contents Table of Contents 1. Specifications .........................................................................................................................................................................7 1.1 General ..........................................................................................................................................................................7 1.2 Radio ............................................................................
ページ6に含まれる内容の要旨
Table of Contents 6.8 Password .....................................................................................................................................................................44 6.9 Certificate Settings ......................................................................................................................................................45 7. Monitoring Tools .................................................................................................
ページ7に含まれる内容の要旨
Chapter 1: Specifications 1. Specifications 1.1 General Standards — IEEE 802.3u MDI/MDI-X 10/100 Fast Ethernet, IEEE 80.11b/g wireless LAN interface, IEEE 802.1n draft wireless LAN standard Temperature Tolerance — Operating: -4 to +158° F (-20 to +70° C); Storage: -22 to +176° F (-30 to +80° C) Humidity Tolerance — Operating: 10–95%; Storage: 10–95% Power — Input current: 0.5 A maximum; Output Voltage: 15 V; Output Current: 0.8 A Size — 2.4"H x 2.5"W x 8.9"D (6.1 x 6.4 x 22
ページ8に含まれる内容の要旨
Chapter 2: Overview 2. Overview 2.1 Introduction Designed for outdoor environment applications, the Wireless P-T-P Ethernet Extender is a high-performance last-mile broadband solution that provides reliable wireless network coverage. As an IEEE 802.11b/g compliant wireless device, the Wireless P-T-P Ethernet Extender is able to provide stable and efficient wireless performance. The extender delivers a much faster data rate than normal wireless devices and higher bandwidth with longer range fo
ページ9に含まれる内容の要旨
Chapter 2: Overview 1 2 2 2 Figure 2-1. LWE100A Ethernet extender. 3 Figure 2-2. Pole-mounting ring. 4 5 6 Figure 2-3. Power cord and PoE injector. 724-746-5500 | blackbox.com 724-746-5500 | blackbox.com Page 9
ページ10に含まれる内容の要旨
Chapter 2: Overview Table 2-1. Components. Number Component Description 1 (1) reverse N-type connector Ground the connector first, then install the antenna here. 2 (3) pole mounts You will install the pole mounting ring through these mounts. 3 (1) pole mounting ring Secures the extender to the pole 4 (1) U.S. power plug Connects to a power source 5 (1) 2.5-mm barrel connector Connects to the PoE injector 6 (1) Power over Ethernet (PoE) injector Supplies power to the extender WARNING: U sers MUST
ページ11に含まれる内容の要旨
Chapter 3: Hardware Installation 3. Hardware Installation This chapter describes safety precautions and product information you have to know and check before installing the Wireless P-T-P Ethernet Extender. 3.1 Preparing for Installation Read this chapter before installing the extender. It describes safety precautions and needed product information. 3.2 Professional Installation Required Use a professional installer who is well trained in the RF installation and knowledgeable about local regula
ページ12に含まれる内容の要旨
Chapter 3: Hardware Installation Figure 3-1. Removing the bottom cover. 2. Plug a standard Ethernet cable into the RJ-45 port. See Figure 3-2. Figure 3-2. Plugging in the cable. 3. Slide the cover back to seal the bottom of the Wireless P-T-P Ethernet Extender. Page 12 724-746-5500 | blackbox.com 724-746-5500 | blackbox.com
ページ13に含まれる内容の要旨
Chapter 3: Hardware Installation Figure 3-3. Replacing the cover. 4. T ake out the power cord and PoE injector, and plug the power cord into the DC port of the PoE injector as the right-side picture in Figure 3-4 shows. Figure 3-4. Installing the power cord and PoE injector. 5. Put what you assembled in step 3 and step 4 together by plugging the other side of the Ethernet cable from step 3 into the PoE port of the PoE injector shown in step 4. When you finish step 5, the extender, power cord,
ページ14に含まれる内容の要旨
Chapter 3: Hardware Installation Figure 3-5. Extender. 3.5.2 Pole Mounting 1. Turn the Wireless P-T-P Ethernet Extender over. Put the pole mounting ring through the middle hole of the Wireless P-T-P Ethernet Extender. NOTE: Use a screwdriver to unlock the pole-mounting ring before putting it through the Wireless P-T-P Ethernet Extender as the right-side picture in Figure 3-6 shows. Page 14 724-746-5500 | blackbox.com 724-746-5500 | blackbox.com
ページ15に含まれる内容の要旨
Chapter 3: Hardware Installation Figure 3-6. Unlocking the pole-mounting ring. 2. Mount the Wireless P-T-P Ethernet Extender firmly to the pole by locking the pole mounting ring tightly. Figure 3-7. Mounting the extender to a pole. 3. When installation is complete, the extender should look like Figure 3-8. 724-746-5500 | blackbox.com 724-746-5500 | blackbox.com Page 15
ページ16に含まれる内容の要旨
Chapter 3: Hardware Installation Figure 3-8. Extender installed outdoors on a pole. 3.5.3 Using the External Antenna If you prefer to use the external antenna with N-type connector for your application instead of the built-in directional antenna, follow the steps below. 1. G rab the black rubber on the top of the Wireless P-T-P Ethernet Extender, and slightly pull it up as shown in Figure 3-9. The metal N-type connector will appear. Page 16 724-746-5500 | blackbox.com 724-746-5500 | b
ページ17に含まれる内容の要旨
Chapter 3: Hardware Installation Figure 3-9. Installing the external antenna. 2. Connect your antenna with the N-type connector on the top of the Wireless P-T-P Ethernet Extender. NOTES: 1. Before connecting the external antenna with the N-type connector to the Wireless P-T-P Ethernet Extender, users should prepare the cable in advance, if needed. 2. While connecting the N-type connectors, users should be careful not to damage the connectors. WARNING: U sers MUST power off the Wireless P-T-P
ページ18に含まれる内容の要旨
Chapter 3: Hardware Installation 3. Connect the other end of the grounding wire to the earth ground. Figure 3-11. Connecting the other end of the grounding wire. Page 18 724-746-5500 | blackbox.com 724-746-5500 | blackbox.com
ページ19に含まれる内容の要旨
Chapter 4: Basic Settings 4. Basic Settings 4.1 Factory Default Settings To return the extender to its factory-default settings, see Section 6.6. Table 4-1. Wireless P-T-P Ethernet Extender Factory Default Settings. Parameter Default Setting Username admin Password password Wireless Device Name apXXXXXX (X represents the last 6 digits of the Ethernet MAC address) Operating Mode AP Data Rate Auto LAN IP Address 192.168.1.1 LAN Subnet Mask 255.255.255.0 LAN Gateway 0.0.0.0 LAN Primary DNS Server
ページ20に含まれる内容の要旨
Chapter 4: Basic Settings 4.2 System Requirements Before configuration, make sure your system meets the following requirements: • You will need a computer coupled with a 10/100 BASE-TX adapter; • Configure the computer with a static IP address of 192.168.1.x. NOTE: The default IP address of Wireless P-T-P Ethernet Extender is 192.168.1.1. (X cannot be 0, 1, nor 255); ® ® ® ® • A Web browser on a PC for configuration such as Microsoft Internet Explorer 6.0 or above, Netscape , Firefox , or Googl
