ページ1に含まれる内容の要旨
MicroMMAC-T User's Guide
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
Notice Enterasys Networks reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult Enterasys Networks to determine whether any such changes have been made. The hardware, firmware, or software described in this manual is subject to change without notice. IN NO EVENT SHALL ENTERASYS NETWORKS BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT
ページ4に含まれる内容の要旨
AppleTalk, Apple, Macintosh, and TokenTalk are registered trademarks; and Apple Remote Access and EtherTalk are trademarks of Apple Computer, Inc. SmartBoost is a trademark of American Power Conversion ST is a registered trademark and C++ is a trademark of AT&T Banyan and VINES are registered trademarks of Banyan Systems, Inc. cisco, ciscoSystems, and AGS+ are registered trademarks; and cBus, cisco Router, CRM, IGS, and MGS are trademarks of cisco Systems, Inc. GatorBox is a registered tradema
ページ5に含まれる内容の要旨
Restricted Rights Notice (Applicable to licenses to the United States Government only.) 1. Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS 252.227-7013. Enterasys Networks, 35 Industrial Way, Rochester, New Hampshire 03867-0505. 2. (a) This computer software is submitted with restricted rights. It may not be used, reproduced, or disclosed by the Governm
ページ6に含まれる内容の要旨
iv
ページ7に含まれる内容の要旨
Contents Chapter 1 Introduction Using This Guide .......................................................................................................... 1-2 Related Manuals............................................................................................................ 1-3 Software Conventions .................................................................................................. 1-3 Using the Mouse ........................................................................
ページ8に含まれる内容の要旨
Contents Accessing the UPS Window ........................................................................ 2-25 Setting the UPS ID ........................................................................................ 2-27 Using the Test Option................................................................................... 2-27 Using the Disconnect Option ...................................................................... 2-27 Resetting the Device ........................................
ページ9に含まれる内容の要旨
Contents The Station Statistics Window Performance Fields ................................. 3-20 The Station Statistics Window Soft Error Fields ...................................... 3-21 The Station Timer Statistics Window ................................................................ 3-22 Station Timer Statistics Window Fields..................................................... 3-23 Port Performance Graphs ...................................................................................
ページ10に含まれる内容の要旨
Contents viii
ページ11に含まれる内容の要旨
Chapter 1 Introduction How to use this guide; related guides; software conventions; getting help; MicroMMAC-T firmware versions Welcome to the NetSight Element Manager for the MicroMMAC-T User’s Guide. We have designed this guide to serve as a simple reference for using NetSight Element Manager for the MicroMMAC-22T/24T and MicroMMAC-42T/44T. ™ ™ The MicroMMAC-22T/24T and MicroMMAC-42T/44T are intelligent Token Ring hubs that provide front panel ports for network connections, a rear-panel ™
ページ12に含まれる内容の要旨
Introduction NetSight Element Manager provides remote management for the MicroMMAC-T, including: • Front panel status display with administrative state, network load, and error percentages available for each port. • Management Station Configuration. • Station List and Map Windows. • Full statistics display for the hub and individual stations (with both numerical and graphical display options). • Alarm Limits based on frame counts, frame errors, or beacon frames. You should read this manual th
ページ13に含まれる内容の要旨
Introduction We assume that you have a general working knowledge of Token Ring IEEE 802.5 type data communications networks and their physical layer components. Related Manuals The MicroMMAC-T user’s guide is only part of a complete document set designed to provide comprehensive information about the features available to you through NetSight Element Manager. Other guides that include important information related to managing the MicroMMAC-T include: Enterasys’ NetSight Element Manager User’
ページ14に含まれる内容の要旨
Introduction Left Mouse Button Right Mouse Button Figure 1-1. Mouse Buttons For many mouse operations, this document assumes that the left (primary) mouse button is to be used, and references to activating a menu or button will not include instructions about which mouse button to use. However, in instances in which right (secondary) mouse button functionality is available, instructions will explicitly refer to right mouse button usage. Also, in situations where you may be switching between
ページ15に含まれる内容の要旨
Introduction Using Window Buttons The button that appears at the bottom of most windows allows you to exit a window and terminate any unsaved changes you have made. You may also have to use this button to close a window after you have made any necessary changes and set them by clicking on an , , or button. An , , or button appears in windows that have configurable values; it allows you to confirm and SET changes you have made to those values. In some windows, you may have to use this but
ページ16に含まれる内容の要旨
Introduction Device Location Name MAC Address IP Address Figure 1-2. Sample Window Showing Informational Text Boxes Device Name Displays the user-defined name of the device. The device name can be changed via the System Group window; see the Generic SNMP User’s Guide for details. IP Address Displays the device’s IP (Internet Protocol) Address; this will be the IP address used to define the device icon. IP addresses are assigned via Local Management for the MicroMMAC-T; they cannot be chang
ページ17に含まれる内容の要旨
Introduction Getting Help This section describes two different methods of getting help for questions or concerns you may have while using NetSight Element Manager. Using On-line Help You can use the MicroMMAC-T window buttons to obtain information specific to the device. When you click on a Help button, a window will appear that contains context-sensitive on-screen documentation that will assist you in the use of the windows and their associated command and menu options. Note that if a Hel
ページ18に含まれる内容の要旨
Introduction Netsight_docs@enterasys.com To locate product specific information, refer to the Enterasys Web site: http://www.enterasys.com/. For the highest firmware versions successfully tested with NetSight Element Manager NOTE 2.2.1, refer to the Readme file from the NetSight Element Manager program group. If you have an earlier version of firmware and experience problems, contact the Global Technical Assistance Center. 1-8 Getting Help
ページ19に含まれる内容の要旨
Chapter 2 The MicroMMAC-T Chassis View Information displayed in the Chassis View window; the Chassis Manager window; Hub management functions The MicroMMAC-T Chassis View window is the main screen that immediately informs you of the current configuration of your MicroMMAC-T via a graphical display of the device’s front panel. The Chassis View displays the condition of individual ports on the MicroMMAC-T. The Chassis View window serves as a single point of access to all other MicroMMAC-T win
ページ20に含まれる内容の要旨
The MicroMMAC-T Chassis View Viewing Chassis Information The MicroMMAC-T Chassis View window (Figure 2-1) provides a graphic representation of the MicroMMAC-T’s front panel, including a color-coded port display which immediately informs you of the current configuration and status of all station and ring ports on the device. The module index will change to reflect Click on the module number to which module in the stack is currently change the Chassis View to display displayed. Click here
