ページ1に含まれる内容の要旨
EM78P809N
8-BIT
Microcontroller
Product
Specification
DOC. VERSION 1.0
ELAN MCCROELECTRONICS CORP.
July 2005
ページ2に含まれる内容の要旨
Trademark Acknowledgments: IBM is a registered trademark and PS/2 is a trademark of IBM. Windows is a trademark of Microsoft Corporation. ELAN and ELAN logo are trademarks of ELAN Microelectronics Corporation. Copyright © 2005 by ELAN Microelectronics Corporation All Rights Reserved Printed in Taiwan The contents of this specification are subject to change without further notice. ELAN Microelectronics assumes no responsibility concerning the accuracy, adequacy, or complet
ページ3に含まれる内容の要旨
Contents Contents 1 General Description ··························································································· 1 2 Features ·············································································································· 1 2.1 CPU········································································································································ 1 2.2 Applications·································································
ページ4に含まれる内容の要旨
Contents 5 Absolute Maximum Ratings ············································································ 63 5.1 Absolute Maximum Ratings ································································································· 63 5.2 Recommended Operating Conditions·················································································· 63 6 Electrical Characteristics················································································· 64 6.1 DC Ele
ページ5に含まれる内容の要旨
EM78P809N 8-Bit Microcontroller 1 General Description The EM78P809N is an 8-bit microprocessor with low-power, high-speed CMOS technology and high noise immunity. It has a built-in 8K×13-bits Electrical One Time Programmable Read Only Memory (OTP-ROM). It provides multi-protection bits to prevent intrusion of user’s OTP memory codes. Seven Option bits are also available to meet user’s requirements. With its OTP-ROM feature, the EM78P809N is able to offer a convenient way of develop
ページ6に含まれる内容の要旨
EM78P809N 8-Bit Microcontroller 16 bits Counter/Timer TC2: Timer/Counter/Window 8 bits Timer/Counter TCC: 8-bit real time clock/counter with overflow interrupt TC3: Timer/Counter/Capture TC4: Timer/Counter/ PWM (pulse width modulation)/PDO (Programmable divider output) Time Base Timer: (1Hz ~16kHz at 8MHz) Key tone output: (1kHz ~ 8kHz at 8MHz) Serial transmitter/receiver interface Serial Peripheral Interface (SPI): Three-wire synchronous communication Universal asynchr
ページ7に含まれる内容の要旨
EM78P809N 8-Bit Microcontroller 3 Pin Assignment (ACLK) OSCO 1 28 VDD 2 27 OSCI /RESET (VPP) 3 26 TEST P67 (DINCK) (AD0) P90 4 25 P66 (DATAIN) 5 24 (AD1) P91 P65 (PGMB) 6 23 (AD2) P92 P64 (/SS)(OEB) (AD3) P93 7 22 P63 (/TONE) 8 21 (AD4) P94 P62 (TC2) 9 20 (AD5) P95 P61 (INT1) (AD6) P96 10 19 P60 (/INT0) 11 18 (AD7/VREF) P97 P73 (/SLEEP, /INT5) 12 17 (TC3, INT3) P80 P72 (TX,SO) 13 16 (TC4, /PWM, /PDO) P81 P71(RX,SI) 14 15 VSS P70 (/SCK) EM78P809N Fig. 1. Pin Assignment 4 Pin Description
ページ8に含まれる内容の要旨
EM78P809N 8-Bit Microcontroller Symbol Pin No. Type Function * P80~P83 are bi-directional I/O pins * P80 can be used as 8-bit Timer/Counter 3 (TC3) or external Interrupt Input 3 (INT3) P80~P81 12~13 I/O * P81 can be used as 8-bit Timer/Counter 4 (TC4) or programmable divider output (PDO) * P80 ~ P81 can be used as pull high or pull low pins * P90~P97 are bi-directional I/O pins P90~P97 4~11 I/O * P90~P97 can be used as 8 channel 10-bit resolution A/D converter * P97 can be used a
ページ9に含まれる内容の要旨
EM78P809N 8-Bit Microcontroller 4 Function Description 4.1 Functional Block Diagram OSCI OSCO WDT timer Stack ROM WDT Prescaler R2 Oscillator Timing Control TCC Prescaler R1 (TCC) ALU Interrupt Instruction Control Register General RAM R3 ACC R5 Control Sleep and Wake-up I/O Port Instruction R4 Decoder DATA and CONTROL BUS PORT6 PORT7 PORT8 PORT9 TC 2 (16-bit Timer/Counter) TC 3 (8-bit Timer/Counter, Capture Mode) TC 4 (8-bit Timer/Counter, PWM, PDO) IOC6 R6 IOC7 R7 IOC8 R8 IOC9 R9 SPI (
ページ10に含まれる内容の要旨
EM78P809N 8-Bit Microcontroller 4.2 Operating Registers REGISTER REGISTER REGISTER REGISTER CONTROL BANK 0 BANK 1 BANK 2 BANK 3 REGISTER Address 00 R0/ IAR 01 R1/ TCC 02 R2/ PC 03 R3/ SR R3 (7,6)= (0,1) R3 (7,6)= (1,0) R3 (7,6)= (1,1) R4/ RSR 04 SCR TC3CR URC1 SPIC1 Reserved 05 PORT6 TC3DA URC2 SPIC2 IOC6 06 PORT7 TC3DB URS SPID IOC7 07 PORT8 TC2CR/ ADDL URRD Reserved IOC8 08 09 PORT9 TC2DH URTD Reserved IOC9 0A Reserved TC2DL Reserved PHC1 Reserved 0B TC4CR ADCR Reserved PLC1 INTCR 0C TC4D
ページ11に含まれる内容の要旨
EM78P809N 8-Bit Microcontroller R0/IAR − Indirect Addressing Register ( Address: 00h ) R0 is not a physically implemented register. Its major function is to act as an indirect addressing pointer. Any instruction using R0 as a pointer actually accesses data pointed by the RAM Select Register (R4). R1/TCC − Time Clock /Counter ( Address: 01h ) This register is writable and readable just like the other registers. The contents of the prescaler counter are cleared only when a value is
ページ12に含まれる内容の要旨
User Memory Space EM78P809N 8-Bit Microcontroller R5 PC A12 A11 A10 A9 A8 A7 ~ A0 0000h Reset Vector CALL 000 : PAGE0 0000~03FF 0003h RET WDT Timer Overflow RETL Store ACC, R3, R5 0006h 001 : PAGE1 0400~07FF RETI External INT0 Pin Interrupt Occurs 010 : PAGE2 0800~0BFF STACK LEVEL 1 0009h TCC Overflow STACK LEVEL 2 000Fh 011 : PAGE3 0C00~0FFF External INT1 pin Interrupt Occurs STACK LEVEL 3 100 : PAGE4 1000~13FF STACK LEVEL 4 0012h Time Base Timer Interrupt STACK LEVEL 5 0015h 10
ページ13に含まれる内容の要旨
EM78P809N 8-Bit Microcontroller Bit 3 (P) : Power down bit. Set to “1” during power on or by a "WDTC" command and reset to “0” by a "SLEP" command. Bit 2 (Z) : Zero flag. Set to "1" if the result of an arithmetic or logic operation is zero. Bit 1 (DC) : Auxiliary carry flag Bit 0 (C) : Carry flag R4/RSR − RAM Select Register ( Address: 04h ) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 GRBS1 RBS0 RSR5 RSR4 RSR3 RSR2 RSR1 RSR0 Bit 7: 6 ( GRBS1 : GRBS0 ) : determine which gener
ページ14に含まれる内容の要旨
EM78P809N 8-Bit Microcontroller PS2 PS1 PS0 Program Memory Page [Address] 0 0 0 Page 0 [0000~03FF] 0 0 1 Page 1 [0400~07FF] 0 1 0 Page 2 [0800~0BFF] 0 1 1 Page 3 [0C00~0FFF] 1 0 0 Page 4 [1000~13FF] 1 0 1 Page 5 [1400~17FF] 1 1 0 Page 6 [1800~1BFF] 1 1 1 Page 7 [1C00~1FFF] Bit 1 ( SIS ) : SLEEP and IDLE mode select. SIS = “0” : IDLE mode SIS = “1” : SLEEP mode Bit 0 ( REM ) : Release method for sleep mode. REM = “0” : /SLEEP pin input rising edge release REM = “1” : /SLE
ページ15に含まれる内容の要旨
EM78P809N 8-Bit Microcontroller PORT9 − Port 9 I/O Data Register ( Address: 09h ) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 P97 P96 P95 P94 P93 P92 P91 P90 Bit 7 ~ Bit 0 ( P97 ~ P90 ) : 8-bit Port 97 ~ Port 90 I/O data register User can use IOC9 register to define each bit whether input or output. TC4CR — Timer/Counter 4 Control Register ( Address: 0Bh ) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 TC4FF1 TC4FF0 TC4S TC4CK2 TC4CK1 TC4CK0 TC4M1 TC4M0 Bit 7 ~ Bit 6 ( TC4FF1
ページ16に含まれる内容の要旨
EM78P809N 8-Bit Microcontroller TC4D − Timer 4 Data Buffer ( Address: 0Ch ) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 TC4D7 TC4D6 TC4D5 TC4D4 TC4D3 TC4D2 TC4D1 TC4D0 Bit 7 ~ Bit 0 ( TC4D7 ~ TC4D0 ) : Data buffer of 8-bit Timer/Counter 4. ISFR0 − Interrupt Status Flag Register 0 and INT3 Edge Detect Flag. ( Address : 0Dh ) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 0 INT3F INT3R 0 0 WDTIF EXIF0 Bit 5 ( INT3F ) : External interrupt 3 falling edge detect flag. INT3F = “
ページ17に含まれる内容の要旨
EM78P809N 8-Bit Microcontroller ISFR2 − Interrupt Status Flag Register 2 ( Address: 0Fh ) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 UERRIF RBFF TBEF TBIF EXIF1 0 TCIF0 Bit 6 (UERRIF) : UART Receiving Error Interrupt, cleared by software or UART disabled. Bit 5 (RBFF) : UART Receive Mode Data Buffer Full Interrupt Flag. Flag cleared by software. Bit 4 (TBEF) : UART Transmit Mode Data Buffer Empty Interrupt Flag. Flag cleared by software. Bit 3 (TBIF) : Time Base Timer Inte
ページ18に含まれる内容の要旨
EM78P809N 8-Bit Microcontroller Bit 5 ~ Bit 4 ( TC3CK1 ~ TC3CK0 ) : Timer/Counter3 Clock Source Select Clock source Resolution Max. time TC3CK1 TC3CK0 ( Normal, Idle ) ( Fc=8M ) ( Fc=8M ) 12 0 0 Fc/2 512 μS 131.1mS 10 0 1 Fc/2 128 μS 32.6mS 7 1 0 Fc/2 16 μS 4.1mS 1 1 External clock (TC3 pin) - - Bit 3 ( TC3M ) : Timer/Counter 3 mode select TC3M = “0” : Timer/Counter3 mode TC3M = “1” : Capture mode TC3DA − Timer 3 Data Buffer A ( Address: 06h ) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit
ページ19に含まれる内容の要旨
EM78P809N 8-Bit Microcontroller Bit 2 ~ Bit 0 ( TC2CK2 ~ TC2CK0 ) : Timer/Counter 2 Clock Source Select Clock Source Resolution Max. Time TC2CK2 TC2CK1 TC2CK0 ( Normal, Idle ) ( Fc=8M ) ( Fc=8M ) 23 0 0 0 Fc/2 1.05s 19.1h 13 0 0 1 Fc/2 1.02ms 1.1min 8 0 1 0 Fc/2 32 μs 2.1s 3 0 1 1 Fc/2 1 μs 65.5ms 1 0 0 Fc 125ns 7.9ms 1 0 1 - - - 1 1 0 - - - 1 1 1 External clock (TC2 pin) TC2DH − Timer 2 Data Buffer High Byte ( Address: 09h ) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 T
ページ20に含まれる内容の要旨
EM78P809N 8-Bit Microcontroller Bit 5~ Bit 4 ( ADCK1 ~ ADCK0 ) : AD Conversion Time Select Clock Source Max. Operating ADCK1 ADCK0 ( Normal, Idle ) Frequency (Fc) 0 0 Fc/4 1MHz 0 1 Fc/16 4MHz 1 0 Fc/32 8MHz 1 1 Reserved - Bit 3 ( ADP ) : AD power control ADP = “0” : Power on ADP = “1” : Power down Bit 2 ~ Bit 0 ( ADIS2 ~ ADIS0 ) : Analog Input Pin Select ADIS2 ADIS1 ADIS0 Analog Input Pin 0 0 0 AD0 0 0 1 AD1 0 1 0 AD2 0 1 1 AD3 1 0 0 AD4 1 0 1 AD5 1 1 0 AD6 1 1 1 AD7
