ページ1に含まれる内容の要旨
TL-PA4020P
AV500 2-port Powerline Adapter with AC Pass Through
REV1.0.0
1910010946
ページ2に含まれる内容の要旨
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2013 TP-LINK TECHNOLOGIES CO.,
ページ3に含まれる内容の要旨
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarante
ページ4に含まれる内容の要旨
TP-LINK TECHNOLOGIES CO., LTD Safety Information • When product has power button, the power button is one of the way to shut off the product; when there is no power button, the only way to completely shut off power is to disconnect the product or the power adapter from the power source. • Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock and voiding the limited warranty. If you need service, please contact us. • Avoid water and wet locations. Th
ページ5に含まれる内容の要旨
TP-LINK TECHNOLOGIES CO., LTD DECLARATION OF CONFORMITY For the following equipment: Product Description: AV500 2-port Powerline Adapter with AC Pass Through Model No.: TL-PA4020P Trademark: TP-LINK We declare under our own responsibility that the above products satisfy all the technical regulations applicable to the product within the scope of Council Directives: Directives 2004 / 108 / EC, Directives 2006 / 95 / EC, Directives 2011/65/EU The above product is in conformity with the
ページ6に含まれる内容の要旨
CONTENTS Package Contents......................................................................................... 1 Conventions .................................................................................................. 1 Chapter 1 Introduction ................................................................................. 2 1.1 System Requirement.......................................................................... 2 1.2 Important Safety Instructions .......................
ページ7に含まれる内容の要旨
TL-PA4020P AV500 2-port Powerline Adapter with AC Pass Through Package Contents The AV500 2-port Powerline Adapter with AC Pass Through package contains the following items: One AV500 2-port Powerline Adapter with AC Pass Through (There are two powerline adapters in Starter Kit) One RJ45 Cable (There are two RJ45 Cables in Starter Kit) One Quick Installation Guide One Resource CD (Management Utility and User Guide) Note: Make sure that the package contains the above items. If
ページ8に含まれる内容の要旨
TL-PA4020P AV500 2-port Powerline Adapter with AC Pass Through Chapter 1 Introduction This device is an AV500 2-port Powerline Adapter with AC Pass Through which transforms your house’s existing electrical wiring into a ubiquitous networking infrastructure. Simply plug this AV500 2-port Powerline Adapter with AC Pass Through into an ordinary AC power outlet which will easily extend your Cable/xDSL broadband connection or existing Ethernet (LAN) network to any other electrical outlet in
ページ9に含まれる内容の要旨
TL-PA4020P AV500 2-port Powerline Adapter with AC Pass Through 8. Plug this product directly into a wall socket (100V–240V~, 50/60Hz). Do not use an extension cord between this product and the AC power source. 9. When plugging this product into a wall socket, make sure that the electrical socket is not damaged, and that there is no gas leakage. 10. Place the connecting cables properly so that people won’t stumble or walk on it. 11. This product should be operated from the type of power i
ページ10に含まれる内容の要旨
TL-PA4020P AV500 2-port Powerline Adapter with AC Pass Through At least one Ethernet port is connected, but there is no Solid data being transferred. Ethernet LED Blinking At least one Ethernet port is transferring data. Off No Ethernet port is connected. Note: 5 minutes after the device connected to the adapter is turned off, and the adapter will automatically switch to the power-saving Mode. In power-saving mode, the Homeplug cannot be accessed via the electrical wiring, but its
ページ11に含まれる内容の要旨
TL-PA4020P AV500 2-port Powerline Adapter with AC Pass Through Note: 1. If the pair button is pressed till all the LEDs turn off (at least 7 seconds), the powerline adapter will leave the network which it has joined and its new network name assumes a random value. The Power LED turns off temporarily when it disconnects from the powerline network. 2. For detailed information about the pair button, please refer to Chapter 5 Advanced Feature: How to Use the Pair Buttons. 5
ページ12に含まれる内容の要旨
TL-PA4020P AV500 2-port Powerline Adapter with AC Pass Through Chapter 2 Connecting Mechanism 2.1 Introduction The Powerline Adapter supports up to 500Mbps data rate. With this high speed connection rate, this Powerline Adapter allows you to set up a high speed home network by using your home existing electrical wiring. Simply plug this Powerline Adapter into an ordinary power outlet to extend your Cable/xDSL broadband connection or existing LAN network to any other electrical outlet in
ページ13に含まれる内容の要旨
TL-PA4020P AV500 2-port Powerline Adapter with AC Pass Through 2.3 Hardware Connection – Computer For those computers you wish to be networked by Powerline Adapter, each of the computers must be properly connected with a Powerline Adapter through an Ethernet (RJ45) cable. Following are the steps to properly connect the Powerline Adapter to your computer: 1 ． Connect one end of the provided Ethernet (RJ45) cable to the Powerline Adapter’s Ethernet port. 2 ． Connect the other end of the
ページ14に含まれる内容の要旨
TL-PA4020P AV500 2-port Powerline Adapter with AC Pass Through 2.4 Hardware Connection – Internet This section describes how to connect the Powerline Adapter into your existing ADSL broadband connection via ADSL Ethernet port. Follow the procedures described below to connect the Powerline Adapter to your ADSL broadband connection: 1 ． Connect one end of the provided Ethernet (RJ45) cable to the Powerline Adapter’s Ethernet port. 2 ． Connect the other end of the Ethernet (RJ45) cable to a
ページ15に含まれる内容の要旨
TL-PA4020P AV500 2-port Powerline Adapter with AC Pass Through Chapter 3 Installing Management Utility Please verify that no other Powerline Adapter or any Encryption Management Utilities are installed before installing the provided software. If other Powerline Utilities are installed, uninstall them and restart your personal computer before installing this provided software. Note: To install Management Utility, please make sure that WinPcap 4.1.2 has been installed in your computer
ページ16に含まれる内容の要旨
TL-PA4020P AV500 2-port Powerline Adapter with AC Pass Through 10
ページ17に含まれる内容の要旨
TL-PA4020P AV500 2-port Powerline Adapter with AC Pass Through 11
ページ18に含まれる内容の要旨
TL-PA4020P AV500 2-port Powerline Adapter with AC Pass Through Step 3: After the installation, a shortcut to the “Powerline Utility” application icon is provided on the windows desktop. 12
ページ19に含まれる内容の要旨
TL-PA4020P AV500 2-port Powerline Adapter with AC Pass Through Chapter 4 Using the Management Utility After you’d successfully installed the Powerline Adapter hardware and Management Utility software, you can set up or configure the devices according to your need. This Powerline Utility enables the users to identify powerline devices on the powerline network, measures data rate performance and ensures privacy by setting user defined secure powerline networks. Double click on the icon
ページ20に含まれる内容の要旨
TL-PA4020P AV500 2-port Powerline Adapter with AC Pass Through MAC Address: Displays the MAC address of the powerline adapter connected to the current computer where this management utility is running. Network Name: Displays the network name of the current network or you can give a name for the network in which the powerline adapter is. By default, the network name is HomeplugAV. Use Default (HomePlugAV): Check the box before this item to use the default network name. Apply: Click
