ページ1に含まれる内容の要旨
USB Mobile Port Replicator
with Ethernet
NOTEBOOK COMPUTER
MOBILE PORT REPLICATOR
User’s Guide
ページ2に含まれる内容の要旨
INTRODUCTION Congratulations on your purchase of the Targus USB Mobile Port Replicator with Ethernet! It is an intelligent expansion module that easily connects to a PC or notebook via a USB port. This user’s guide describes the port replicator’s features, and gives instructions for connecting various devices and installing the software. System Requirements v USB V.1.1 compliant port v Operating system: Windows 98 or Windows 2000 Contents In addition to this user’s guide, the package contains: v
ページ3に含まれる内容の要旨
Figure 1. USB Mobile Port Replicator Ports Figure 2. End of the USB Mobile Port Replicator Figure 3. USB Cable Coiled in the Cable Compartment Figure 4. USB Mobile Port Replicator LED Lights 2
ページ4に含まれる内容の要旨
Open the USB cable compartment (Figure 3), uncoil the cable, and plug the USB connector into the USB port of your computer. LED Status Indicators Once you connect the port replicator to the computer and turn on the computer, the LED lights display as follows: v The Hub Link and both USBs glow green. v The serial (RS232) and parallel ports glow green when devices are attached. v The PS/2 port lights flash green when a device is first connected or there is activity on the ports. v The Tx/Rx light
ページ5に含まれる内容の要旨
Installing USB Hub Support The New Hardware Detected message box appears when your computer finds the Generic Root Hub device. Then the Add New Hardware Wizard window appears. 1 Click Next . 2 When the message, What would you like Windows to do? appears, select Search for the best driver for your device, and click Next. 3 Insert the Targus driver diskette. 4 Click Next . The system locates the correct software driver. 5 Click Next to install the driver. 6 When the installation complete message a
ページ6に含まれる内容の要旨
After rebooting, any device driver that requires installation is automatically detected and the Add New Hardware Wizard window appears to complete the installation process. Installing the Serial Port Driver The New Hardware Detected message box appears, when your computer finds the PA090 Serial Converter. Then the Add New Hardware Wizard window appears. 1 Click Next . 2 When the message, What would you like Windows to do? appears, select Search for the best driver for your device, and click Nex
ページ7に含まれる内容の要旨
Installing the PS/2 Port Drivers Each PS/2 port installs a seperate port driver. The following steps repeat until all PS/2 ports are configured. The New Hardware Detected message box appears when your computer finds the USB-PS/2 Converter. Then the Add New Hardware Wizard window appears and installs the supporting driver as a USB Human Interface Device. 1 When the message, What would you like Windows to do? appears, select Search for the best driver for your device, and click Next. The system l
ページ8に含まれる内容の要旨
CONNECTING DEVICES TO THE PORT REPLICATOR When connecting a new device to any port on the port replicator, the corresponding software drivers must be installed. Consider the following guidelines when preparing to connect new devices: If your operating system is Windows 98, you will be prompted by a series of screens beginning with Add New Hardware Wizard. You may need your Windows 98 CD to complete the installation of the neccessary device driver. If your operating system is Windows 2000, th
ページ9に含まれる内容の要旨
Installing a Parallel Printer - First-Time Installation Follow the installation instructions that come with your printer. When prompted to select a port, choose PB1284-1 (USB port). If this port does not appear in the list, choose the LPT1 port, complete the manufacturer’s setup for your printer, and follow the instructions below for Printer Reconfiguration. Printer Reconfiguration Follow these instructions only if you are reconfiguring your printer from the LPT1 port to the port replicator’s pa
ページ10に含まれる内容の要旨
Using the Reset Button The Reset button is used in conjunction with the serial port on the port replicator. Whenever changing the serial devices connected to the serial port, press and hold the Reset button until the Hub Link LED light blinks so that the new device will be detected. Every time your notebook computer is powered on, press and hold the Reset button until the Hub Link LED light blinks (about 5 seconds). PRODUCT LIMITATIONS Your port replicator is splitting a single connection among
ページ11に含まれる内容の要旨
TROUBLESHOOTING Perform these self-tests before calling technical support. Device not Recognized 1 If a device attached to the port replicator is not recognized, press and hold the Reset button until the lights flash. Verify that the device is now recognized. If not, proceed to step 2. 2 Detach all cables from the port replicator, including the network cable. Plug in the AC adapter. Connect the power cable to the power input jack. Plug in each device, one at a time. Verify that each device is re
ページ12に含まれる内容の要旨
Figure 5. Serial on USB [COM2] Within that same window, you will have a PA090 Parallel Interface device. Look under Universal Serial Bus controllers to see the other devices now installed for the port replicator. Verifying Network Connection Click to expand the Network Adapters and PA090 Ethernet appears. 11
ページ13に含まれる内容の要旨
Modem Connection Figure 6. Serial Interface Controller 1 When attaching a modem to the serial (RS232) port, verify that the port assigned to your modem is Serial USB (COMx), where x is the number of the COM port. 2 If Windows does not autodetect your modem on Serial USB (COMx), rerun the Hardware Wizard. 3 Choose Select from a list instead of autodetect, then select Serial USB (COMx) as the COM port. 12
ページ14に含まれる内容の要旨
Printer The parallel port is designed to support parallel printers. Data storage devices must be connected directly to the parallel port on your notebook computer. 1 If your printer is not recognized, click Start , select Settings, then select Printers. 2 Highlight your printer, right-click the mouse button, and select Properties. 3 If the assigned port is LPT1, change it to PB1284-1 (USB port). For a first-time printer installation: 1 Select the port PB1284-1 (USB port). If this port does not
ページ15に含まれる内容の要旨
TECHNICAL SUPPORT In the unlikely event that you encounter problems with your Targus USB Mobile Port Replicator with Ethernet, contact our technical support team at: E-mail: TechSupport@targus.com Web site: www.targus.com Our knowledgeable staff is available to answer your technical questions Monday through Friday, 8:00 A.M. until 8:00 P.M. Eastern time. Telephone: 800-283-6325 (Toll Free) WARRANTY Targus warrants this product to be free from defects in material and workmanship for one year. If
ページ16に含まれる内容の要旨
The Leading Global Supplier of Portable Solutions Visit our Web site at www.targus.com NEW YORK • LOS ANGELES • TORONTO • TOKYO • HONG KONG SINGAPORE • SYDNEY • LONDON • PARIS • BRUSSELS • HANNOVER MILANO • BARCELONA • AMSTERDAM Features and specifications are subject to change without notice. ©2000 Targus Corp. 400-0015-001A
