ページ1に含まれる内容の要旨
USB97C242
USB 2.0 Flash Drive
Controller
Datasheet
Product Features
2.5 Volt, Low Power Core Operation Double Buffered Bulk Endpoint
− Bi-directional 512 Byte Buffer for Bulk Endpoint
3.3 Volt I/O with 5V input tolerance
− 64 Byte RX Control Endpoint Buffer
Complete USB Specification 2.0 Compatibility
− 64 Byte TX Control Endpoint Buffer
− Includes USB 2.0 Transceiver
Internal or External Program Memory Interface
− A Bi-directional Control and a Bi-directional Bulk
En
ページ2に含まれる内容の要旨
USB 2.0 Flash Drive Controller Datasheet 80 ARKAY DRIVE, HAUPPAUGE, NY 11788 (631) 435-6000, FAX (631) 273-3123 Copyright © 2007 SMSC or its subsidiaries. All rights reserved. Circuit diagrams and other information relating to SMSC products are included as a means of illustrating typical applications. Consequently, complete information sufficient for construction purposes is not necessarily given. Although the information has been
ページ3に含まれる内容の要旨
USB 2.0 Flash Drive Controller Datasheet USB97C242 Revision History PAGE(S) SECTION/FIGURE/ENTRY CORRECTION DATE REVISED 1 Cover Added lead-free ordering information Rev. 1.4 02-16-06 5 Chapter 1 – General Description First bullet modified under the Rev. 1.3 following section: 07-08-04 Internal program code provides the following features: Support for 1 to 8, 128Mb through 2Gb, 512byte and 2048 byte page size, 8bit parallel NAND flash memories, including multiple memory aggreg
ページ4に含まれる内容の要旨
USB 2.0 Flash Drive Controller Datasheet TABLE OF CONTENTS REVISION HISTORY .....................................................................................................................................................2 CHAPTER 1 GENERAL DESCRIPTION ...................................................................................................................5 CHAPTER 2 ACRONYMS & DEFINITION .............................................................................
ページ5に含まれる内容の要旨
USB 2.0 Flash Drive Controller Datasheet Chapter 1 General Description The USB97C242 is a USB2.0 Bulk Only Mass Storage Class Peripheral Controller intended for supporting SmartMedia (SM), and NAND flash memory devices. It provides a single chip USB reader solution for the SM and NAND flash devices in the market*. The device consists of a USB 2.0 PHY and SIE, buffers, Fast 8051 microprocessor with expanded scratchpad, and program SRAM, 48KB program ROM and SM controller. Provisions fo
ページ6に含まれる内容の要旨
USB 2.0 Flash Drive Controller Datasheet Note: * In order to develop, make, use, or sell readers and/or other products using or incorporating any of the SMSC devices made the subject of this document or to use related SMSC software programs, technical information and licenses under patent and other intellectual property rights from or through various persons or entities, including without limitation media standard companies, forums, and associations, and other patent holders ma
ページ7に含まれる内容の要旨
USB 2.0 Flash Drive Controller Datasheet Chapter 2 Acronyms & Definition 2.1 Acronyms SM: SmartMedia SMC: SmartMedia Controller FM: Flash Media FMC: Flash Media Controller ECC: Error Checking and Correcting CRC: Cyclic Redundancy Checking SMSC USB97C242 Page 7 Revision 1.4 (05-03-07) DATASHEET
ページ8に含まれる内容の要旨
USB 2.0 Flash Drive Controller Datasheet Chapter 3 Pin Tables Table 3.1 – USB97C242 100 Pin Package NAND FLASH/SMARTMEDIA INTERFACE (17 PINS) D0 D1 D2 D3 D4 D5 D6 D7 ALE CLE nRE nWE nWP nB/R nCE nCD nWPS USB INTERFACE (7 PINS) USB+ USB- LOOPFLTR RBIAS RTERM FS+ FS- MEMORY/IO INTERFACE (29 PINS) MA0 MA1 MA2 MA3 MA4 MA5 MA6 MA7 MA8 MA9 MA10 MA11 MA12 MA13 MA14 MA15 MD0 MD1 MD2 MD3 MD4 MD5 MD6 MD7 nMRD nMWR nMCE nIOW nIOR MISC (21 PINS) ROMEN GPIO1 GPIO20 GPI
ページ9に含まれる内容の要旨
USB 2.0 Flash Drive Controller Datasheet PIN # NAME MA PIN # NAME MA PIN # NAME MA PIN # NAME MA 9 MA8 8 34 nIOR 8 59 nCS1 84 XTAL1/CL KIN 10 MA9 8 35 ROMEN 60 VSSCORE 85 XTAL2 11 MA10 8 36 D0 12 61 nCS2 86 VSSP 12 VDDCOR 37 D1 62 VDDIO 87 LOOPFLT E 12 R 13 MA11 8 38 D2 12 63 nCS3 88 VDDP 14 VSSCOR 39 VDDCOR 64 nCS4 89 GPIO1 8 E E 15 VSSIO 40 D3 12 65 VSSIO 90 GPIO2 8 16 MA12 8 41 VSSCOR 66 nCS5 91 GPIO3 8 E 17 MA13 8 42 D4 12 67 nCS6 92 GPIO4 8 18 MA14 8 43 VDDIO
ページ10に含まれる内容の要旨
USB 2.0 Flash Drive Controller Datasheet Chapter 4 Pin Configuration 75 51 CLE RBIAS nRE VDDA VSSIO FS+ ALE USB+ D7 USB- D6 FS- D5 RTERM VDDIO VSSA D4 XTAL1/CLKIN VSSCORE XTAL2 D3 VSSP VDDCORE LOOPFLTR D2 USB97C242 VDDP D1 GPIO1 D0 GPIO2 ROMEN GPIO3 nIOR GPIO4 nIOW GPIO5 nMCE GPIO6 VSSIO GPIO7 nMWR nRESET nMRD VSSIO MD7 nTEST0 MD6 VDDIO MD5 nTEST1 1 25 Figure 4.1 – 100 Pin TQFP SMSC USB97C242 Page 10 Revision 1.4 (05-03-07) DATASHEET NC MA0 NC MA1 NC MA2 NC MA3 NC MA4
ページ11に含まれる内容の要旨
XTAL Data Buss USB 2.0 Flash Drive Controller Datasheet Chapter 5 Block Diagram Auto address generators 512 Bytes EP2 TX/RX Buffer B 1.25KB SRAM 512 Bytes EP2 TX/RX Buffer A Address EP0TX_BC Address 64 Bytes EP1RX 64 Bytes EP1TX 64 Bytes EP0RX Flash Media Memory EP0RX_BC Address 64 Bytes EP0TX Controller (FMC) Cards EP1TX_BC Address 32 Bit 60MHz CS[7:0] SM/ EP1RX_BC Address NAND Flash Latch phase 3 Latch phase 1 Latch phase 0, 2 DATA 8051 FMC RAMWR_A/B Address SIE NAND Flash SM ECC Flash Co
ページ12に含まれる内容の要旨
USB 2.0 Flash Drive Controller Datasheet Chapter 6 Pin Descriptions This section provides a detailed description of each signal. The signals are arranged in functional groups according to their associated interface. The “n” symbol in the signal name indicates that the active, or asserted state occurs when the signal is at a low voltage level. When “n” is not present before the signal name, the signal is asserted when at the high voltage level. The terms assertion and negation a
ページ13に含まれる内容の要旨
USB 2.0 Flash Drive Controller Datasheet BUFFER TYPE NAME SYMBOL DESCRIPTION SM nCD IPU This is the card detection signal from SM device to indicate if the device is inserted. Card Detection This pin has internal weak pull-up resistor. USB INTERFACE USB Bus USB- I/O-U These pins connect to the USB bus data signals. Data USB+ USB LOOPFLTR This pin provides the ability to supplement the internal filtering of the Transceiver transceiver with an external network, if required.
ページ14に含まれる内容の要旨
USB 2.0 Flash Drive Controller Datasheet BUFFER TYPE NAME SYMBOL DESCRIPTION MISC Crystal XTAL1/ ICLKx 12Mhz Crystal or external clock input. Input/Extern CLKIN This pin can be connected to one terminal of the crystal or can be al Clock connected to an external 12Mhz clock when a crystal is not used. Input Crystal XTAL2 OCLKx 12Mhz Crystal Output This is the other terminal of the crystal, or left open when an external clock source is used to drive XTAL1/CLKIN. It may
ページ15に含まれる内容の要旨
USB 2.0 Flash Drive Controller Datasheet Note: nMCE is normally asserted except when the 8051 is in standby mode. 6.1 Buffer Type Descriptions Table 6.2 - USB97C242 Buffer Type Descriptions BUFFER DESCRIPTION I Input IPU Input with internal weak pull-up resistor. IPD Input with internal weak pull-down resistor. IS Input with Schmitt trigger I/O4 Input/Output with 4mA drive I/OD4 Input/Open drain output … 4mA sink I/O8 Input/Output with 8mA drive I/OD8 Input/Open drain out
ページ16に含まれる内容の要旨
USB 2.0 Flash Drive Controller Datasheet Chapter 7 DC Parameters 7.1 Maximum Guaranteed Ratings o o Operating Temperature Range........................................................................................................................... 0 C to +70 C o o Storage Temperature Range ............................................................................................................................-55 to +150 C o Lead Temperature Range (soldering, 10 seconds)..
ページ17に含まれる内容の要旨
USB 2.0 Flash Drive Controller Datasheet PARAMETER SYMBOL MIN TYP MAX UNITS COMMENTS O8 Type Buffer Low Output Level V 0.4 V I = 8 mA @ V OL OL DDIO = 3.3V I = -4mA @ V OH DDIO High Output Level V 2.4 V OH = 3.3V I -10 +10 uA Output Leakage OL V = 0 to V IN DDIO (Note 7.1) I/O8 Type Buffer Low Output Level V 0.4 V I = 8 mA @ V OL OL DDIO = 3.3V I = -4 mA @ V OH DDIO High Output L
ページ18に含まれる内容の要旨
USB 2.0 Flash Drive Controller Datasheet PARAMETER SYMBOL MIN TYP MAX UNITS COMMENTS IO-U Note 7.2 Supply Current Unconfigured I 85 mA @ V V = 2.5V CCINIT DD, DDP 60 mA @ V V = DDIO, DDA 3.3V Supply Current Active I 85 110 mA @ V V = 2.5V CC DD, DDP 60 70 mA @ V V = DDIO, DDA 3.3V Supply Current Standby I 150 @ V V = 2.5V CSBY µA DD, DDP 150 @ V V = DDIO, DDA 3.3V Note 7.1 Output leakage is measured with the current pins in high impedance. Note 7.2 See A
ページ19に含まれる内容の要旨
USB 2.0 Flash Drive Controller Datasheet Chapter 8 AC Specifications Refer to the appropriate specification document in the chapter of “Reference” for each flash media device or USB interface. SMSC USB97C242 Page 19 Revision 1.4 (05-03-07) DATASHEET
ページ20に含まれる内容の要旨
USB 2.0 Flash Drive Controller Datasheet Chapter 9 Package Outline Figure 9.1 – 100 Pin TQFP Package Outline, 12x12x1.4 Body (Rev A) Table 9.1 – 100 Pin TQFP Package Parameters (Rev A) MIN NOMINAL MAX REMARKS A ~ ~ 1.60 Overall Package Height A1 0.05 ~ 0.15 Standoff A2 1.35 ~ 1.45 Body Thickness D 13.80 ~ 14.20 X Span D1 11.80 ~ 12.20 X body Size E 13.80 ~ 14.20 Y Span E1 11.80 ~ 12.20 Y body Size H 0.09 ~ 0.20 Lead Frame Thickness L 0.45 0.60 0.75 Lead Foot Length L1
