ページ1に含まれる内容の要旨
USER GUIDE
EZ Connect™ N
SMCWPCI-N
Draft 11n Wireless PCI Adapter
ページ2に含まれる内容の要旨
LIMITED WARRANTY Limited Warranty Statement: SMC Networks, Inc. (“SMC”) warrants its products to be free from defects in workmanship and materials, under normal use and service, for the applicable warranty term. All SMC products carry a standard 90-day limited warranty from the date of purchase from SMC or its Authorized Reseller. SMC may, at its own discretion, repair or replace any product not operating as warranted with a similar or functionally equivalent product, during the applicable
ページ3に含まれる内容の要旨
LIMITATION OF LIABILITY: IN NO EVENT, WHETHER BASED IN CONTRACT OR TORT (INCLUDING NEGLIGENCE), SHALL SMC BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND, OR FOR LOSS OF REVENUE, LOSS OF BUSINESS, OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE, USE, PERFORMANCE, FAILURE, OR INTERRUPTION OF ITS PRODUCTS, EVEN IF SMC OR ITS AUTHORIZED RESELLER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOM
ページ4に含まれる内容の要旨
Compliances Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interf
ページ5に含まれる内容の要旨
Table of Contents Chapter 1 - Getting Started with the SMCWPCI-N 6 Chapter 2 - Wireless LAN Networking 7 Transmission Rate (Transfer Rate) 7 Type of Wireless Networks 7 Wireless LAN Security 11 Chapter 3 - Hardware and Wireless Utility 13 About Your Draft 11n Wireless PCI Adapter 13 Package Content 13 System Requirement 13 LED Definition 13 Hardware and Wireless Utility Install
ページ6に含まれる内容の要旨
Chapter 1 - Getting Started with the SMCWPCI-N Congratulations on purchasing the SMCWPCI-N. This manual provides information for setting up and configuring the SMCWPCI-N. This manual is intended for both home users and professionals. It is not required to read some of the more technical information in this manual (such as in “Wireless LAN Networking” and “Configuring Wireless Security”) to operate and enjoy the SMCWPCI-N. It is included for your reference only. The following convention
ページ7に含まれる内容の要旨
Chapter 2 - Wireless LAN Networking This section provides background information on wireless LAN networking technology. THE INFORMATION IN THIS SECTION IS FOR YOUR REFERENCE. CHANGING NETWORK SETTINGS AND PARTICULARLY SECURITY SETTTINGS SHOULD ONLY BE DONE BY AN AUTHORIZED ADMINISTRATOR. Transmission Rate (Transfer Rate) The SMCWPCI-N provides various transmission (data) rate options for you to select. In most networking scenarios, the factory default Auto setting proves the most eff
ページ8に含まれる内容の要旨
Independent Basic Service Set (IBSS). To set up an ad-hoc network, configure all the stations in ad-hoc mode. Use the same SSID and channel for each station. 8
ページ9に含まれる内容の要旨
When a number of wireless stations are connected using a single access point, you have a Basic Service Set (BSS). 9
ページ10に含まれる内容の要旨
In the ESS diagram below, communication is done through the access points, which relay data packets to other wireless stations or devices connected to the wired network. Wireless stations can then access resources, such as a printer, on the wired network. 10
ページ11に含まれる内容の要旨
In an ESS environment, users are able to move from one access point to another without losing the connection. In the diagram below, when the user moves from BSS (1) to BSS (2) the SMCWPCI-N automatically switches to the channel used in BSS (2). Roaming in an ESS network diagram Wireless LAN Security Because wireless networks are not as secure as wired networks, it’s vital that security settings are clearly understood and applied. DO NOT ATTEMPT TO CONFIGURE OR CHANGE SECURITY SETTTINGS
ページ12に含まれる内容の要旨
D ATA ENCRYPTION WITH WEP The WEP (Wired Equivalent Privacy) security protocol is an encryption method designed to try to make wireless networks as secure as wired networks. WEP encryption scrambles all data packets transmitted between the SMCWPCI-N and the access point or other wireless stations to keep network communications private. Both the wireless stations and the access points must use the same WEP key for data encryption and decryption. There are two ways to create WEP keys in
ページ13に含まれる内容の要旨
Chapter 3 - Hardware and Wireless Utility This chapter introduces the Adapter and prepares you to use the Wireless Utility. About Your Draft 11n Wireless PCI Adapter With the Adapter, you can enjoy wireless mobility within almost any wireless networking environment. The following lists the main features of your Card. • IEEE802.11n draft v1.0 compliant • Wireless speeds up to 300Mbps • Increased speeds & coverage - up to 5x the speed of 802.11g • Fully backwards compatible with
ページ14に含まれる内容の要旨
Hardware and Wireless Utility Installation Follow the instructions below to install the PCI Card and Wireless Utility. Do not insert the EZ Connect™ N Wireless PCI Adapter until instructed. 1. Put the EZ Installation & Documentation CD in to your CD-ROM drive. The CD will auto run. If the CD does not auto run browse to your CD drive & double-click the “SMCWPCI_N.exe” file. 2. Click [Install Driver/Utility] to start the installation Wizard. 3. The installation W
ページ15に含まれる内容の要旨
4. To install to the default folder location click [Next]. It is recommended to use the default folder location unless you are an advanced user. To change the installation folder click the [Browse] button and specify a new location. Click [Next] to continue. 5. The wizard is ready to begin installation. Click [Install]. 6. A “Software Installation” warning may appear, click [Continue Anyway]. 7. Click [Finish] to exit in the installation wizard. 15
ページ16に含まれる内容の要旨
8. Turn off your computer. 9. Insert the EZ Connect™ N Wireless PCI Adapter in to an available PCI slot. IMPORTANT: For correct installation of new hardware please refer to your Computer user manual. NOTE: To install the card you may be required to remove the attached antennas. This is done by pulling the antennas from the base. 10. Once the EZ Connect™ N Wireless PCI Adapter is inserted screw on the larger 5dBi antenna to the connector marked with a green sticker. If you had to re
ページ17に含まれる内容の要旨
14. A “Hardware Installation” warning may appear, click [Continue Anyway]. 15. Click [Finish] to complete the Driver/Utility installation. 17
ページ18に含まれる内容の要旨
Using the Utility to Configure Your Network The following are explanations on how to configure and use the Utility program. After completing the installation procedure, a new icon as shown below will automatically appear in the lower right tray bar. Hold your mouse pointer over the icon, and double click the left mouse button to open the Wireless Client Utility. The Wireless Client Utility window as shown below will appear. The user can now use any of the management funct
ページ19に含まれる内容の要旨
The following table describes the items found on the Link Information screen. Wireless Network Status Profile Name The name of the current selected configuration profile. Set up the configuration name on the Profile tab. SSID Displays the wireless network name. Link Status Shows whether the station is associated to the wireless network. Network Type The type of network the station is connected to. The options include: Infrastructure (access point) Ad Hoc Wireless Mode D
ページ20に含まれる内容の要旨
channel Channel Width 20MHz only or 40/20MHz channel support Security Status Security Shows the security type – Disable, WEP, WPA/WPA2, WAP-PSK/WAP2-PSK or 802.1X Authentication Displays the authentication mode. TCP/IP Status IP Address Displays the computer's IP address. Displays subnet mask Subnet Mask Gateway Displays gateway address DNS Server Display DNS server address Site Survey Click the Site Survey tab to see available infrastructure and ad hoc networks. On this
