ページ1に含まれる内容の要旨
M37531T-ADS
Temporary Target Board for M37531RSS, M37532RSS, M37534RSS,
M37536RSS, M37540RSS, M37542RSS, M37544RSS
User's Manual
Rev.1.00
September 1, 2003
REJ10J0367-0100Z
ページ2に含まれる内容の要旨
Keep safety first in your circuit designs! • Renesas Technology Corporation and Renesas Solutions Corporation put the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary
ページ3に含まれる内容の要旨
Contents 1. Things to Check When Unpacking.....................................................................................4 2. Outline ................................................................................................................................4 3. Specifications .....................................................................................................................4 4. Setting Up ...............................................................................
ページ4に含まれる内容の要旨
1. Things to Check When Unpacking The M37531T-ADS package consists of the following products. When unpacking your package, check to see that all of these components are included. Table 1.1 Package components Temporary target board M37531T-ADS User's manual M37531T-ADS User's manual (this manual) * If you find any item missing or faulty, or any suggestion, contact your local distributor. 2. Outline The M37531T-ADS is a temporary target board used to develop software with a PC4701 emulator system.
ページ5に含まれる内容の要旨
4. Setting Up This chapter describes how to set up the M37531T-ADS. (1) Mount an emulator MCU on the M37531T-ADS. After checking the position of the No. 1 pin of the emulator MCU, mount the emulator MCU. Figure 4.1 Position of No. 1 pin of an M37531T-ADS's emulator MCU (2) Connect the white cable and black cable of the emulation pod to RESET pin (TP3) and Vss pin (TP2) of the M37531T-ADS respectively. (3) Connect a power supply (not included) to Vcc pin of the M37531T-ADS. And connect the GND ou
ページ6に含まれる内容の要旨
Figure 4.2 Connecting the M37531T-ADS CAUTION Note on Setting Up: • Always shut OFF power before connecting this product. The power ON state could destroy internal circuits. ( 6 / 12 )
ページ7に含まれる内容の要旨
5. Oscillator Circuit 5.1 Oscillator Circuit Board The M37531T-ADS has a built-in oscillator circuit board on which a 4.0MHz oscillator is mounted. J1-4: GND J1-3: Oscillator output J1-2: GND J1-1: VCC (5 V) Figure 5.1 External view of the oscillator board (OSC-2) and connector pin assignment IC1 IC1 11 10 9 8 CLK J1-3 R1 Vcc 1 2 J1-1 ** R2 X1 ,X2 14 3 4 C3 IC1 5 6 7 J1-2 C2 C1 13 12 GND * X3 J1-4 IC1 GND * X1: 5.08-mm-pitch 2-pin oscillator IC1: Inverter (Unbuffer) * X2: 2.54-mm-pitch 2-pin osc
ページ8に含まれる内容の要旨
5.2 Using the CR Oscillator Circuit Pattern There is a CR oscillator circuit pattern on the M37531T-ADS. To use the CR oscillator circuit pattern, mount R3 and C5, and remove the coated wire of JP1, then change the setting. As pins 5-6 and 2-3 of JP1 are shorted out by the coated wire when shipped from the factory, use the oscillation of OSC-2. To use the CR oscillator circuit pattern, mount R3 and C5, and remove the coated wire of JP1, then change the setting as following. When using CR oscilla
ページ9に含まれる内容の要旨
6. Pin Layout Figure 6.1 shows the pin layout of the M37531T-ADS. Figure 7.1 Pin layout of the M37531T-ADS ( 9 / 12 )
ページ10に含まれる内容の要旨
MEMO ( 10 / 12 )
ページ11に含まれる内容の要旨
M37531T-ADS User's Manual Rev.1.00 September 1, 2003 REJ10J0367-0100Z COPYRIGHT ©2003 RENESAS TECHNOLOGY CORPORATION AND RENESAS SOLUTIONS CORPORATION ALL RIGHTS RESERVED
ページ12に含まれる内容の要旨
