ページ1に含まれる内容の要旨
R0E330850ACBP0
Protection Board for M16C/60 Series M16C/62P Group and M32C/80 Series Emulator
User’s Manual
If the requirements shown in the "CAUTION" sentences are ignored,
CAUTION
the equipment may cause personal injury or damage to the products.
Renesas Tools Homepage http://www.renesas.com/tools
Rev.1.02
(1/8)
Jan. 08, 2008
REJ10J1734-0102
ページ2に含まれる内容の要旨
1. Outline LED1 Pb Free TOOL SIDE 40 40 40b 40a R0E330850ACBP0 b a The R0E330850ACBP0 is a protection board for the M16C/60 protection board Series M16C/62P Group and M32C/80 Series emulator. This product protects the emulator from improper connections by 1b 1a 1b 1a R0E330850ACBP0 J1 J2 connecting to between the converter board and emulator. R0E330850ACBP0 REV.A LED2 User's Manual (Jpn/Eng) This product is designed to protect the emulator from troubles RENESAS RENESAS R0E330850ACB
ページ3に含まれる内容の要旨
40b 1b J3 1a 40a 40b 1b J4 1a 40a 4. Connection Procedure (See Figure 2) The procedure for connecting this product is shown below. (1) Check that neither the RVC12 nor RVS12 on this product has been disconnected using a tester. RVC12 RVS12 - When the RVC12 and RVS12 are disconnected, this (1) Check neither RVC12 nor product may have been damaged because of overload. Do RVS12 have been disconnected not connect this product with the emulator or user system. before using this pro
ページ4に含まれる内容の要旨
5. Precautions CAUTION Caution to Be Taken for This Product: Be sure to connect this product to the user system, and supply power from the Vcc1 pin. Use the power pin Vcc1 with 5.5 V or less. If the Vcc1 pin is set to 5.6 V or more accidentally, the LED1 and LED2 will light up to notify it. If the LEDs light up, turn the power off immediately. If the pins protected against overvoltage are overvoltaged, the voltage of the Vcc1 pin may rise up to 5.6 V because of reverse current. W
ページ5に含まれる内容の要旨
6. Correspondence of Connectors Table 2 Correspondence of the connectors (The following signals are for the M32C/87 Group) No. Signals Protections No. Signals Protections No. Signals Protections No. Signals Protections J3-1a GND - J3-1b P86 V+,V-,I J4-1a GND - J4-1b RESET# V+,V-,I J3-2a P87 V+,V-,I J3-2b CNVss V-,I J4-2a XOUT V+,V-,I J4-2b Vss1 * - V+,V-,I V+,V-,I - J3-3a BYTE V-,I J3-3b P140 J4-3a XIN J4-3b Vcc1 * V+,V-,I V+,V-,I V+,V-,I J3-4a P141 V+,V-,I J3-4b P14
ページ6に含まれる内容の要旨
7. Troubleshooting If you have trouble when using this product with connected to the emulator, refer to the following procedures. Table 3 Items to check when having trouble with this product used Type Problems Items to check Improper After turning off the power, verify that this product is connected to the user system, and Used without the user system. use then use it. Installed on a wrong position. Applied more than 5.5[V] voltage This product and the emulator may have been damage
ページ7に含まれる内容の要旨
8. Appendix Table 4 Correspondence of part numbers and signals Signals J1J2side resistors Diode J3J4 side resistors Remark CNVss RCNV1 (DCNV1), D87 RCNV2 DCNV1 unmount BYTE RBYT1 (DBYT1), D94 RBYT2 DBYT1 unmount RESET# RRES1 DRES1 RRES2 XIN RXIN1 DXIN1 RXIN2 XOUT RXO1 DXO1 RXO2 P00-P07 N6,N17 D10,D13,D21,D56,D68,D73 N42,N50 P10-P17 N3,N10 D1,D7,D14,D49,D55,D59 N38,N45 P20-P27 N1,N7 D2,D8,D46,D47,D48,D51 N35,N41 P30-P37 N5,N8,R3 D6,D30,D43,D53,D54 N36,N40,R15 P40-P47 N11,N15
ページ8に含まれる内容の要旨
J1J2 side R Diode J3J4 side R Vcc1 Vcc1 J2-3b J4-3b 0.5A Fuse 0 RVC12 Vcc2 Vcc2 RVC2 Vss Vss J2-2b 0.5A Fuse J4-2b RVS12 0 0 AVcc AVcc RAVC1 RAVC2 J1-12a J3-12a 0 0 VREF VREF RVRF1 RVRF2 J1-12b J3-12b 0 0 AVss AVss RAVS1 RAVS2 J1-13b J3-13b CNVss 22 22 CNVss BYTE 22 22 P70,P71 P70,P71 RESET#, RESET#, 22 22 XIN,XOUT XIN,XOUT otherPort otherPort UDZS5.6B Power ZD6 block 110 0 Vcc1 Vcc1 RVC10 J1-17b J3-17b ZD3 0 CV3 RVC11 Vcc1 Vcc1 ZD5 CV5 GND GND (Note: Diode is Rohm RB731U) Figure 5 Conn
