ページ1に含まれる内容の要旨
VIEW Certified Configuration Guide
Trapeze Networks
Mobility System for MP-422 Access Points
June 2008 Edition
1725-36060-001
Version D
ページ2に含まれる内容の要旨
Configuration Guide Trademark Information Notice Polycom® and the logo designs Polycom, Inc. has prepared this document for SpectraLink® use by Polycom personnel and customers. The LinkPlus drawings and specifications contained herein Link are the property of Polycom and shall be neither NetLink reproduced in whole or in part without the prior SVP written approval of Polycom, nor be implied to Are trademarks and registered trademarks of grant any license to make, use, or sell equip
ページ3に含まれる内容の要旨
Trapeze Networks: Mobility System for MP 422 Access Points Introduction Polycom’s Voice Interoperability for Enterprise Wireless (VIEW) Certification Program is designed to ensure interoperability and high performance between SpectraLink Wireless Telephones and wireless LAN (WLAN) infrastructure products. The products listed below have been thoroughly tested in Polycom’s lab and have passed VIEW Certification. This document details how to configure the Trapeze Networks Mobility Exchan
ページ4に含まれる内容の要旨
Configuration Guide Service Information The AP must support SpectraLink Voice Priority (SVP). Contact your AP vendor if you need to upgrade the AP software. If you encounter difficulties or have questions regarding the configuration process of the Mobility Exchange, please contact Trapeze Networks by calling 866 TRPZ TAC or 925 474 2400 or by e-mailing support@trapezenetworks.com. Known Limitations During VIEW Certification testing, the following limitations were discovered. • R
ページ5に含まれる内容の要旨
Trapeze Networks: Mobility System for MP 422 Access Points Network Topology The following topology was tested during VIEW Certification. It is important to note that these do not necessarily represent all “Certified” configurations. Both Layer-2 and Layer-3 roaming were tested. Layer-3 roaming of SpectraLink Wireless Telephones requires the use of a generic routing encapsulation (GRE) tunnel. SpectraLink 8000 Telephony Gateway SpectraLink 8000 SVP Server SpectraLink Wireles
ページ6に含まれる内容の要旨
Configuration Guide Access Point Setup and Configuration Installing software Trapeze Mobility Exchange firmware cannot be downloaded from the SpectraLink website. Therefore, you must use the software that was shipped with your product, or contact Trapeze Networks for the latest software release. Command, comment, and screen text key In the sections below you will find commands, comments and system responses or other screen-displayed information involved in the configuration process.
ページ7に含まれる内容の要旨
Trapeze Networks: Mobility System for MP 422 Access Points Service profile commands (SSID & security policy setup) WPA2-PSK Assume you are creating service profile “vowlan-wpa2” to define the ESSID “phones,” as well as a WPA2-PSK security policy. The following commands are needed to setup the service for MP access points: set service-profile Voice ssid-name vowlan-wpa2 # sets the name of the service profile and SSID to vowlan-wpa2 set service-profile Voice auth-fallthru last-resort
ページ8に含まれる内容の要旨
Configuration Guide # defines a passphrase set service-profile Voice auth-psk enable # enables pre-shared key authentication set service-profile Voice auth-dot1x disable # disables 802.1x authentication set service-profile Voice attr vlan-name default # maps the handsets to the vlan named default Radio profile commands Assume you are creating radio profile “voice” for all radios that will be providing voice services. The following commands are needed to setup the radio profile for
ページ9に含まれる内容の要旨
Trapeze Networks: Mobility System for MP 422 Access Points Radio configuration During VIEW Certification, the MP access points were tested directly connected to a port on the MX (e.g. port 1). The following commands will configure a specific access point’s radio to support the voice service: set ap 1 radio 1 mode disable # if the radio is currently enabled. Radio 1 is the 802.11b/g radio set ap 1 radio 1 radio-profile voice mode enable # maps radio to the radio-profile and enables it
ページ10に含まれる内容の要旨
Configuration Guide Subnet roaming configuration between multiple MX switches To set up subnet roaming between two switches, a mobility domain must be configured on both switches. Choose one of the switches to be the “seed” switch. The IP addresses used in mobility domain configuration must use the system IP address of each switch). The following commands are performed on the seed MX switch: set system ip-address 1.1.1.1 set mobility-domain mode seed domain-name se
ページ11に含まれる内容の要旨
Trapeze Networks: Mobility System for MP 422 Access Points Checking the configuration Once the switch is configured, issue the following command at the command prompt to check the SVP settings: sh ap qos-stats The following information should be displayed (repeat the command to see changes): CoS Queue Tx =========================== port: 1 radio: 1 1,2 Background 0 0,3 BestEffort 604 4,5 Video 0 6,7 Voice 79106 # Voice
ページ12に含まれる内容の要旨
Configuration Guide Configuration File (For Reference Only) The following configuration file was used during VIEW Certification testing. The configuration below includes all configuration attributes, including defaults. Use the command show configuration all for this detailed version. To only see non-default configuration values, use the command show configuration. Note: All of the lines below are commands, except for those preceded by the # symbol, which denotes a comment. # General
ページ13に含まれる内容の要旨
Trapeze Networks: Mobility System for MP 422 Access Points set service-profile VoWLAN-WPA wep active-multicast- index 1 set service-profile VoWLAN-WPA wpa-ie disable set service-profile VoWLAN-WPA rsn-ie enable set service-profile VoWLAN-WPA cipher-tkip enable # for WPA this should be disabled set service-profile VoWLAN-WPA cipher-ccmp enable # for WPA this should be enabled set service-profile VoWLAN-WPA cipher-wep104 disable set service-profile VoWLAN-WPA cipher-wep40 disable set s
ページ14に含まれる内容の要旨
Configuration Guide set radio-profile RealRadio auto-tune power-backoff- timer 10 set radio-profile RealRadio active-scan disable set radio-profile RealRadio qos-mode svp set radio-profile default 11g-only disable set radio-profile default beacon-interval 100 set radio-profile default dtim-interval 1 set radio-profile default max-tx-lifetime 2000 set radio-profile default max-rx-lifetime 2000 set radio-profile default rts-threshold 2346 set radio-profile default short-retry 5 set r
ページ15に含まれる内容の要旨
Trapeze Networks: Mobility System for MP 422 Access Points set ap 2 name MP02 set ap 2 bias high set ap 2 blink disable set ap 2 upgrade-firmware enable set ap 2 group none set ap 2 radio 1 channel 6 tx-power 2 radio-profile default mode disable set ap 2 radio 1 auto-tune max-power default min-client- rate 5.5 max-retransmissions 10 set ap 2 radio 2 channel 36 tx-power 17 radio-profile default mode disable set ap 2 radio 2 auto-tune max-power default min-client- rate 24 max_retransm
ページ16に含まれる内容の要旨
Configuration Guide set spantree uplinkfast disable set spantree fwddelay 15 vlan 1 set spantree hello 2 vlan 1 set spantree maxage 20 vlan 1 set spantree priority 32768 vlan 1 set spantree disable vlan 1 set igmp disable vlan 1 set igmp proxy-report enable vlan 1 set igmp querier disable vlan 1 set igmp mrsol disable vlan 1 set igmp version 2 vlan 1 set igmp mrsol mrsi 30 vlan 1 set igmp qi 125 vlan 1 set igmp oqi 255 vlan 1 set igmp qri 100 vlan 1 set igmp lmqi 10 vlan 1 s
