ページ1に含まれる内容の要旨
8-Port Managed Industrial Ethernet Switch
ISW-800M
User's Manual
ページ2に含まれる内容の要旨
Trademarks c Copyright PLANET Technology Corp. 2006. Contents subject to which revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners. Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness
ページ3に含まれる内容の要旨
Table of Contents 1. INTRODUCTION ................................................................................................................... 5 1.1 Packet Contents.............................................................................................................. 5 1.2 How to Use This Manual ................................................................................................. 5 1.3 Product Feature..................................................................
ページ4に含まれる内容の要旨
4.12 IP Configuration........................................................................................................... 35 4.13 SNTP Configuration .................................................................................................... 36 4.14 IP Security ................................................................................................................... 38 4.15 RSTP Configuration .............................................................................
ページ5に含まれる内容の要旨
1. INTRODUCTION The 8-Port 10/100TX with redundant ring Web management industrial switch is a cost- effective solution and meets the high reliability requirements demanded by industrial applications. The switch can be easily managed through the Web GUI. It also provides the redundant ring function that can prevent the network connection failure. 1.1 Packet Contents Check the contents of your package for following parts: ▫ Industrial Fast Ethernet Switch x1 ▫ DIN-Rail kit (screwed on the
ページ6に含まれる内容の要旨
▫ CSMA/CD Protocol ▫ RJ-45 Port support auto MDI/MDI-X function ▫ 2K MAC address table ▫ 1Mbit memory buffer ▫ 2.0Gbps back-plane ▫ Wide-range redundant power design ▫ Store and forward switch architecture ▫ DIN rail and 3-way wall mount design Industrial Conformance ▫ 12~48V DC, redundant power with polarity reverse protect function ▫ 0 to 60 Degree C operation temperature ▫ IP-30 Aluminum case ▫ Relay alarm for port breakdown, power failure ▫ FCC Class A, CE compatibility ▫ Fre
ページ7に含まれる内容の要旨
MAC address 2K Memory Buffer 1Mbit Network Cable 10Base-T : 2-pair UTP/STP Cat 3, 4, 5 cable 100Base-TX: 2-pair UTP/STP Cat. 5 cable 10Base-T: EIA/TIA-568 100-ohm (100m) LED Per port: Link/Activity (Green), Full duplex/Collision (Yellow) Per unit: Power (Green), Power 1 (Green), Power 2 (Green), Fault (Yellow), Master (Green) Back-plane 1.6Gbps Packet throughput ability 1.19Mpps@64bytes (8TX) Power Supply 12 to 48 VDC, Redundant power with polarity reverse protection function Power Co
ページ8に含まれる内容の要旨
128kbps, 256Kbps, 512Kbps, 1MB, 2MB, 4MB, and 8MB. Ingress filter packet type combination rules are Broadcast/Multicast/Unknown Unicast packet, Broadcast/Multicast packet, Broadcast packet only and all of packet. The packet filter rate can be set follow as:1Mbps 2Mbps 4Mbps 8Mbps 16Mbps 32Mbps 64Mbps. Port mirror Support TX packet only or both of TX and RX packet. Packet filter 4 selection rules for different type of packet combination: 1. All of packet 2. Broadcast/ multicast/ unknown
ページ9に含まれる内容の要旨
2. HARDWARE INSTALLATION This section describes the functionalities of the Switch's components and guides how to install it on the rack or mount to the wall. Basic knowledge of networking is assumed. Please read this chapter completely before continuing. 2.1 Product Description The PLANET Management Industrial Ethernet Switch provides substation hardened, fully managed, Ethernet switches specifically designed to operate reliably in electrically and environmentally harsh environments. It p
ページ10に含まれる内容の要旨
Figure 2-1 ISW-800M Front Panel 2.1.3 LED Indications LED Status Meaning Green The switch unit is power on. Power Off The switch unit is no power input. Green Power on Power 1 Off No power inputs Green Power on Power 2 Off No power inputs Yellow Power failure or UTP port failure or Fiber port failure Fault Off No Power failure or UTP port failure or Fiber port failure occurs Green The industrial switch is the master of redundant ring group. R. M. (Ring Master) Off The indu
ページ11に含まれる内容の要旨
Off No device attached Yellow The port is operating in full-duplex mode. FDX/COL Blinks Collision of Packets occurs in the port. (Port 7 & 8) Off The port in half-duplex mode or no device attached 2.1.4 Reset Button The reset button provides user a quick and easy way to restart and set the configuration back to default value. Restart: press the button for 2 seconds and release. Set to factory default value: press the button for 5 seconds and release. The switch will set all confi
ページ12に含まれる内容の要旨
OFF Disable port 6 Alarm 6 Enable port 6 Alarm. If the port’s link fails, the fault LED will ON light up. OFF Disable port 7 Alarm 7 Enable port 7 Alarm. If the port’s link fails, the fault LED will ON light up. OFF Disable port 8 Alarm 8 Enable port 8 Alarm. If the port’s link fails, the fault LED will ON light up. OFF Disable the ring master function. 9 Enable the switch as the ring master in the redundant ring ON group. [NOTE] 1. When port alarm function is enabled, the
ページ13に含まれる内容の要旨
V - V + V - V + 1. Insert the positive and negative wires into the V+ and V- connector on the terminal block connector. 2. To tighten the wire-clamp screws for preventing the DC wires to loose. Power Notice: The wire range of terminal block is from 12~ 24 AWG. 2.1.8 Wiring the Fault Alarm Contact The fault alarm contact is in the middle of terminal block connector as below figure shows. By inserting the wires and set the DIPswitch at "ON" status,
ページ14に含まれる内容の要旨
Fault Alarm Contact The open circuit will form when the power failure or port link failure. 24V DC Buzzer 24V Battery The fault alarm device will send a warning signal t warn the user, ex: alarm sound or flash light. 2.2 Mounting Installation This section describes how to install the Ethernet Switch and make connections to it. Please read the following topics and perform the procedures in the order being presented. 2.2.1 DIN-Rail mounting The DIN-Rail is screwed on the industrial swit
ページ15に含まれる内容の要旨
Step2: Lightly push the button of DIN-Rail into the track. Step3: Check the DIN-Rail is tightly on the track. Step4: To remove the industrial switch from the track, reverse steps above. 2.2.2 Wall Mount Plate Mounting To install the switch on the wall, please follows the instructions described below. Step1: Remove the DIN-Rail from the industrial switch; loose the screws to remove the DIN-Rail. Step2: Place the wall mount plate on the rear panel of the industrial switch.
ページ16に含まれる内容の要旨
Step3: Use the screws to screw the wall mount plate on the industrial switch. Step4: Use the hook holes at the corners of the wall mount plate to hang the industrial switch on the wall. Step5: To remove the wall mount plate, reverse steps above.
ページ17に含まれる内容の要旨
3. NETWORK INSTALLATION 3.1 Hardware Installation In this paragraph, we will describe how to install the 8-Port 10/100TX with redundant ring Web management industrial switch and the installation points for attention. 1. Unpacked the Industrial switch. 2. Check the DIN-Rail is screwed on the Industrial switch. If the DIN-Rail is not screwed on the Industrial switch. Please refer to DIN-Rail Mounting section for DIN-Rail installation. If you want to wall mount the Industrial switch, then pl
ページ18に含まれる内容の要旨
3.3 Redundant Ring Application The industrial switch supports the redundant ring protocol that can help your network system to recovery from network connection failure within 300ms or less, and make your network system more reliable. The redundant ring algorithm is like as spanning tree protocol (STP) algorithm but it has faster recovery time than STP. The following figure is a sample redundant ring application.
ページ19に含まれる内容の要旨
3.4 Coulping Ring Application In the network, it may have more than one redundant ring group. By using the coupling ring function can connect each redundant ring for the redundant backup. It can ensure the transmissions between two ring groups will no failure. The following figure is a sample of coupling ring application.
ページ20に含まれる内容の要旨
3.5 Dual Homing Application Dual Homing function is to prevent the connection lose between redundant ring group and upper level/core switch. Assign two ports to be the Dual Homing ports that one is working port and one is backup port in the redundant ring group. The backup port that has smaller MAC address value will be selected by switch automatically. The Dual Homing function only work when the redundant ring function is active. The maximum Dual Homing port is two in a redundant ring grou
