ページ1に含まれる内容の要旨
HZ800
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
Contents Congratulations Your headset 3 Charge it 4 Basics 5 Pair & connect 0 Be clear 3 Calls 4 Talk time 5 Status light 6 Settings 7 Problems? 8 Safety, Regulatory & Legal
ページ4に含まれる内容の要旨
Congratulations Your Motorola Finiti™ headset delivers the best sound in any condition and Without raising your voice. CrystalTalk™ dual microphones are used for everyday noise cancellation, and the stealth mode for windy or extreme conditions. Some other cool features: • Hear and reply to phone text messages with MotoSpeak™. • Hear the caller’s name and use your voice to answer or ignore calls. • Stream Bluetooth® music from your phone. • Voice prompts to guide you on connections, battery lev
ページ5に含まれる内容の要旨
Your headset the important parts side view Call Ear Power Button Loop Switch MicroUSB Status Charging Light Connector Earhook Volume the Earpiece with Buttons Stealth the Stealth Mode Mode Sensor Button Warning:Do not apply pressure or squeeze the stealth mode sensor (small rubber balloon), as it can damage the parts inside and will void the warranty. 3
ページ6に含まれる内容の要旨
Charge it let’s get you up and running Status Light Red/Yellow - charging Green - fully charged While your headset is charging, you won’t be able to use it. Note: Your battery is designed to last the life of your product. It should only be removed by a recycling facility. Any attempt to remove or replace your battery will damage your headset. 4
ページ7に含まれる内容の要旨
Basics a few essentials to get you started Change ear fitting Your headset comes with multiple ear fittings. Left Right Large Medium Small Ear Ear Ear Ear Ear Spring Spring Loop Loop Loop Choose your ear fitting (loop or spring) so your headset is comfortable. Lift the current ear fitting up and slide it off the headset in an upward direction. 5
ページ8に含まれる内容の要旨
Basics Slide the new ear loop or spring downward onto the earpiece, then align and push the bottom onto the Groove groove. Wear it Bend the ear loop or spring and insert the the Stealth earpiece into your ear. Make sure the mode sensor stealth mode sensor is in contact with your ear canal. Place the ear loop or spring in the bend of your ear. Ear canal 6
ページ9に含まれる内容の要旨
Basics Flex the earhook and loop it over your ear, and point the headset microphone towards your mouth. Turn it on & off Listen to music Note: This feature is phone dependent. Your headset allows you to stream Bluetooth music from your phone. Music playback is started and controlled from your phone. 7
ページ10に含まれる内容の要旨
Basics While a call is active, music pauses. When the call ends, music resumes playing. Enhanced call features Tell headset to answer or ignore calls Use your voice to answer or ignore an incoming call: • say “answer” to answer the call • say “ignore” to ignore the call Note: This feature does not work for second incoming calls. Hear caller’s name If your phone knows your caller’s name, then you hear “call from ” on an incoming call. 8
ページ11に含まれる内容の要旨
Basics Clean your headset Keep your headset clean and dry. High humidity or perspiration can make the ear fitting feel slippery. Remove the ear fitting and wipe it with a soft cloth to remove dirt and moisture. Note: Be very careful when wiping near the stealth mode sensor. Also check for any debris that may be blocking the small speaker port on the ear fitting.
ページ12に含まれる内容の要旨
Pair & connect connect and go Pair & connect with your phone Turn off any Bluetooth® devices previously paired with your headset. Turn on the Bluetooth feature on your phone. Put the headset on your ear (see “Wear it” on page 6). Turn on your headset (see “Turn it on & off” on page 7). The status light becomes steadily lit in blue and you hear “ready to pair”. Follow the voice prompts to connect your phone to your headset.
ページ13に含まれる内容の要旨
Pair & connect Pair & connect a second phone Turn off first phone and any other Bluetooth devices previously paired with your headset. Turn your headset off. Turn on the Bluetooth feature on your phone. Put the headset on your ear. Turn on your headset. The status light becomes steadily lit in blue and you hear “ready to pair”. Follow the voice prompts to connect your phone to your headset. Note:
ページ14に含まれる内容の要旨
Pair & connect Test your call connection Place the headset on your ear. On your phone, dial a phone number and press the Call/Send key. If your phone and headset are successfully connected, you hear ringing on the headset.
ページ15に含まれる内容の要旨
Be clear your voice, not all the noise Always be heard during calls with the CrystalTalk dual microphones and the stealth mode sensor: • CrystalTalk is always on to cancel out everyday background noise. • The stealth mode can be turned on when noise and wind get really bad to shut out all background noise. the Stealth Mode Button Turn on the stealth mode Press the Stealth Mode button and listen for the “stealth mode on” or “stealth mode off” prompt. Note: Make sure the stealth mode sensor i
ページ16に含まれる内容の要旨
Calls it’s good to talk Note: Some features are phone/network dependent. To... answer call Say “answer” or press the Call button. Say “ignore” or press and hold a Volume button until reject call you hear a tone. make a voice dial call Press the Call button and you hear a tone. redial last call Press and hold the Call button until you hear a tone. mute or unmute a call Press both Volume buttons. end a call Press the Call button. Answer second incoming call Press the Call button. Reject second in
ページ17に含まれる内容の要旨
Talk time check your chat time Press both Volume buttons while not on a call. if light shows... and/or you hear… your remaining talk time is.. red “battery level is low" less than 1.5 hours yellow “battery level is medium" between 1.5 to 3.5 hours green “battery level is high” more than 3.5 hours To save battery power, turn off the headset when not using it. 5
ページ18に含まれる内容の要旨
Status light know your headset If light shows... your headset is... three blue flashes powering on/off steady blue in pairing/connect mode rapid blue/purple flashes connecting to your phone quick blue flash receiving or making a call on phone 1 quick purple flash receiving or making a call on phone 2 slow blue pulse on a call slow blue flash in standby (not on a call—connected to one phone) slow green flash in standby (not on a call—connected to two phones) slow red flash idle (not connected to
ページ19に含まれる内容の要旨
Settings make some changes Press and hold the Call button while turning on the headset to turn these features on/off: • Reset to factory default Caution: This action erases all pairing information stored in your headset. • Caller ID • Voice prompts • Multipoint (two phone) connections Follow the voice prompts to make changes to these settings. 7
ページ20に含まれる内容の要旨
Problems? we’ve got solutions My headset will not enter pairing mode Make sure that any devices previously paired with the headset are turned off. If the status light is not steadily lit in blue, turn off both the other device and headset, wait 10 seconds, then turn headset back on. Wait for the status light to become steadily lit in blue, indicating the headset is now in pairing mode. My phone doesn't find my headset when searching. Make sure the status light on your headset is steadily lit
