ページ1に含まれる内容の要旨
User’s Guide
Shop online at
www.omega.com
e-mail: info@omega.com
OMG-USB-SER-2
Two Port RS-232/422/485 to USB Adaptor
ページ2に含まれる内容の要旨
Manual No. M-3899 Contents INTRODUCTION..........................................................................1 OVERVIEW................................................................................................1 WHAT’S INCLUDED................................................................................1 INSTALLATION ..........................................................................2 OPERATING SYSTEM INSTALLATION...............................................
ページ3に含まれる内容の要旨
APPENDIX D - ASYNCHRONOUS COMMUNICATIONS ...............14 APPENDIX E - COMPLIANCE NOTICES .....................................15 FEDERAL COMMUNICATIONS COMMISSION STATEMENT............ 15 CANADIAN RADIO INTERFERENCE REGULATIONS......................... 15 EMC DIRECTIVE STATEMENT........................................................... 16 Figures: Figure 1: Switch SW2...........................................................................................5 Figure 2: RS422/485 I
ページ4に含まれる内容の要旨
Introduction Introduction Overview The OMG-USB-SER-2 equips the PC with 2 USB to RS-232/422/485 Asynchronous serial ports providing a versatile interface for common serial needs. The advantage of this product over more traditional approaches is that it does not require opening the computer case, nor does it require resources such as I/O ports or IRQ’s. It does require a system that supports USB both in terms of hardware and operating system. What’s Included The OMG-USB-SER-2 is shi
ページ5に含まれる内容の要旨
Installation Installation Operating System Installation Choose Install Software at the beginning of the CD and install SeaCOM. System Installation The screen captures below are taken from a Windows 98 installation. Your particular operating system may differ slightly from what is shown based on your version of Windows. The OMG-USB-SER-2 can be connected to any upstream type “A” port either at the PC host or an upstream hub. The OMG-USB-SER-2 is hot pluggable, meaning there is
ページ6に含まれる内容の要旨
Installation You can access your new COM: ports by using the assigned COM: identifiers as shown above. In this case, it is COM 3 and 4. However, this assignment will vary from system to system. At this point, the hardware is recognized and ready to use. OMG-USB-SER-2 Page 3
ページ7に含まれる内容の要旨
Configuration Configuration Original configuration This device ships with the following configuration. 422 mode, 120 ohm termination, 1K ohm pull up on RX+ 1K ohm pull down on RX- In order to change this configuration the box must be opened. Do this by removing the four screws located on the bottom. When reassembling please note that the top and bottom are keyed to fit in only one direction. Electrical Interface Selection Each of the two ports on the OMG-USB-SER-2 can be
ページ8に含まれる内容の要旨
ON OFF 1 2 3 4 5 6 7 8 9 10 Configuration Switch Descriptions SW4 Port 1 L L T PU Port 2 PD L L T PU PD Figure 1: Switch SW4 L 485 option, OFF for 422. OFF: No effect ON : Connects TX+ to RX+ for two-wire operation L 485 option, OFF for 422. OFF: No effect ON : Connects TX- to RX- for two-wire operation PU 485 option, OFF for 422. OFF: No effect ON : Adds a 1 K ohm pull-up resistor to RX+ PD 485 option, OFF for 422. OFF: No effec
ページ9に含まれる内容の要旨
ON OFF 1 2 3 4 Configuration Switch Examples SW3 485 1 NE 1 485 2 NE 2 Figure 2: RS422/485 Interface Configuration 485 Mode Selection OFF : 422 Mode The transmitter lines TX+ and TX- are always driven ON : 485 Mode The transmitter lines TX+ and TX- are switched to high impedance when the device is not actively transmitting data NE 485 option, OFF for 422 OFF : The receiver is always enabled. In a two-wire setup the receiver will echo back all transmitted data
ページ10に含まれる内容の要旨
ON OFF 1 2 3 4 5 6 7 8 9 10 Configuration Switch Examples Continued Port 2 Port 1 RS 422/485 SW4 RS 232 RS 422/485 RS 232 Port 1 L L T PU Port 2 PD L L T PU PD E7 E8 E6 E5 Figure 3: Electrical Interface Configuration Port 1 : RS-232 The corresponding shunt is in the 232 position. The switches will have no effect. Port 2 : RS-485 two wire communication with no echo. The corresponding shunt is in the 422/485 position. Switche
ページ11に含まれる内容の要旨
Technical Technical Description The OMG-USB-SER-2 utilizes two USB UARTs. These chips feature programmable baud rate, data format, 128 byte Dual Port TX Buffer, and 384 byte Dual Port RX Buffer. The RS-232/422/485 transceiver supports data rates up to 921.6K baud for RS-422/485 and up to 460.8K baud for RS-232. Features • Hot pluggable device that does not require opening the case • No system resources are required (i.e. I/O ports or IRQ’s) • LED status indicators for USB Enabled and
ページ12に含まれる内容の要旨
Specifications Specifications Environmental Specifications Specification Operating Storage Temperature Range 0º to 50º C -20º to 70º C (32º to 122º F) (-4º to 158º F) Humidity Range 10 to 90% R.H. 10 to 90% R.H. Non-Condensing Non-Condensing Manufacturing • All Printed Circuit boards are built to UL 94V0 rating and are 100% electrically tested. These printed circuit boards are solder mask over bare copper or solder mask over tin nickel. Power Consumption This device is a
ページ13に含まれる内容の要旨
Appendix A – Troubleshooting Appendix A - Troubleshooting Serial Utility test software is supplied with the adapter and will be used in the troubleshooting procedures. Using this software and following these simple steps, most common problems can be eliminated without the need to call Technical Support. 1. If your adapter isn’t working, first check to make sure that USB support is enabled in the System BIOS and it is functioning properly in the operating system. This can be done by us
ページ14に含まれる内容の要旨
Appendix B – How To Get Assistance Appendix B - How To Get Assistance Please refer to Appendix A - Troubleshooting prior to calling Technical Support. 1. Read this manual thoroughly before attempting to install the adapter in your system. 2. When calling for technical assistance, please have your user manual and current adapter settings. If possible, please have the adapter connected in a computer ready to run diagnostics. 3. Omega Engineering maintains a home page on the Inte
ページ15に含まれる内容の要旨
Appendix C - Electrical Interface Appendix C - Electrical Interface RS-232 Quite possibly the most widely used communication standard is RS-232. This implementation has been defined and revised several times and is often referred to as RS-232 or EIA/TIA-232. The IBM PC computer defined the RS-232 port on a 9 pin D sub connector and subsequently the EIA/TIA approved this implementation as the EIA/TIA-574 standard. This standard is defined as the 9-Position Non-Synchronous Interface bet
ページ16に含まれる内容の要旨
Appendix C - Electrical Interface RS-485 RS-485 is backwardly compatible with RS-422; however, it is optimized for partyline or multi-drop applications. The output of the RS-422/485 driver is capable of being Active (enabled) or Tri-State (disabled). This capability allows multiple ports to be connected in a multi-drop bus and selectively polled. RS-485 allows cable lengths up to 4000 feet and data rates up to 10 Megabits per second. The signal levels for RS-485 are the same as those d
ページ17に含まれる内容の要旨
Appendix D - Asynchronous Communications Appendix D - Asynchronous Communications Serial data communications implies that individual bits of a character are transmitted consecutively to a receiver that assembles the bits back into a character. Data rate, error checking, handshaking, and character framing (start/stop bits) are pre-defined and must correspond at both the transmitting and receiving ends. Asynchronous communications is the standard means of serial data communication for
ページ18に含まれる内容の要旨
Appendix E - Compliance Notices Appendix E - Compliance Notices Federal Communications Commission Statement This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
ページ19に含まれる内容の要旨
Appendix E - Compliance Notices EMC Directive Statement Products bearing the CE Label fulfill the requirements of the EMC directive (89/336/EEC) and of the low-voltage directive (73/23/EEC) issued by the European Commission. To obey these directives, the following European standards must be met: EN55022 Class B - ‘Limits and methods of measurement of radio interference characteristics of information technology equipment’ EN55024-‘Information technology equipment Immunity
ページ20に含まれる内容の要旨
WARRANTY/DISCLAIMER OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a period of 13 months from date of purchase. OMEGA’s WARRANTY adds an additional one (1) month grace period to the normal one (1) year product warranty to cover handling and shipping time. This ensures that OMEGA’s customers receive maximum coverage on each product. If the unit malfunctions, it must be returned to the factory for evaluation. OMEGA’s Customer Service Department w
