ページ1に含まれる内容の要旨
Part No. 312410-A Rev 00
November 2000
600 Technology Park Drive
Billerica, MA 01821-4130
Installing and Operating
AN/DC and ANH-8/DC
Systems
ページ2に含まれる内容の要旨
Copyright © 2000 Nortel Networks All rights reserved. November 2000. The information in this document is subject to change without notice. The statements, configurations, technical data, and recommendations in this document are believed to be accurate and reliable, but are presented without express or implied warranty. Users must take full responsibility for their applications of any products specified in this document. The information in this document is proprietary to Nortel Networks NA I
ページ3に含まれる内容の要旨
EC Declaration of Conformity This product conforms (or these products conform) to the provisions of Council Directive 89/336/EEC and 73/23/EEC. Japan/Nippon Requirements Only Voluntary Control Council for Interference (VCCI) Statement Taiwan Requirements Bureau of Standards, Metrology and Inspection (BSMI) Statement Canada Requirements Only Canadian Department of Communications Radio Interference Regulations This digital apparatus (BN router) does not exceed the Class A limits for radio-noise e
ページ4に含まれる内容の要旨
Canada Requirements Only (continued) Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment. Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if presen
ページ5に含まれる内容の要旨
FCC Part 68 Compliance Statement This equipment complies with Part 68 of FCC Rules. All direct connections to telephone network lines must be made using standard plugs and jacks compliant with FCC Part 68. Please note the following: 1. You are required to request service from the telephone company before you connect the unit to a network. When you request service, you must provide the telephone company with the following data: • When you request T1 Service, you must provide the telephone compa
ページ6に含まれる内容の要旨
Nortel Networks NA Inc. Software License Agreement NOTICE: Please carefully read this license agreement before copying or using the accompanying software or installing the hardware unit with pre-enabled software (each of which is referred to as “Software” in this Agreement). BY COPYING OR USING THE SOFTWARE, YOU ACCEPT ALL OF THE TERMS AND CONDITIONS OF THIS LICENSE AGREEMENT. THE TERMS EXPRESSED IN THIS AGREEMENT ARE THE ONLY TERMS UNDER WHICH NORTEL NETWORKS WILL PERMIT YOU TO USE THE SO
ページ7に含まれる内容の要旨
for the security of its own data and information and for maintaining adequate procedures apart from the Software to reconstruct lost or altered files, data, or programs. 4. Limitation of liability. IN NO EVENT WILL NORTEL NETWORKS OR ITS LICENSORS BE LIABLE FOR ANY COST OF SUBSTITUTE PROCUREMENT; SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES; OR ANY DAMAGES RESULTING FROM INACCURATE OR LOST DATA OR LOSS OF USE OR PROFITS ARISING OUT OF OR IN CONNECTION WITH THE PERFORMANCE OF THE S
ページ8に含まれる内容の要旨
ページ9に含まれる内容の要旨
Contents Preface Before You Begin ............................................................................................................xvii Text Conventions ...........................................................................................................xviii Acronyms .........................................................................................................................xix Hard-Copy Technical Manuals .............................................................
ページ10に含まれる内容の要旨
Connecting a Management Console or Modem ...........................................................1-12 Connecting a Terminal Console .............................................................................1-12 Connecting a PC Console ......................................................................................1-14 Connecting a Modem .............................................................................................1-16 Connecting to the DC Power Source ...............
ページ11に含まれる内容の要旨
Chapter 3 Starting the AN/DC and ANH-8/DC About Software Installation .............................................................................................3-1 Boot Options ............................................................................................................3-2 Installing the Flash Memory Card ...................................................................................3-3 Using EZ Install .......................................................................
ページ12に含まれる内容の要旨
Appendix B Using Local Boot (the Quick-Start Procedure) Filling Out the Quick-Start Worksheets ......................................................................... B-2 Global Information Worksheet ................................................................................. B-3 Router Protocol Worksheets ................................................................................... B-5 Wide Area Protocol Worksheets .................................................................
ページ13に含まれる内容の要旨
Figures Figure 1-1. Mounting Hardware ..................................................................................1-2 Figure 1-2. Console Cables ........................................................................................1-3 Figure 1-3. Attaching Flange Brackets to the AN/DC .................................................1-7 Figure 1-4. Installing the AN/DC in a Rack .................................................................1-8 Figure 1-5. Mounting the AN/DC on a Wall
ページ14に含まれる内容の要旨
Figure 2-17. Connecting a PC Console to the ANH-8/DC ..........................................2-23 Figure 2-18. Connecting a Modem to the ANH-8/DC .................................................2-25 Figure 2-19. ANH-8/DC Power Switch and DC Terminals ..........................................2-26 Figure 2-20. Attaching the ANH-8/DC Power Input Cables ........................................2-27 Figure 2-21. Attaching the ANH-8/DC Earth Ground Cable .......................................2-2
ページ15に含まれる内容の要旨
Tables Table 1-1. Console Parameters ..............................................................................1-13 Table 1-2. Modem Parameters ................................................................................1-16 Table 2-1. Console Parameters ..............................................................................2-20 Table 2-2. Modem Parameters ................................................................................2-24 Table 3-1. Summary of Initial Startup Opt
ページ16に含まれる内容の要旨
Table D-7. V.35 Interface (Order No. 7220) .............................................................. D-5 Table D-8. X.21 Interface (Order No. 7224) .............................................................. D-6 Table D-9. ISDN BRI Power Requirements .............................................................. D-7 Table D-10. ISDN BRI Clearances and Creepage Distances ..................................... D-9 Table D-11. ISDN BRI Safety Status (Order Nos. 24000, 24000-S, 50022, AE00
ページ17に含まれる内容の要旨
Preface Read this guide for instructions on how to install, start, and operate Access Node or 8-Port Access Node Hub models that have a single DC input switching power supply, the AN™/DC and ANH™-8/DC. This guide describes • Physically installing the AN/DC (Chapter 1) or the ANH-8/DC (Chapter 2) and attaching communications equipment • Connecting the AN/DC or ANH-8/DC to the network using one of the Site Manager software configuration options (Chapter 3) • Using the AN/DC or ANH-8/DC opera
ページ18に含まれる内容の要旨
Installing and Operating AN/DC and ANH-8/DC Systems Text Conventions This guide uses the following text conventions: angle brackets (< >) Indicate that you choose the text to enter based on the description inside the brackets. Do not type the brackets when entering the command. Example: If the command syntax is: ping , you enter: ping 192.32.10.12 bold text Indicates command names and options and text that you need to enter. Example: Enter show ip {alerts | routes}. Example: Use
ページ19に含まれる内容の要旨
Preface screen text Indicates system output, for example, prompts and system messages. Example: Set Trap Monitor Filters vertical line ( | ) Separates choices for command keywords and arguments. Enter only one of the choices. Do not type the vertical line when entering the command. Example: If the command syntax is: show ip {alerts | routes}, you enter either: show ip alerts or show ip routes, but not both. Acronyms This guide uses the following acronyms: AN/DC Access Node (AN) with DC powe
ページ20に含まれる内容の要旨
Installing and Operating AN/DC and ANH-8/DC Systems IEEE Institute of Electrical and Electronic Engineers IP Internet Protocol ISDN Integrated Services Digital Network ISO International Organization for Standardization ITU-T International Telecommunication Union –Telecommunication (formerly CCITT) LAN local area network LED light-emitting diode LMI Local Management Interface MAC media access control MAU media access unit MDI Medium-Dependent Interface MDI-X Medium-Dependent Interface with Crosso
